Epson Powerlite 85 Multimedia Projector Users Guide

Using the Projector on a Network81
Enabling WPA Security
1. Press Menu. Highlight Network and then press Enter. 
2. Choose 
Network Configuration and press Enter. 
3. Highlight 
Security, then press Enter. You see the following 
screen: 
4. Press 
Enter to show the menu, then choose PSK and press Enter. 
5. Highlight the 
PSK (pre-shared key) text box and press Enter. Use 
the  buttons to select indivi dual letters; then press 
Enter to 
input a character. To add a blank space or to navigate backward...

82Using the Projector on a Network
Enabling Data Encryption from 
EMP NS Connection
When using the EMP NS Connection software, follow these steps to 
enable data encryption.
1. Click
 Set options on the main screen. 
2. Click the 
General Settings tab.
3. Select the 
Encrypt communications checkbox.
4. Click 
OK.
For more information, see the  EasyMP Operation Guide.
Using the EasyMP Software
Once you’ve set up your projector and computer for network 
projection, see the EasyMP Operation Guide  for...

Using the Projector on a Network83
Removing the Wireless LAN Module
Follow these steps to remove the module from your projector. 
1. If you’re running NS Connection, click 
Disconnect on the 
control bar.
 
2. Check the access light to make sure it isn’t flashing. 
3. Turn off the projector and unplug it.
4. Open the air filter cover by sliding the switch and pulling down  the cover.
5. Unscrew the module, then pull it out.
6. Close the air filter cover.
Click 
Disconnect
caution
Never remove the module...

84Using the Projector on a Network
Using Projector E-mail Alerts
When this feature is enabled, the projector sends you an e-mail alert if 
it has any problems. 
1. Press the 
Menu button on the remote control, select the 
Network menu, then press Enter. 
2. Choose 
Network Configuration and press Enter. 
3. Choose 
Mail, then press Enter. You see the following screen: 
4. Highlight 
On to receive email notifications, then press Enter.
5. Enter the IP address for the SMTP server for the projector. You...

Using the Projector on a Network85
When the selected problem or warning occurs, an e-mail message is 
sent to the specified notification addresses. The subject line of the 
e-mail is 
EPSON Projector. 
The e-mail includes the following information:
■Line 1: The name of the projector where the problem has 
occurred
■Line 2: The IP address of the projector where the problem has 
occurred
■Line 3: Details of the problem 
Using SNMP to Monitor the Projector
Network administrators can use SNMP (Simple...

86Using the Projector on a Network224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
5. For 
Priority Gateway, select Wired or Wireless.
6. If your network environment us es an AMX controller, select 
ON 
to allow the projector to be detected by AMX Device Discovery.
Using a Browser to Control the Projector
You can use a standard web browser to monitor and control the 
projector through the network.
1. Make sure that the projector is  set up for your network, as 
described on page 54....

87
5
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image, 
sound, and other features. This  chapter covers the following 
information: 
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Using the projector security features
■Customizing power and operation 

88Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to 
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the 
Menu button on the 
remote control or on the projector. 
You see a menu screen similar to the one below: 
The menus are listed on the left and the options available for the 
highlighted menu are shown on the right.
2. Use the  pointer buttons on the remote control (or the  navigational...

Fine-Tuning the Projector89
3. Once you’ve selected the menu, use the  pointer buttons to scroll through the list of options. (Some of the options may be 
grayed out or unavailable, depe nding on the selected source.)
4. After highlighting the option you want to adjust, use the  pointer buttons to change the setting. In some cases, you 
may have to press the 
Enter button to view a sub-screen for 
changing the setting. 
■Press the left or right arrow button to adjust a slider bar, then 
press 
Enter....

90Fine-Tuning the ProjectorTo restore all the projector settings to their factory-default values, 
select the 
Reset menu, highlight Reset All, and press Enter. 
Adjusting the Image 
You can use the Image menu to adjust
 the brightness, sharpness, color, 
tint, and contrast. 
1. Press the 
Menu button on the projecto r or remote control and 
select the 
Image menu. You see the Image menu screen. 
2. Use the  pointer buttons to highlight the desired option, then  adjust it as needed:
■Color Mode
Lets you...