Epson Powerlite Pro G5200wnl Multimedia Projector Users Guide

							Maintaining the Projector131
3. Install two AA alkaline batteries, 
inserting the 
+ and – ends as 
shown.
4. Position the cover as shown, then 
press down until it snaps into 
place.
Transporting the Projector
The projector contains many glass and precision parts. Follow these 
guidelines to prevent damage: 
■When shipping the projector for repairs, use the original 
packaging material if possible, including the protective lens pads. 
If you do not have the original packaging, use equivalent 
materials, placing plenty of cushioning around the projector.
■When transporting the projector a long distance, first place it in a 
hard-shell shipping case, then pack it in a firm box with 
cushioning around the case. 
■Attach the lens cover to the lens.
■If an SD card is installed, remove it from the projector.
■Return the projector feet to their stored (highest) positions.
■Turn the vertical lens shift dial so that the lens is in its lowest 
position.
note
Epson shall not be liable for 
any damages incurred 
during transportation. 
						

							132Maintaining the Projector 
						

							8
133
8
Solving Problems
This chapter helps you solve problems with your projector, and tells 
you how to contact technical support for problems you can’t solve 
yourself. The following information is included:
■Using the projector’s on-screen help system
■What to do when the projector’s status lights flash
■Solving projector operation problems
■Solving problems with the image or sound
■Solving network problems
■Solving problems with the remote control
■Contacting technical support 
						

							134Solving Problems
Using On-Screen Help
If the image doesn’t look right or your audio isn’t working, you can 
get help by pressing the 
? Help button on the back of the projector or 
on the remote control.
1. Press the 
? Help button on the remote control or on the 
projector. 
You see the Help menu:
2. Use the  pointer button on the remote control or the 
navigational buttons on the projector to highlight menu items.
3. Press the 
Enter button on the remote control or on the projector 
to select the menu item. 
4. To exit the help system, press the 
? Help button.
If none of the suggestions solve your problem, see additional solutions 
to problems in the following sections. 
						

							Solving Problems135
Checking Projector Status
If your projector isn’t working correctly, first turn it off and unplug it. 
Then plug the power cord back in and turn on the projector. If this 
doesn’t solve the problem, check the lights on top of the projector.
What To Do When the Lights Flash
The lights on top of the projector indicate the projector’s status.
Refer to the following table for a complete description of the 
projector’s status lights:
Temperature light
Lamp light
Power light
Wireless LAN status light 
(G5150NL and G5350NL only)
Status lights
Light Status Description
Orange The projector is in sleep or standby mode. You can unplug it or press the 
P power button to turn it on.
Flashing green The projector is warming up. Wait for the image to appear.
Green The projector is operating normally.
Red or 
flashing redThere is a problem with the projector. Check the other two lights and the 
information on page 136 to diagnose the problem.  
						

							136Solving Problems
Flashing orange It’s time to replace the lamp. See page 126 for instructions. If you 
continue to use the lamp after the replacement warning, there is an 
increased possibility that the lamp may break.
Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, 
projection will stop automatically if the temperature rises higher. Make 
sure there is plenty of space around and under the projector for 
ventilation, and that the air filter and vents are clear.
Red The projector is overheating, which turns the lamp off automatically. 
Wait until the projector switches to standby mode (about 5 minutes). 
Make sure the room temperature is not above 95 °F (35 °C), and there is 
plenty of space around and under the projector for ventilation. 
The air filter may be clogged. Clean or replace the air filter as described 
on pages 122 to 126.
If you’re using the projector above an altitude of 4,900 feet (1,500 
meters), turn on High Altitude Mode in the Operation menu (see 
page 107).
If the projector continues to overheat after you clean the air filter, the 
problem may be caused by damage to the cooling fan or temperature 
sensor. Contact Epson for help as described on page 146.
Warning: Except as specifically explained in this User’s Guide, do not 
attempt to service this product yourself.
Flashing red Power is cut off because of an internal problem. Unplug the power cord 
and contact Epson for help, as described on page 146.
Flashing red  There is a problem with the fan or temperature sensor. Stop using the 
projector, disconnect the power cord, and contact Epson as described on 
page 146.
Flashing red The lamp may be burnt out. First make sure the lamp cover is securely 
installed. If that’s not the problem, the air filter may be clogged. Clean or 
replace the air filter as described on pages 122 to 126.
If this does not resolve the problem, let the lamp cool and then remove it. 
If the lamp is cracked, replace it as described on page 126. If the lamp is 
not cracked, reinstall it. If reinstalling doesn’t work, replace the lamp.
If you’re using the projector above an altitude of 4,900 feet (1,500 
meters), turn on High Altitude Mode in the Operation menu (see 
page 107).
If none of these suggestions resolves the problem, contact Epson as 
described on page 146.
Status lights (continued)
Light Status Description 
						

