Epson Powerlite Pro G5200wnl Multimedia Projector Users Guide

							Preparing the Projector to Present Through a Network71
10. When you’re done making these settings, select Return, Setup 
complete
, and then Yes to confirm that you want to save the 
changes.
11. Press 
Menu to exit. 
Now you’re ready to set up your computer for wireless projecting. Go 
to “Configuring the Network Settings for Windows” below, or go to 
“Setting Up Your Mac for Access Point Mode” on page 77. If you 
want to enable security options for your network, see page 85 to set up 
the option that your network uses on the projector. 
Configuring the Network Settings for Windows
Before connecting to the projector, you need to make sure the settings 
for your computer’s wireless card or adapter match the settings you 
entered for the projector. 
1. Access your wireless network Properties window. For example, in 
Windows XP you would click 
Start > Control Panel > Network 
and Internet Connections
. Then click the Network 
Connections
 icon. You see a screen similar to this: 
2. Right-click the 
Wireless Network Connection icon and select 
Properties. 
note
On some Windows systems, 
you can right-click 
My Network Places or 
Network Neighborhood 
on the desktop and select 
Properties.
Settings may vary, 
depending on your wireless 
network adapter. See the 
documentation for your 
adapter for more 
information. 
Right-click and select Properties 
						

							72Preparing the Projector to Present Through a NetworkYou see a screen similar to this:
3. Click the 
Configure button.
4. Click the 
Advanced tab. You see a screen like this:
Click here 
						

							Preparing the Projector to Present Through a Network73
5. Check your wireless card’s or adapter’s device settings. 
(Depending on the type of card or adapter you’re using, some of 
the settings may be different than those listed here.)
■Set the Network Type to Infrastructure. 
■Set the SSID to match the name assigned to the access point 
(which should also match the projector’s SSID). 
■Make sure Encryption is Disabled if you have not set up 
encryption on the projector. 
6. Click the 
General tab and make sure that your wireless card or 
adapter is enabled. 
7. When you’re done, click 
OK to close the wireless properties dialog 
box. 
8. Right-click the 
Wireless Network Connection icon again and 
select 
Properties. You see this screen: 
						

							74Preparing the Projector to Present Through a Network9. Select 
Internet Protocol and click the Properties button. You 
see this screen:
10. If your access point uses DHCP, select 
Obtain an IP address 
automatically
. Otherwise select Use the following IP address 
and 
Use the following DNS server addresses, then enter the 
required information: 
■IP address: Type in the IP address you want to assign to the 
computer. It must be formatted like other addresses on the 
network. The last section/octet must be unique.
■Subnet mask: For example: 255.255.255.000, but this 
depends on how your network is set up.
■Default gateway: Enter the IP address that was assigned to 
the access point when it was set up.
■Preferred DNS server/Alternate DNS server: Enter the IP 
address of the DNS server(s) for your network.
11. When you’re done, click 
OK. 
note
For specific details about 
your network, please consult 
your network administrator.
note
If you don’t know your 
gateway or access point 
address, see page 76.  
						

							Preparing the Projector to Present Through a Network75
12. Click the Wireless Networks tab. (If you don’t see this tab, you 
may need to enable your wireless card or adapter by clicking 
Configure to access the device settings; then follow any 
instructions on the screen to enable the device.)
You see a screen like this:
13. Verify that you’ve enabled your computer’s connection to the 
access point. It should be listed with the small  icon next to it, 
indicating a connection. 
If it’s not listed, click 
Configure and type the name of your access 
point. 
14. When you’re done making settings, click 
OK to close the dialog 
box. 
Now you’re ready to connect to the projector. See “Projecting Over a 
Network” on page 90.  
						

