Epson Powerlite 737c Multimedia Projector Users Guide

							Welcome11
■If you still need help after checking this User’s Guide and the 
sources listed above, you can use the Epson PrivateLine Support 
service to get help fast. Call (800) 637-7661 and enter the PIN on 
the card in your Start Here kit. Or take advantage of Epson’s 
automated support services 24 hours a day. See page 166 for more 
information.
Registration and Warranty 
Your projector comes with a basic carry-in warranty as well as an 
international warranty that let you project with confidence anywhere 
in the world. For details, see page 184 and the warranty brochure 
included in your Start Here kit. 
In addition, for customers who register their projector, Epson offers 
free Extra Care
SM Road Service. In the unlikely event of an equipment 
failure, you won’t have to wait for your unit to be repaired. Instead, 
Epson will ship you a replacement unit anywhere in the United States 
or Canada, usually via overnight delivery. See the brochure in your 
Start Here kit for details.
To register, simply fill out the registration card included in your Start 
Here kit and mail it to Epson. Or you can register online at 
http://www.epson.com/webreg. Registering also lets you receive 
special updates on new accessories, products, and service. 
Banff-Toronto Users Guide.book  Page 11  Thursday, January 20, 2005  5:00 PM 
						

							12Welcome
Unpacking the Projector
After unpacking the projector, make sure you have all the parts shown 
below: 
Save all packaging in case you need to ship the projector. Always use 
the original packaging (or the equivalent) when you need to send the 
projector to another location. If you are moving the projector by 
hand, use the carrying case. See page 13 for ordering information, and 
page 150 for transportation instructions. 
Additional Components
Depending on how you plan to use the projector, you may need 
additional components:
■To receive an S-Video signal, you’ll need an S-Video cable. One 
may be provided with your video equipment, or you can purchase 
one from Epson; see page 13.
ProjectorRemote control and 
batteriesEasyMP software 
CD-ROM
Power cable
VGA computer cableUSB cable
802.11G/B wireless card
Audio adapter
Carrying case
Banff-Toronto Users Guide.book  Page 12  Thursday, January 20, 2005  5:00 PM 
						

							Welcome13
■To receive a component video signal from a VCR or other video 
device, you’ll need a component video cable. You can purchase 
one from Epson; see below.
■Some older PowerBooks® and Macintosh® desktop models may 
need the Macintosh desktop adapter set shown on page 39 
(available from Epson; see below.) Older iMac
® systems may need 
a special adapter to provide a VGA output port; see your 
computer dealer.
Optional Accessories 
To enhance your use of the projector, Epson provides the following 
optional accessories:  
You can purchase these accessories from an Epson authorized reseller. 
For product information and to find the nearest authorized reseller, 
please call 800-GO-EPSON (800-463-7766) or browse our catalog of 
products at www.epson.com, select the product you are interested in, 
Product Part number
Replacement lamp  V13H010L32
Air filter replacement set (2 filters) V13H134A08
ATA molded hardshell case 
Samsonite
® wheeled soft case
Notebook/projector soft shoulder bagELPKS42
ELPKS35-S
ELPKS43
Universal ceiling mount 
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channelELPMBUNI
ELPMBFCP
ELPMBSEC
ELPMBACC
Kensington
® security lock  ELPSL01
50-inch portable screen 
60-inch portable pop-up screen
80-inch portable pop-up screen
83.6-inch hanging pull-down screenELPSC06
ELPSC07
ELPSC08
ELPSC09
Macintosh adapter set  ELPAP01
Component video cable 
S-Video cable ELPKC19
ELPSV01
Distribution amplifier ELPDA01
Image presentation camera (ELPDC05) V12H162020
Banff-Toronto Users Guide.book  Page 13  Thursday, January 20, 2005  5:00 PM 
						

							14Welcomeand click “Where to Buy.” To purchase online, please visit the Epson 
Store
SM at www.epsonstore.com (U.S. sales only). In Canada, please 
call (800) 463-7766 for a reseller referral. 
Banff-Toronto Users Guide.book  Page 14  Thursday, January 20, 2005  5:00 PM 
						

							15
1
Displaying and Adjusting 
the Image
Whether you’re presenting from a computer or video equipment, 
you need to follow some basic steps to display your image on the 
screen. 
Follow the guidelines in this chapter for: 
■Positioning the projector
■Turning the projector on and selecting the image source
■Troubleshooting display problems
■Adjusting the image
■Turning off the projector
Banff-Toronto Users Guide.book  Page 15  Thursday, January 20, 2005  5:00 PM 
						

