Epson Powerlite 8300i Multimedia Projector Users Guide

Fine-tuning the Projector71
24 frames per second (fps) and convert it to 60 fps for a more 
natural appearance; or select 
Video to prevent frame conversion. 
Selecting 
OFF projects interlaced signals without converting them 
to progressive, which improves the look of images that contain a 
lot of movement. 
■BNC Sync Termination (in the Advanced2 menu)
This setting should normally be left OFF (for TTL input). If an 
analog (75-ohm) terminator is required, as for a switcher, change 
the setting to 
ON....

72Fine-tuning the Projectorthat is being used for communication with the computer. Turn 
off the projector and then turn it back on for the new setting to 
take effect. 
Miscellaneous Setup Options
■No-Signal Msg. (in the Setting menu) 
Selects a screen color or image to display when the projector is 
not receiving a signal. The logo setting displays an image that 
you previously transferred to the projector (see page 59).
■Prompt (in the Setting menu)
Turns off the identifying text that appears briefly...

Managing the Projector from a Remote Computer73
1
Managing the Projector from 
a Remote Computer
Your projector’s EasyManagement software lets you monitor and 
control your projector(s) from a remote computer. (The topics 
covered in this chapter are intended for use by network 
administrators.) 
■Use EMP Monitor to see your projectors’ status, switch image 
sources, and control basic settings.
■Use EMP NetworkManager to receive e-mail notifications 
alerting you to possible problems.
To use the...

74Managing the Projector from a Remote Computer
Installing the EasyManagement 
Software
The projector software CD-ROM includes the software you need to 
use the projector’s EMP Monitor and EMP Network Manager. 
System Requirements 
Before you install the software, make sure your computer meets these 
requirements: 
■Microsoft® Windows 98 SE, 2000, NT 4.0 (service pack 6a or 
later), Me, or XP
■IBM® compatible with at least a Pentium® MMX 166 MHz 
processor (Pentium II 233 MHz or better recommended)
■At...

Managing the Projector from a Remote Computer75
2. Click the  button to advance to the next screen.
3. If you want to receive e-mail notifications when projector 
problems occur, make sure the option to install 
EMP Network 
Manager 
is highlighted, then click the  button. Follow the 
instructions on the screen to finish installing it. 
4. If you want to be able to manage the projector remotely from this 
computer, select the option for 
EMP Monitor and install it the 
same way. 
5. When done installing...

76Managing the Projector from a Remote Computer
Connecting and Configuring the 
Projector
Before using the EMP software to manage your projector(s), you have 
have to connect each projector you want to monitor to your network 
and configure it with an appropriate IP address.
1. Connect the projector to your network using a commercially 
available 100baseTX or 10baseT network cable. 
Connect the cable to the ethernet port on the projector as shown.
2. Turn on the projector (see page 32). 
3. Press the...

Managing the Projector from a Remote Computer77
5. If your network does not assign addresses automatically, turn off 
DHCP and enter the projector’s IP Address, Subnet Mask, and 
Gateway Address, as needed. 
■To enter numbers using the remote control, press the Num 
button until it lights, then use the number keypad shown 
below. 
■To change the network addresses from the projector’s control 
panel, press the right and left arrow buttons to select the part 
of the address you want to enter, then use the...

78Managing the Projector from a Remote Computer
Using EMP Monitor
EMP Monitor lets you manage up to 64 projectors from a remote 
computer. This lets you easily turn the projectors on or off (together 
or individually), switch image sources, and check on their status.
Before using EMP Monitor, make sure you’ve installed the software as 
described on page 74. The computer you’re using to monitor the 
projector should already be connected to your network.
Opening and Closing EMP Monitor
To open the program,...

Managing the Projector from a Remote Computer79
2. Click Register projector as shown. 
You see this screen:
3. Click 
Auto detect to locate projectors currently operating on the 
network. Or click 
Manual registration and enter the projector’s 
name and network address. 
Any projectors found on the network are listed as shown below:
4. Select the projectors you want to add by clicking their name. 
Then click 
Add, and on the next screen click Close. 
Click here
note
If the name of a projector 
does not...

80Managing the Projector from a Remote ComputerYou see your registered projectors listed on the main EMP Monitor 
screen: 
Monitoring Your Projectors
The EMP Monitor screen lets you monitor your projectors using the 
Status, Video Source, and Error icons shown below. This lets you see 
which projectors are currently being used, from which source (or port) 
they are projecting an image, and if a problem occurs. 
For detailed status information, select the projector in question and 
click 
View details....