Epson Powerlite Presenter Users Guide

Doing More with PowerLite Presenter51
■Child Lock: Turn this setting on to lock the   button on the control panel. See 
page 46 for more information.
■ High Altitude Mode: Turn this setting on if you use the projector at an altitude 
above 4900 feet (1500 meters), to ensure that the projector does not overheat.
4. Press   or   to adjust the setting.
5. Press   to exit the menu.
Signal Menu
1. Press   on the remote control. You see the Visual Setup menu.
2. Press   to highlight 
Signal, then press   to...

52Doing More with PowerLite Presenter
Viewing Status Information and Resetting the Lamp Timer
You can use the Info page on the Visual Setup menu to view the number of hours the lamp 
has been used, and to reset the timer after you install a new lamp. You can also view video 
signal information and error codes for any problems that occur.
1. Press   on the remote control. You see the Visual Setup menu.
2. Press   to highlight 
Info, then press   to display the lamp usage and other 
information.
Note:  If...

Caring for Your PowerLite Presenter53
Caring for Your PowerLite 
Presenter
The projector needs little maintenance. All you need to do on a regular basis is keep the lens 
clean. You also may need to clean the air filter to help prevent overheating.
Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never 
open any part of the projector, except as described in this  User’s Guide. Dangerous electrical 
voltages in the projector can injure you severely. Do not try...

54Caring for Your PowerLite Presenter
Cleaning the Case
Before you clean the case, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral 
detergent. Wring the cloth as dry as possible, then wipe the case.
Caution: Never use wax, alcohol, benzene, thinner, or other chemical detergents. These can 
damage the case. Never spray cleaners directly on 
the...

Caring for Your PowerLite Presenter55
3. If you need to clean or replace the filter, lift up the handle, press up on the tab, and lift off the cover.
4. Remove the old filter and install the new filter.
5. Replace the cover. 

56Caring for Your PowerLite Presenter
Replacing the Lamp
The life span of the lamp is about 4000 hours if Power Consumption in the Signal menu is set 
to Normal, and about 5000 hours if Power Consumption is set to ECO.
You can check how long the lamp has been used as described on page 52. If the number 
shown is close to the limit, make sure you have a spare lamp handy.
Note:  Turn off this product when not in use to prolong the life of the projector.
It’s time to replace the lamp when:
■The projected...

Caring for Your PowerLite Presenter57
3. Loosen the lamp cover screw using the screwdriver that came with the replacement lamp. (The screw won’t come all the way out.) Then slide out the lamp cover and lift up to 
remove it.
4. Loosen the two silver screws holding the lamp in place. (You can’t remove these screws.)
5. Grasp the lamp handle as shown and pull the lamp straight out.
Note:   The lamp(s) in this product contain mercury. Please consult your state and 
local regulations regarding disposal or...

58Caring for Your PowerLite Presenter
6. Gently insert the new lamp and tighten its screws.
Caution: Don’t touch the glass portion of the lamp with your bare hands; the invisible residue 
left by the oil on your hands may shorten the lamp life. Use a cloth or gloves to handle the new 
lamp assembly.
7. To replace the lamp cover, slide it into position, then tighten the screw. (The projector  won’t work if the lamp cover is loose.)
8. After replacing the lamp, you need to reset  the lamp timer, as...

Caring for Your PowerLite Presenter59
4. Press   again. You see the following on the screen:
5. Select 
Yes and press   or   to reset the timer.
The lamp usage timer displays 
0 H (zero hours) until you’ve  used the lamp for at least 
10 hours.
Storing PowerLite Presenter
Follow these guidelines when storing the projector:
■Make sure the temperature and humidity of the storage area are within the recommended 
range for the projector: 14 to 140 °F (–10 to 60 °C) and 20 to 80% relative humidity 
without...

60Caring for Your PowerLite Presenter
Transporting PowerLite Presenter
Note: Epson shall not be liable for any damages incurred during transportation.
Your projector contains many glass and precision parts. If you need to transport it, follow 
these guidelines to prevent damage:
■When shipping the projector for repairs, use the original packaging material if possible. If 
you do not have the original packaging, use equivalent materials, placing plenty of 
cushioning around the projector. Be sure th e...