Epson Powerlite Pro Cinema 1080 Ub Users Guide

							Making Basic Adjustments31
Adjusting the Gamma Setting
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your 
image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to 
blur the bright areas. Higher values will darken the light areas. Gamma presets make minor 
adjustments to mid-tone values. The larger the gamma preset, the lower the midtone values. 
Changing these settings affects contrast which can be seen as a blur in bright areas.
1. Press the 
Gamma button. You see the following displayed on the screen:
2. Do one of the following:
■Select one of the numeric correction values using the u or d button on the remote 
or control panel and press the
 Select button. You see the setting reflected in the 
graph on the right. The horizontal axis represents the input signal level, and the 
vertical axis represents the output signal level. Press the 
Gamma button to exit.
■Select Customized. Then continue with the next step.
3. Do one of the following:
■Select Adjust it from the image. You see a gamma icon on the projected image. Use 
the arrow buttons to move the icon to the area of brightness you want to adjust, then 
press 
 Select. The custom gamma graph appears with the channel selected for 
adjustment. Press the u or d button to adjust and then press 
 Select.
■
Select Adjust it from the graph. When the gamma graph appears, use the l or r 
button to select the point on the graph that you want to adjust, and then use the 
uord button to adjust the settings. Press 
 Select to save your setting and exit.  
						

							32Making Basic Adjustments
Locking the Projector
The projector includes two lock settings to prevent the image from being accidentally 
changed once it’s adjusted, and to keep children from turning on the projector without adult 
supervision. 
To access the lock settings, follow these steps:
1. Press the 
Menu button on the remote control.
2. Use the menu navigation buttons to open the 
Settings 
menu.
3. Choose from these options:
■Child Lock to disable the PPower button on the 
projector’s control panel unless it is pressed for 
about 3 seconds. (You can use the P
Power 
button to turn it off, however.) Since you can still 
use the remote control to turn on the projector, 
you may want to keep it away from children’s reach.
■Control Panel Lock to disable all the buttons on the projector’s control panel. A 
lock icon appears on the screen whenever you press a button with Control Panel 
Lock turned on. To operate the projector, you must use the remote control. To 
cancel Control Panel Lock, press and hold the
 Select button on the projector’s 
control panel for at least 7 seconds.
4. Press 
Menu to exit the menu system. 
If you turned on the Control Panel Lock, the projector buttons are now locked.
If you turned on the Child Lock, turn off the projector and let it cool down. The Child 
Lock takes effect after the cool-down period.
Menu 
button
Menu 
navigation 
buttons 
						

							Making Detailed Adjustments33
Making Detailed Adjustments
You can use the projector’s on-screen menus to make detailed adjustments to the image 
quality—such as the brightness, contrast, sharpness, and color. You can also change the menu 
display, sleep mode settings, and other projector features. 
Using the Menu System
You can access the menu system either from the remote control or the buttons on the 
projector’s control panel. You can access the full menu or a line menu that lets you adjust the 
Picture and Memory settings while viewing their effects on your display. You can also change 
the menu language and control how the menus display (see page 34). 
1. To display the full menu, press the 
Menu button on the projector or remote control. You 
see a display like this one (the actual display depends on the connected equipment):
Note: Depending on which equipment is connected to the projector, some options may not be 
available.
2. Press the u or d button to highlight a main menu option (Image, Signal, Settings, 
Memory, Info or Reset), then press the Select button to select it.
3. Press the u or d button to highlight a setting, then press the 
Select button.
4. Press the u, d, l, or r button to change settings as necessary. You may have to press the 
Select button to confirm your choice. 
Main menu 
optionsSettings available 
for the highlighted 
menu 
						