							Solving Problems137
Solving Projector Operation Problems
The power doesn’t turn on.
■If the projector doesn’t turn on when you press the Ppower 
button, make sure the power cord is connected to the projector 
and plugged into a working electrical outlet.
■The power cord may be defective. Disconnect the cord from the 
outlet and contact Epson as described on page 146.
■If you’re using the Direct Power On function and you 
immediately plug the power cord back in after unplugging it, the 
power may not turn back on. Press the Ppower button to turn 
the projector back on.
The buttons on the projector don’t work.
If the Control Panel Lock function has been enabled, you can’t use the 
buttons on the projector. Try using the remote control instead (make 
sure it is set to the correct ID). See page 106 for information about the 
Control Panel Lock function.
Solving Problems With the Image 
or Sound
No image appears on the screen.
■Check that the Ppower light is green, not flashing. 
■The projector may be in standby or sleep mode. If the Ppower 
light is orange, press the Ppower button to turn the projector on.
■If the power was switched off and then on again, the projector 
may be cooling down. Wait until the Ppower light stops flashing 
and remains orange; then press the Ppower button again.
■Press the A/V Mute button on the remote control to make sure 
the picture has not been turned off temporarily.  
						

							138Solving Problems
■The attached computer may be in sleep mode or displaying a 
black screen saver. Try pressing a key on the computer.
■If you are projecting from a DVD player or other video source, 
make sure you turn it on and press its 
Play button.
■If you are projecting from a video source, make sure the Video 
Signal setting is correct (see page 98).
■You can also try resetting all of the configuration menu settings. 
See page 95.
You’ve connected a computer and see a blue screen with the 
message 
No Signal displayed.
■Make sure the cables are connected correctly, as described on 
page 19.
■If you’ve connected a computer and one or more video sources, 
you may need to press the 
Source Search button on the 
projector or one of the source buttons on the remote control to 
select the correct source. Allow a few seconds for the projector to 
sync up after pressing the button.
■Make sure the power for your connected equipment is turned on.
If you’re using a PC notebook: 
■Hold down the Fn key on the keyboard and press the function 
key that lets you display on an external monitor. It may have an 
icon such as  , or it may be labelled 
CRT/LCD. Allow a few 
seconds for the projector to sync up after pressing it. Check your 
notebook’s manual or online help for details. 
On most systems, the   key lets you toggle between the LCD 
screen and the projector, or display on both at the same time.
If you connect the notebook while the projector or computer are 
already turned on, the function 
Fn key that changes the 
computer’s image signal to external output may not work. Turn 
the computer and the projector off and then back on again. 
						

							Solving Problems139
■Depending on your computer’s video card, you might need to use 
the Display utility in the Control Panel to make sure that both the 
LCD screen and external monitor port are enabled. See your 
computer’s documentation or online help for details.
If you’re using Mac OS X:
1. Open 
System Preferences. 
2. Click 
Displays.
3. Click 
Detect Displays. 
4. Make sure the 
VGA Display or Color LCD dialog box is selected.
5. Click the 
Arrangement or Arrange tab.
6. Make sure the 
Mirror Displays checkbox is selected. 
The message Not Supported is displayed.
■Make sure the correct input signal is selected in the Signal menu 
(see page 98).
■Make sure your computer’s resolution and frequency or refresh 
rate is supported by the projector (see page 159). If necessary, 
change your computer’s settings. 
Only part of the computer image is displayed.
■Press the Auto button on the remote control or the Enter button 
on the projector.
■Make sure the image Position setting is correct in the Signal 
menu. See page 99 for more information.
■Press the Aspect button on the remote control.
■Press the Esc button on the remote control to cancel the E-Zoom 
function.
■Make sure your computer’s resolution setting is correct. See the 
compatible video formats listed on page 159. 
						

							140Solving Problems
■You also may need to modify existing presentation files if you 
created them for a different resolution. See your software 
documentation for specific information.
■If you’re projecting a wide panel computer image, adjust the 
Resolution setting (see page 98).
■If you’re projecting an image from a computer with dual display 
activated, turn dual display off.
The image isn’t square, but keystone-shaped.
If the image isn’t square or rectangular, adjust its shape as described on 
page 47.
The image contains static or noise.
■If you’re using a computer cable longer than 6 feet (1.8 meters), 
or an extension cable, the image quality may be reduced.
■Keep your computer and video cables away from the power cord 
as much as possible to prevent interference.
■The video signal may be split between the computer and the 
projector. If you notice a decline in the projected image quality 
when the image is displayed simultaneously on your notebook 
computer and the projector, turn off the notebook’s LCD display.
■Make sure the correct input signal is selected in the Signal menu 
(see page 99).
■If you’ve used the Quick Corner or Keystone adjustment, you 
may need to decrease the 
Sharpness setting in the Image menu 
(see page 97).
■If you’re projecting from a computer, make sure its signal is 
compatible with the projector. See page 159.
The image is blurry.
■There may be dirt or smears on the lens. Clean the lens as 
described on page 122.
■Adjust the focus using the focus ring (see page 46).