							76Preparing the Projector to Present Through a Network
Checking the Gateway IP Address on Windows
If you’re entering IP addresses manually and need to find out the 
gateway IP address (the IP address of your access point), make sure the 
wireless connection to the access point is currently active, as described 
in the previous section. Then follow these steps:
1. Access your wireless network Properties window. For example, in 
Windows XP you would click 
Start > Control Panel > Network 
and Internet Connections
. Then click the Network 
Connections
 icon. You see a screen similar to this:
2. Right-click the 
Wireless Network Connection icon and select 
Status. 
note
If you cannot identify the 
gateway address using this 
Windows utility, use the 
administrator’s utility 
software that came with 
your access point. 
Right-click and select Status 
						

							Preparing the Projector to Present Through a Network77
3. Click the Support tab. The gateway’s IP address is listed as 
shown: 
Setting Up Your Mac for Access Point Mode
Your AirPort software is automatically configured to allow your Mac 
to detect Access Point networks. 
Typically, you only need to select your AirPort network name from 
the AirPort status menu on the Mac menu bar. If you’re having 
problems connecting to the projector, follow these steps:
1. From the Apple pull-down menu, select 
System Preferences. 
2. Click the 
Network icon. You see the Network settings window.
Gateway address 
						

							78Preparing the Projector to Present Through a Network3. Make sure Location is set to 
Automatic.
4. Select 
Network Port Configurations in the Show pull-down 
menu.
5. Under Port Configurations, select 
AirPort.
6. Click 
Apply Now. Then close the window.
7. Start the AirPort Admin utility. Select your base station, then 
click 
Configure.
8. On the AirPort tab, make sure your AirPort network name 
matches your projector’s SSID. If not, enter the projector’s SSID 
in the AirPort Network text box and click 
Update. 
9. If you turned DHCP on in your projector’s advanced menu, click 
the Network tab and make sure the 
Distribute IP addresses 
checkbox is selected. If you need to select it, click 
Update. 
Select 
Automatic 
Select Network Port 
Configurations 
Then select AirPort
note
If you don’t need the other 
network ports, disable them 
by deselecting their 
checkboxes. If more than one 
network port is enabled, the 
projector software warns you 
to turn off AirPort when you 
first connect the projector. 
Disregard this message.
Your AirPort network and 
base station names may be 
different. To check or 
change your AirPort 
network name, start the 
AirPort Admin utility, select 
your base station, and click 
Configure. Click Show 
All Settings, then make 
any changes you want on the 
AirPort tab.
If you’re connecting to your 
projector in static IP mode, 
deselect the 
Distribute IP 
addresses
 checkbox. Make 
sure your projector’s gateway 
address is identical to the 
base station’s IP address, 
and the first three segments 
of the projector’s IP address 
are identical to the first 
three segments of the base 
station’s IP address. 
						

							Preparing the Projector to Present Through a Network79
10. Click the AirPort icon on the menu bar at the top of the 
Macintosh desktop. You see the AirPort status menu:
11. Check to make sure AirPort is turned on.
12. Select the name of your AirPort network. 
Making a WPS (Wi-Fi Protected Setup) 
Connection
If you are using a WPS-compatible access point, you can configure the 
settings for the connection between the projector and the access point 
from the projector’s Configuration menu using one of these methods:
■Push Button Method
Press both the 
Enter button on the projector and the button on 
the access point to make the SSID and security settings. This 
method is recommended when the projector and access point are 
close together.
■PIN Code Method
With the PIN code method, you enter an 8-digit code from the 
computer to enable the SSID and security settings. The 
connection between the computer and the access point must have 
already been established. (For connection instructions, refer to the 
manual provided with the access point.) This method lets you 
make the settings without having to press any buttons on the 
projector, and is recommended when the projector is mounted on 
the ceiling. 
						

							80Preparing the Projector to Present Through a NetworkFollow these steps to open the WPS connection screen:
1. Press the 
Menu button to open the projector menu. 
2. Select 
Network, then Network Configuration, and press Enter.
The Network Configuration screen is displayed.
3. Select 
Wireless LAN and press Enter.