							34Making Detailed Adjustments
5. When you’re finished, press the Esc button to return to the previous menu or press the 
Menu button to exit the menu system.
To display one of the line menus of the Image menu, press the 
Select button. You see a 
display like this at the bottom of the image:
Press the u or d button to highlight an option (if necessary), then press the l or r button to 
adjust it. Press the 
Esc button to return to the previous menu or the Menu button to exit the 
menu system. Press the 
Memory button to return to the setting stored in memory.
You can access the following settings through the line menu while viewing their effects on 
your display:
■Brightness (see page 36)
■Contrast (see page 36)
■Sharpness (see page 37)
■Color Saturation (see page 38)
■Tint (see page 39)
■Absolute Color Temperature (see page 30)
■Skin Tone (see page 30)
■Brightness Control (see page 37)
■Auto Iris (see page 36)
Changing How the Menus Display
Use these options to control how the menus display.
■Language
Select from 20 languages to use in the menu system. 
■Menu Position
Use the arrow buttons to choose a position on the screen for displaying the menu.
SettingsÆLanguage
SettingsÆDisplayÆMenu Position 
						

							Making Detailed Adjustments35
■Menu Color
Select a color scheme for displaying the menus.
Adjusting the Picture Quality
Before fine-tuning the image using these adjustments, make sure you have already selected the 
best Color Mode for your picture and viewing environment, as described on page 29. Then 
use the settings in this section to finish adjusting the picture to your liking. 
Most image quality settings are saved independently for each input source (Video, S-Video, 
HDMI1, HDMI2, Component, PC) and color mode. After you finish adjusting the settings 
for one input source, switch to the other input sources you’ll be using and make any necessary 
adjustments.
Input Brightness Settings
If the signal from connected equipment is weak and images appear dark, you can adjust the 
Brightness and Contrast settings. You can adjust brightness and contrast for each image 
source and color mode.
Adjust this setting first, then fine-tune the image with the remaining settings.
The Brightness setting controls how much light is produced by the projector, and the 
Contrast setting adjusts the difference between the bright and dark areas of the projected 
image. The other settings listed on the following page control how the projector interprets the 
light and dark areas of the picture. 
SettingsÆDisplayÆMenu Color 
						

							36Making Detailed Adjustments
■Brightness
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Adjust the brightness so it’s suitable for your viewing conditions. For example, if you’re 
projecting in a brightly lit room or onto an especially large screen, you may need to 
increase the brightness. Decrease the brightness for dark rooms or small screens; this also 
reduces power consumption and fan noise, and helps to prolong the life of the lamp. 
■Contrast
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
This setting adjusts the difference between bright and dark areas.
■Auto Iris
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
When this setting is on, the amount of light produced by the lamp is automatically 
adjusted according to the brightness of the image. The setting is stored separately for each 
image source and color mode.
■Setup Level
This setting adjusts the threshold at which dark areas of the image are rendered black 
(0 IRE). For compatibility with most DVD and video equipment sold in the United 
States, leave this setting at 0%. Check your video equipment’s specifications to be sure of 
the correct setting. 
■EPSON Super White
Note: This setting can be used only when the Color Mode is set to Natural, Cinema Night, HD, 
or Silver Screen (see page 29).
If bright parts of the image are washed out or overexposed (when the input signal 
contains values over 100 IRE), turn this setting on to compensate. When this setting is 
turned on, the projector disregards the HDMI Video Range setting. 
ImageÆBrightness
ImageÆContrast
ImageÆAuto Iris
SignalÆSetup Level
SignalÆEPSON Super White 
						

							Making Detailed Adjustments37
■HDMI Video Range
Note: This setting can be used only when either HDMI1 or HDMI 2 is selected as the image 
source (see page 23).
If your video equipment has an HDMI port and you’ve connected it to the projector 
using an HDMI cable, set the level of the projector to match that of the video equipment. 
When this setting is turned on, the projector disregards the EPSON Super White setting.
■Brightness Control
This setting controls the light output from the projector. On high, the lamp uses 170 W 
of power. On low, the lamp uses 135 W.
Sharpness and Picture Quality Settings
If the image looks fuzzy, or if it contains noise or flickering, you can use these settings to 
correct it.
■Sharpness
Use this function to make lines and edges appear more distinct in the image. This setting 
is stored separately for each image source and color mode setting. You can select 
Standard to adjust the sharpness of the entire image, or select Advanced to access the 
following submenu:
Choose 
Thin-Line Enhancement to sharpen details such as hair and clothing. Choose 
Thick-Line Enhancement to sharpen large contours and backgrounds. 
■Progressive
The projector uses 3D DigiScan HD Circuitry Processing for video-sourced images. For 
film-sourced images, the projector uses 3-2 pulldown detection and optimizes the image 
accordingly. 
SignalÆHDMI Video Range
ImageÆBrightness Control
ImageÆSharpness
SignalÆProgressive 
						