							16Displaying and Adjusting the Image
Positioning the Projector 
If the projector isn’t already installed in the room you’re using, you’ll 
probably want to place it on a table in front of the screen, as shown.  
This lets you stand in the front of the room, face the audience, and 
remain close enough to the equipment to be able to control it. Try to 
leave as much space as possible between the projector and the screen to 
get a good-size image. 
Use the figure below to help you determine placement. Image size 
increases with distance, but can vary depending on how you position 
the zoom ring and whether you’ve adjusted the image with other 
settings. 
Also keep these considerations in mind: 
■Place the projector on a sturdy, level surface.
■Make sure there is plenty of space for ventilation around and 
under the projector. Do not set the projector on top of anything 
that could block the vents under the projector. 
■Make sure the projector is within 10 feet of a grounded electrical 
outlet or extension cord. 
note
You can mount the projector 
on the ceiling, or place it 
behind a translucent screen 
for rear projection. See 
page 173 for details.
3.2 to 3.9 ft 6.6 to 7.9 ft 33.1 to 39.7 ft Distance from screen
 TBD
Banff-Toronto Users Guide.book  Page 16  Thursday, January 20, 2005  5:00 PM 
						

							Displaying and Adjusting the Image17
Ideally, you should place the projector directly in front of the center of 
the screen, facing it toward the screen squarely. The base of the lens 
should be at about the level of the bottom of the screen.  
If you place the projector below screen level, you’ll have to tilt it up by 
extending the front adjustable foot. This causes the image to become 
“keystone” shaped, but you can correct the distortion by pressing the 
buttons on the projector. See page24 for detailed information about 
correcting the image shape. 
For instructions on installing the projector in a permanent location, 
such as a theater or conference room, see page 173.note
After positioning the 
projector, you may want to 
connect a Kensington 
MicroSaver
® anti-theft 
device to the lock port on the 
projector’s left side. You can 
purchase this from Epson; 
see page 13. 
Screen
Projector
Banff-Toronto Users Guide.book  Page 17  Thursday, January 20, 2005  5:00 PM 
						

							18Displaying and Adjusting the Image
Projecting the Image
Make sure your projector and other equipment are set up as described 
on page 37. Then follow the instructions below to start the projector 
and display an image. 
Turning On the Projector
Turn on any connected computer or video equipment before starting 
the projector so it can automatically detect and display the image 
source. If you turn on the projector first, or have multiple pieces of 
connected equipment, you may have to select the image source 
manually (see page 19). 
Follow these steps to turn on the projector: 
1. Remove the lens cap. 
2. Plug one end of the power cable into the projector, and the other 
end into an electrical outlet.
The 
Power light comes on. 
note
To shut down the projector, 
see page 26. Shutting down 
the projector correctly 
prevents premature lamp 
failure and possible damage 
from overheating. 
Power light
Banff-Toronto Users Guide.book  Page 18  Thursday, January 20, 2005  5:00 PM 
						

							Displaying and Adjusting the Image19
3. Press the red PPower button on the remote control or on top of 
the projector. 
The projector beeps once and the 
Power light flashes green as the 
projector warms up, then an image begins to appear. When the 
Power light stops flashing and remains green, the projector is 
ready for use.  
4. If you’ve connected a Windows
®-based computer to the 
projector, you may see a New Hardware Wizard screen saying 
your computer has found a plug-and-play monitor; if so, click 
Cancel. 
5. If you are prompted to enter a password, see page 114.
Selecting the Image Source
Selecting the image source lets you switch between images input from 
different pieces of connected equipment (such as a computer or DVD 
player).  
If you don’t see the image you want, press the 
Source Search button 
on the projector or the 
Search button on the remote control until 
you see the image you want to project. 
You can also use the 
Source buttons on the remote control to switch 
between devices connected to the ports identified on each button, or 
select EasyMP to project wirelessly or from a memory card.
TM 
warning
Never look into the lens 
when the lamp is on. This 
can damage your eyes, and is 
especially dangerous for 
children.
note
To focus and adjust the 
image, see page 23. If a 
projected image fails to 
appear, see page 20 for help.
Banff-Toronto Users Guide.book  Page 19  Thursday, January 20, 2005  5:00 PM 
						

							20Displaying and Adjusting the Image
Troubleshooting Display Problems
Follow these guidelines if you’re having trouble displaying an image. 
You Can’t Project an Image
If you don’t see the image you are trying to project, try the following: 
■Make sure the cables are connected correctly, as described 
beginning on page 37.
■Make sure the Power light is green and not flashing and the lens 
cap is off. 
■If you’ve connected more than one computer and/or video source, 
you may need to press the 
Source Search button on the 
projector’s control panel or 
Search button on the remote control 
to select the correct source. (Allow a few seconds for the projector 
to sync up after pressing the button.)
■If you’re using a PC notebook, press the function key on your 
keyboard that lets you display on an external monitor. It may be 
labeled 
CRT/LCD or have an icon such as  . You may have to 
hold down the 
Fn key while pressing it. Allow a few seconds for 
the projector to sync up after changing the setting. 
The Projector and Notebook Don’t Display the 
Same Image
If you’re projecting from a notebook, and you can’t see your image on 
the projection screen and on your computer at the same time, follow 
these guidelines.
If you’re using a PC notebook:
■On most systems, there’s a function key that lets you toggle 
between the LCD screen and the projector, or display on both at 
the same time. It may be labeled 
CRT/LCD or have an icon such as 
. You may have to hold down the 
Fn key while pressing it. 
Allow a few seconds for the projector to sync up after changing 
the setting. 
Banff-Toronto Users Guide.book  Page 20  Thursday, January 20, 2005  5:00 PM