Epson Powerlite Cinema 200 Technical Specifications

							Epson PowerLite Cinema 200 Projector
1/04 Epson PowerLite Cinema 200 Projector - 11
Replacing the Lamp
The projection lamp lasts for up to 3000 hours (in low 
brightness mode) or 1700 hours (in high brightness mode). 
You can use the Info menu to check how long it’s been in use. 
It’s time to replace the lamp when:
❏The projected image gets darker or starts to deteriorate.
❏The projector’s warning light flashes red at half-second 
intervals.
❏The message 
Replace the lamp appears on the screen when 
you start projecting.
Note: Lamp life results will vary depending on the selected mode, 
environmental conditions, and usage. 
Contact your dealer or call Epson at (800) 873-7766 in the 
United States for a replacement lamp. Request part number 
V13H010L28. In Canada, call (800) 463-7766 for dealer 
referral.
Warning: Let the lamp cool fully before replacing it. In the unlikely 
event that the lamp has broken, small glass fragments may be 
present and should be removed carefully to avoid injury. 
The lamp component contains mercury. Please consult your state 
and local regulations regarding proper disposal or recycling, and do 
not place in the trash.
Caution: Never touch the lamp with your bare hands; the invisible 
residue left by the oil on your hands may shorten the lamp life. Use 
a cloth or glove to handle the new lamp.
Follow these steps to replace the lamp:
1. Turn off the projector and wait for the P power light to stop 
flashing, then unplug the power cord.
2. If the projector has been on, let it cool for about an hour.
3. Loosen the two screws securing the lamp cover (they don’t 
come all the way out), and then remove the cover.4. Loosen the two screws securing the lamp.
5. Grasp the lamp as shown and pull it straight out.
6. Fully insert the new lamp and tighten its screws.
Caution: Don’t touch the glass portion of the lamp assembly. 
Touching the glass could result in premature lamp failure.
7. Replace the cover and tighten its screws. (The projector 
won’t work if the lamp cover is open or loose.)
8. Reset the lamp usage timer, as described in the next section.
Resetting the Lamp Timer
After installing a new lamp, you need to reset the timer so the 
projector can keep track of how many hours it has been used. 
1. Press the 
Menu button on the projector or remote control.
2. Use the menu navigation buttons to open the 
Reset menu, 
then select 
Lamp-Hours Reset. 
3. When you see a confirmation prompt, highlight 
Yes and 
press the  button.
4. When you’re finished, press the 
Menu button to exit.
The lamp usage timer doesn’t register until you’ve used the 
lamp for at least 10 hours. 
						

							Epson PowerLite Cinema 200 Projector
12 - Epson PowerLite Cinema 200 Projector 1/04
Optional Accessories 
Epson provides the following optional accessories: 
You can purchase these accessories from your dealer, by calling 
Epson at (800) 873-7766, or by visiting the Epson Store  at 
www.epsonstore.com (U.S. sales only). In Canada, please call 
(800) 463-7766 for dealer referral. 
Related Documentation
CPD-17301EPSON PowerLite Cinema 200 
User’s Guide
CPD- 17303EPSON Extra Care  Home Service
warranty
CPD-17666Update slipsheet (explains how to
perform vertical stripe adjustment)
Note: Setup instructions are provided in the User’s Guide. There is 
no setup sheet.
Product Part number
Replacement lamp (ELPLP28) V13H010L28
Air filter replacement (ELPAF04) V13H134A04
Ceiling mount ELPHB01
Kensington security lock  ELPSL01
Projection screens:
50-inch portable screen 
60-inch portable pop-up screen
80-inch portable pop-up screenELPSC06
ELPSC07
ELPSC08
Macintosh adapter set (includes monitor 
adapter and desktop adapter)ELPAP01
S-video cable ELPSV01
SM
SM