							38Making Detailed Adjustments
Leave this setting on Video for most purposes. Set to Film/Auto when the input source is 
a film, and you want to project an image closer to its original source. 
Note: This setting applies only when viewing composite video, S-video, component video, or 
480i, or 1080i RGB video (see page 63).
■Motion Detection
This setting specifies how signals are converted to progressive signals. Select a lower 
setting for slow-moving or still images (
S) or select a higher number for video images 
(
M).
Note: This setting applies only when viewing composite video, S-video, component video, or 
480i, or 1080i RGB video.
■Noise Reduction
This setting reduces flickering of analog images. You can select from 3 levels of noise 
reduction.
■2-2 Pull-down 
This setting will not be selectable if your DVD player does not support this mode. This 
mode applies only when a 24 fps (frame per second) 1080p signal is being input into 
Component, HDMI1, or HDMI2.
Color Settings
If the image colors don’t look correct, you can adjust them using these settings. Use the first 
three settings described below to make the most visible changes. If you only need to make 
slight adjustments, you can fine-tune the picture with the remaining settings. Most color 
settings are stored separately for each image source and color mode.
■Color Saturation
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Adjusts the color intensity of the image. 
SignalÆMotion Detection
SignalÆNoise Reduction
SignalÆ2-2 Pull-down
ImageÆColor Saturation 
						

							Making Detailed Adjustments39
■Tint
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Shifts the color balance between magenta and green. 
■Abs. Color Temp.
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Shifts the color balance between red and blue, making the image appear warmer or 
cooler. You can also access this setting by pressing the 
ColorTemp. button on the remote 
control. See page 30 for more information.
■Skin Tone
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Makes fine adjustments to the tint and controls the amount of magenta or green in the 
image. Also useful for correcting black-and-white images, if they look tinted. You can 
access this setting by pressing the 
S. Tone button on the remote control. See page 30 for 
more information.
■RGB
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Use the RGB settings to fine-tune the color of the image. You can adjust the offset and 
gain for each signal color (red, green, and blue). Use 
Offset to adjust darker shades and 
Gain for the lightest shades. 
ImageÆTint
ImageÆAbs. Color Temp.
ImageÆSkin Tone
ImageÆAdvancedÆRGB 
						

							40Making Detailed Adjustments
■RGBCMY
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
Use the RGBCMY settings to adjust the hue and saturation of the six color components 
(red, green, blue, cyan, magenta, yellow). After adjusting each color, press 
Esc to move to 
another menu option. 
■Gamma
Note: This setting cannot be adjusted when Color Mode is set to x.v. Color. 
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from 
your image or a displayed graph. Lower values will increase the contrast of dark areas, but 
tend to blur the bright areas. Higher values will darken the light areas.
You can also access this setting by pressing the 
Gamma button on the remote control. 
See page 31 for more information.
Adjustments for Computer Images
In addition to the settings described above, you can adjust the Tracking and Sync settings for 
analog RGB computer images. Normally, these settings are adjusted automatically by the 
projector. If you notice that the image is blurry or contains dark vertical bands, you may need 
to adjust the settings yourself.
■Auto Setup
Note: This setting only appears when a computer signal is being input to the PC port.
Leave this setting on so that the projector automatically adjusts the tracking, sync, and 
position of the image.
ImageÆAdvancedÆRGBCMY
ImageÆAdvancedÆGamma
SignalÆAuto Setup