Epson Powerlite Pro Cinema 9500 Ub Users Guide

							Making Detailed Adjustments41
■RGBCMY
Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 29).
Use the RGBCMY settings to adjust the hue, saturation, and brightness of the six color 
components (red, green, blue, cyan, magenta, yellow). After adjusting each color, press 
Esc to move to another menu option. You can also access this setting by pressing the 
RGBCMY button on the remote control. See page 31 for more information. 
■Gamma
Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 29).
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from 
your image or a displayed graph. Lower values will increase the contrast of dark areas, but 
tend to blur the bright areas. Higher values will darken the light areas.
You can also access this setting by pressing the 
Gamma button on the remote control. 
See page 30 for more information.
■Contrast Enhancement (Pro Cinema 9500 UB only)
Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 29).
This setting automatically enhances contrast by calculating based on the current contrast. 
You can select from 3 levels of contrast enhancement.
■Super-resolution (Pro Cinema 9500 UB only)
This setting sharpens blurred images, enhancing the apparent detail of the image. You can 
select from 3 levels of enhancement. Note that intentionally blurred parts of the image, 
such as out-of-focus backgrounds, may become sharper.
Image > Advanced > RGBCMY
Image > Advanced > Gamma
Image > Advanced > Contrast Enhancement
Image > Advanced > Super-resolution 
						

							42Making Detailed Adjustments
Adjustments for Computer Images
In addition to the settings described previously, you can adjust the Tracking and Sync settings 
for analog RGB computer images. Normally, these settings are adjusted automatically by the 
projector. If you notice that the image is blurry or contains dark vertical bands, you may need 
to adjust the settings yourself.
■Auto Setup
Leave this setting on so that the projector automatically adjusts the tracking, sync, and 
position of the image.
■Tracking
Adjust the tracking to eliminate vertical bands. It is easiest to 
adjust the tracking when the image contains a lot of fine detail 
(such as black text on a white background).
■Sync.
Adjust the synchronization to eliminate blurriness. For best results, 
make sure the tracking is properly adjusted first.
Selecting Memory Settings and Resetting the 
Projector
Your projector comes with 8 memory locations that are reserved for color mode calibration by 
installers. In addition, there are 2 memory locations where you can save other customized 
settings to obtain the best picture quality for each of your video inputs.
Signal > Auto Setup
Signal > Tracking
Signal > Sync. 
						

							Making Detailed Adjustments43
Selecting Memory Settings
You can easily recall the memory settings by using the 
memory button on the remote control.
1. Press the 
Memory button on the remote control. 
2. Select 
Load Memory.
3. Use the arrow buttons to select the desired setting, then 
press the 
Enter button. 
After a moment, the image appears on the screen using 
the retrieved settings. Certain settings may not be 
applied, depending on the input signal.
Creating Memory Settings
Memory settings can be used to store most of the picture quality settings on page 37 and color 
settings on page 39. Before saving them to memory, adjust the settings to the desired levels.
1. Press the 
Memory button on the remote control.
2. Select 
Save Memory.
3. Select the memory name you want to use, then press the 
Enter button to save your 
settings.
Note: Saved settings are indicated by a green highlight  next to the memory name. If you select 
a name that is already in use, the existing settings will be erased and new ones saved in their 
place. 
Renaming Memory Settings
With the Pro Cinema 9500 UB, you can rename memory settings so that they are easier for 
you to recognize.
1. Press the 
Memory button on the remote control.
2. Select 
Rename Memory.
3. Select the memory name you want to change, then press the 
Enter button. The name 
selection screen is displayed.
4. Do one of the following:
■To select a name from the displayed preset names, select the desired name and press 
the 
Enter button.
Memory 
button 
						

							44Making Detailed Adjustments
■To create your own name, select Customized and use the keyboard screen to enter 
the name. Use the arrow buttons to select a character, then press the 
Enter button. 
When you have selected all of the characters in your name, select 
Finish and press the 
Enter button.
Deleting Saved Memory Settings
You can clear all your memory settings at once.
1. Press the 
Menu button on the remote control.
2. Open the 
Reset menu, then select Reset Memory.
3. Select 
Yes, then press the Enter button to delete the memory settings.
Note: You can delete memory settings one at a time with the Erase Memory setting under the 
Memory menu.
Resetting the Projector
If the image quality isn’t what you expect, one or more settings may be adjusted improperly. 
If necessary, you can restore the projector to its factory-default (original) settings. 
To restore the settings in a specific menu (such as the Image or Settings menu), open that 
menu, select 
Reset, and confirm as needed. The example below shows how to reset the 
Image menu settings:
You can also reset the lamp usage timer or restore all the projector settings to their original 
values. Follow these steps:
1. Press the 
Menu button on the remote control.
2. Open the 
Reset menu.
Open the Image 
menu . . .
and select Reset 
						

							Making Detailed Adjustments45
3. Do one of the following:
■Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero. 
You should reset the lamp timer only when you install a new projector lamp. See 
page 55 for more information.
■Select Reset Memory to clear all memory settings.
■Select Reset All to return all projector settings to their original defaults (except 
Component, Save Memory, Language, and Lamp).
Customizing Projector Features
Use the settings in this section to adjust the image size and position, suppress on-screen text, 
and select basic setup options.
Image Sizing
Before adjusting any of these settings, make sure you have already selected an appropriate 
aspect ratio for the type of picture you’re viewing (see page 28). 
■Overscan
For component video formats, this setting lets you see the edges of the image that are not 
normally visible in the picture (see page 68). If you see interference when you set 
Overscan to 100%, try adjusting the Position as described below. 
■Position
Note: This setting cannot be used with a signal input through the HDMI 1 or HMDI 2 port.
Use the arrow buttons to fine-tune the position of the image on the screen.
■Aspect
This setting lets you change the aspect ratio of your image, and works the same as 
pressing the 
Aspect button on the remote control. See page 28 for more information.
Signal > Advanced > Overscan
Signal > Position
Signal > Aspect 
						

