Epson Powerlite Home Cinema 3010e Users Guide

Making Detailed Adjustments51
Deleting Saved Memory Settings
You can clear all your memory settings at once.
1. Press the 
Menu button on the remote control.
2. Open the 
Reset menu, then select Reset Memory.
3. Select 
Yes, then press the Enter button to delete the memory settings.
Note: You can delete memory settings one at a time with the Erase Memory setting under the 
Memory menu.
Resetting the Projector
If the image quality isn’t what you expect, one or more settings may be adjusted improperly. 
If...

52Making Detailed Adjustments
3. Do one of the following:
■Select Reset Lamp Hours to clear the lamp usage timer and reset it to zero. 
You should reset the lamp timer only when you install a new projector lamp. See 
page 67 for more information.
■Select Reset Memory to clear all memory settings.
■Select Reset All to return all projector settings to their original defaults (except Input 
Signal, User Button, Language, and Lamp Hours).
Customizing Projector Features
Use the settings in this section to...

Making Detailed Adjustments53
■Aspect
This setting lets you change the aspect ratio of your image, and works the same as 
pressing the 
Aspect button on the remote control. See page 27 for more information.
Note: When displaying 720p, 1080i, or 1080p signals through the HDMI or Component video 
port, the aspect ratio is automatically selected and you cannot change it.
If you display a 4:3 image using the Zoom setting, the top and bottom will be cut off. You can 
use the Zoom Caption Pos. option and other...

54Making Detailed Adjustments
Other Setup Options
■Projection
You can select different options for projecting the image: Front, Front/Ceiling, Rear, 
Rear/Ceiling.
Note: Only the Front option is available when the Color Mode is set to Auto.
■Direct Power On
Sets projection to start without pressing the Ppower button on the projector or the On 
button on the remote control. 
Note: When Direct Power On is enabled, power surges that occur after a power outage can 
cause the projector to turn on.
■Video...

Making Detailed Adjustments55
■Sleep Mode
Turn off this setting if you don’t want the projector to enter sleep mode. (Sleep mode 
shuts the projector off automatically when there is no video signal.) 
Select 
5min., 10min., or 30min. as the length of time before shutoff; decreasing the time 
conserves power and extends the life of the lamp. 
30min. is the default setting.
To turn the projector back on, press the Ppower button on the projector or the 
On 
button on the remote control.
■Child Lock
Lets you...

56Using WirelessHD
Using WirelessHD
You can use the included WirelessHD Transmitter (PowerLite Home Cinema 3010e only) to 
wirelessly stream HD content from a video device to the projector. 
Placing the WirelessHD Transmitter
Place the WirelessHD Transmitter so that the unit’s lights face the front of the projector. 
Make sure the transmitter is within 32 feet (10 meters) of the projector and is located in the 
same room. 
Note: The wireless transmission range may vary depending on the placement and size...

Using WirelessHD57
Setting Up a WirelessHD Connection
To prepare your device to work with the WirelessHD button, follow these steps:
1. Follow the instructions on the previous page and place the transmitter within range of the 
projector.
2. Plug the AC adapter into the transmitter and an electrical outlet.
3. Connect an HDMI cable to your video device and the HDMI port on the side of the 
WirelessHD Transmitter.
4. Turn on the power switch on the back of the transmitter.
5. Turn on your source device...

58Using HDMI Link
Using HDMI Link
When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you 
can control them using the HDMI Link control buttons on the projector’s remote control. 
This lets you use just one remote control to operate many commonly used features on all your 
devices.
In a typical configuration, your DVD player may be connected to the projector through an 
amplifier or home theater system. Even if the amplifier does not conform to the HDMI CEC 
standard, you can...

Using HDMI Link59
4. Set up your connected devices so their HDMI CEC-compatible functions are enabled. 
For details, refer to the device manufacturer’s documentation.
Changing HDMI Link Settings
1. Press the HDMI Link button on the projector’s remote control.
2. Select 
Device Connections. You see this screen:
3. Use the u and d arrow buttons to select the device you want to operate, then press 
Enter. Devices are listed by type (Player, Recorder, AV System, or Tuner) and by name, 
if the model number is...

60Maintenance
Maintenance
Your projector needs little maintenance. All you need to do on a regular basis is keep the lens 
clean. You also may need to clean the air filter to prevent overheating.
Warning: Before you clean any part of the projector, turn it off and unplug the power cord. Never 
open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages 
in the projector can injure you severely. Do not try to service this product yourself, except as 
specifically...