							46Making Detailed Adjustments
■Zoom Caption Pos.
Lets you adjust the shape and position of the image so that subtitles are visible (available 
only if the aspect ratio has been set to 
Zoom). Use Zoom Size to adjust the proportions 
of the image, and 
Zoom Caption Pos. to move the image up or down. Adjust overscan 
before changing the zoom position.
Screen Options
■Messages
Turn this setting off if you want to prevent on-screen messages from appearing (such as 
the no-signal message, or the identifying text that appears when you switch between 
image sources or color modes). 
■Startup Screen
Turn this setting off if you want to prevent the startup screen from appearing while the 
projector is warming up.
■Display Background
Changes the screen that’s used when the projector is not receiving a signal or when you 
press the 
Blank button to temporarily stop projection.
Other Setup Options
■Projection
You can select different options for projecting the image: Front, Front/Ceiling, Rear, 
Rear/Ceiling.
■Direct Power On
Sets projection to start when the main power switch is turned on, without pressing the 
Ppower button on the remote control or the projector. 
Note: When direct power on is enabled, power surges that occur after a power outage can 
cause the projector to turn on.
Signal > Zoom Caption Pos.
Settings > Display > Messages
Settings > Display > Startup Screen
Settings > Display > Display Background
Settings > Projection
Settings > Direct Power On 
						

							Making Detailed Adjustments47
■Video Signal
Leave this setting on Auto so the projector can automatically interpret the format, such as 
NTSC or PAL (for standard TV formats). 
■Component
Change this setting to match the type of equipment connected to the Component port. 
For component video, select 
Auto to let the projector automatically interpret the signal; 
or select 
YCbCr or YPbPr to manually select your video equipment’s signal.
■Trigger Out
Turn on this setting to have the Trigger out port output a 12-volt signal to lower your 
projection screen when the projector is running. For the Pro Cinema 9500 UB, select 
Power to signal when your projector is turned on, or Anamorphic Wide to engage a 
motorized anamorphic lens (commercially available) when that aspect ratio is selected.
Note: If you change this setting, the new setting will take effect the next time you turn the 
projector on.
■Illumination
Turn off this setting to deactivate the lights on the projector’s Ppower and  source 
buttons. Use this setting if you find the lights distracting in a darkened room.
■Sleep Mode
Turn off this setting if you don’t want the projector to enter sleep mode. (Sleep mode 
shuts the projector off automatically when there is no video signal.) 
Select 
5min., 10min., or 30min. as the length of time before shutoff; decreasing the time 
conserves power and extends the life of the lamp. 
To turn the projector back on, press the Ppower button on the remote control or the 
projector.
■Child Lock
Lets you lock the Ppower button on the projector’s control panel to make it more 
difficult for a child to turn on the projector. See page 32 for more information.
Settings > Input Signal > Video Signal
Settings > Input Signal > Component
Settings > Trigger Out
Settings > Illumination
Settings > Sleep Mode
Settings > Child Lock 
						

							48Making Detailed Adjustments
■Control Panel Lock
Lets you disable all the buttons on the projector’s control panel to prevent the image from 
being accidentally changed once it is adjusted. See page 32 for more information.
■High Altitude Mode
Adjusts the speed of the fan so it can properly cool the projector at higher altitudes. Turn 
this setting on if you are using the projector at an altitude of 4900 feet (1500 meters) or 
higher.
Settings > Control Panel Lock
Settings > High Altitude Mode 
						

							Maintenance49
Maintenance
Your projector needs little maintenance. All you need to do on a regular basis is keep the lens 
clean. You also may need to clean the air filter to prevent overheating.
Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never 
open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages 
in the projector can injure you severely. Do not try to service this product yourself, except as 
specifically explained in this User’s Guide. 
The only parts you should replace are the air filter and the lamp. If another part needs 
replacing, contact your dealer or a qualified servicer.
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on 
the surface. 
■Use a blower brush that is designed for camera 
equipment to remove dust from the lens.
■To remove dirt or smears, use a lens cloth or 
tissue. If necessary, moisten the cloth with lens 
cleaner and gently wipe the lens surface.
Caution: Never rub the lens with abrasive materials. Use 
only lens cleaning fluids that are designed for cleaning 
optics. 
						

							50Maintenance
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case 
with a soft, dry, lint-free cloth.
■To remove stubborn dirt or stains, 
moisten a soft cloth with water and a 
neutral detergent. Then wipe the case 
and dry it with a dry cloth.
Caution: Never use wax, alcohol, benzene, 
thinner, or other chemical detergents. These 
can damage the case.
Cleaning and Replacing the Air Filter
Your projector includes an air filter to ensure the best performance. If dust collects on the air 
filter, clean it as described below. Dust clogs prevent proper ventilation and cause overheating 
and damage to the projector.
1. Press the Ppower button and wait for the Ppower light to stop flashing. The projector 
cools down.
2. Turn off the projector using the power switch on the back.
3. Unplug the power cord and disconnect any cables.
4. Turn the projector over (unless it’s ceiling mounted).
5. Push down on the tabs on the filter cover to remove it.
6. Remove the air filter as shown.