Epson Powerlite 737c Multimedia Projector Users Guide

							Presenting from a Memory Card, Digital Camera, or External Drive101
Transferring Your Scenario to a 
Memory Card
Once your scenario is saved, you can transfer it to a memory card or 
USB storage device. You can use any of the following standard cards. 
Most require a PC card adapter to allow insertion into the projector 
(check with your computer dealer to purchase a PC card adapter). 
Be sure to use the transfer process described below to ensure that the 
scenario plays properly: 
1. Insert the memory card in your computer’s PCMCIA slot or 
connect the USB storage device.
2. Start EMP SlideMaker 2 (see page 94).
3. Use the navigation tools in the folders window to locate the 
scenario file you want to review. Click the file, then click 
File > 
Open
 to open the scenario.
4. From the Scenario Option(s) menu, choose 
Send Scenario. You 
see a drive selection window:
5. Choose the drive where your card is located and click 
OK. 
6. Click 
OK again to confirm. Your scenario is transferred to the 
card.
■CompactFlash™■Memory Stick™■SD™ (Secure Digital
■SmartMedia™■MicroDrive™■MMC (Multimedia)
■ATA flash (does not require a PC card adapter)note
You have to save the 
scenario on your computer’s 
hard drive before 
transferring it. Don’t use 
Windows to copy the 
scenario to your memory 
card, or it may not play 
properly.
You must insert the memory 
card in your computer’s 
PCMCIA slot (or connect 
the USB device) before you 
select 
Send Scenario from 
the Scenario Option(s) 
menu. If you don’t, you 
won’t be able to see the 
card’s drive in the drive 
selection window. If this 
happens, close and restart 
EMP SlideMaker 2.
Select your memory 
card drive
Banff-Toronto Users Guide.book  Page 101  Thursday, January 20, 2005  5:00 PM 
						

							102Presenting from a Memory Card, Digital Camera, or External DriveOnce the scenario is transferred, you see this message about your 
scenario’s autorun setting:
 
The autorun setting means that the scenario will start playing 
whenever the projector is turned on (with the memory card in the 
projector).
7. Do one of the following:
■If you don’t want the scenario to run automatically, click 
Cancel
. Skip to step 11 to remove the card and insert it in 
the projector.
■If you want it to run automatically, click OK and continue 
with the following instructions.
You see the Edit Autorun window:
8. To set a scenario to run automatically, select it from the list on the 
left side of the screen and use the   arrow button to move it to 
the list on the right. 
9. Click the 
Revive box if you want your scenario to repeat 
continuously. Clear the checkbox if you want it to play only once.
note
If more than one scenario is 
set to run automatically, 
they will play in the order 
listed on this screen.
Banff-Toronto Users Guide.book  Page 102  Thursday, January 20, 2005  5:00 PM 
						

							Presenting from a Memory Card, Digital Camera, or External Drive103
10. When done, click OK.
11. Remove the card from your computer or disconnect the USB 
device. See your computer’s documentation if you need 
instructions on removing the card. If you’re using Windows 2000 
or Me, you may first need to click an icon to stop or disconnect 
the card
. 
Presenting Scenarios
Before you begin, insert the memory card containing the scenario into 
your projector, as described on page 86. 
The follow these steps to present your scenario:
1. Turn on the projector, if it’s not already on. 
■If your scenario is set to autorun, it will start as soon as the 
projector warms up.
■If your scenario is not set to autorun, you need to start it 
manually. Continue with the following steps.
2. Select EasyMP as the source by pressing the 
EasyMP button on 
the remote control. You see a screen like the one below. 
JPEG files are displayed as thumbnails. Other files or folders are 
displayed as icons. A   scenario icon identifies a scenario file.
note
You cannot have a digital 
camera connected while the 
memory card is inserted. If 
you do, neither the camera 
nor the card will function 
with your projector’s 
software.
Banff-Toronto Users Guide.book  Page 103  Thursday, January 20, 2005  5:00 PM 
						

							104Presenting from a Memory Card, Digital Camera, or External Drive3. Use the  pointer button on the remote control to highlight 
your   scenario file and press 
Enter. A drop-down menu 
appears under the scenario.
4. Use the  pointer button to select 
Play Scenario and press 
Enter. In a moment, your scenario begins playing. 
5. When you’re done with your presentation, use the  pointer 
button to highlight 
EJECT in the upper right corner of the screen, 
and press 
Enter on the remote control. When you see a message 
asking you to insert a LAN card or memory card, it’s safe to 
remove your memory card (see page 86 for instructions).
Controlling Your Scenario
While your scenario is running, use the remote control as follows:
■Press Enter or  Page down to display the next slide or image, 
or to begin playing a movie. 
■Press  Page up to display the previous slide or image, or to 
replay a movie.
■Press the appropriate side of the  pointer button to rotate a 
slide or image on the screen.
■To exit the scenario at any point, press the Esc button. Press the 
Enter button to confirm that you want to exit. 
note
Your files may take up more 
than one screen. If so, use the 
Page up and Page down 
buttons on the remote 
control to view all your files.
note
Even if your scenario is set to 
change slides automatically, 
you can still change slides 
manually as described here.
Banff-Toronto Users Guide.book  Page 104  Thursday, January 20, 2005  5:00 PM 
						

							Presenting from a Memory Card, Digital Camera, or External Drive105
Editing Your Scenario on the Projector
You can modify your scenario using EasyMP on the projector. This 
lets you make last-minute changes, such as changing the order of your 
slides or hiding individual slides. These changes are not permanently 
saved with the scenario, but remain in effect only as long as the card is 
in the projector and the projector is turned on. 
1. Highlight the   scenario you want to edit, then press 
Enter. 
2. From the drop-down menu, select 
Edit Scenario. You see 
thumbnail images of the slides in your scenario:
3. To move a slide, select the slide you want to move and press 
Enter. From the drop-down menu, select Move Files. A yellow 
line (or “I-beam”) appears beside the slide.
Use the  pointer button to move the I-beam where you want to 
insert the slide and press 
Enter. The slide moves to the new 
position.
4. To hide a slide, highlight the slide you want to hide and press 
Enter. From the drop-down menu, select Show/Hide. 
If you change your mind and want to display the slide again, 
repeat this step to make the slide visible.
5. When done, highlight the 
OK button and press Enter. 
Indicates 
slide to be 
moved
Banff-Toronto Users Guide.book  Page 105  Thursday, January 20, 2005  5:00 PM 
						

							106Presenting from a Memory Card, Digital Camera, or External Drive
Supported File Formats
The following file types may be projected from a memory card, digital 
camera, external hard drive, or flash memory drive: 
JPEG files with the extension “.jpeg” and “.mpeg” can’t be projected. 
Rename or save files as “.jpg” or “.mpg.” JPEG files with high 
compression will not look good. Movie files may not look as good 
from media with a slow access speed. 
File Type Extension Notes
Scenario .sit These are scenario files created using the 
EMP SlideMaker 2 program that is included 
with the projector.
Graphics .bmp Only 24-bit color files can be played.
.gif Images with a resolution greater than 1024 
× 768 cannot be projected.
.jpg  Projection is not possible for CMYK color 
formats, progressive formats, and images 
with a resolution in excess of 2560 × 1920. 
.png Projection is not possible for images with a 
resolution in excess of 2560 × 1920.
Movie .mpg MPEG2-PS
If the movie exceeds a maximum size of 
720 × 576, or is not in the same form as a 
DVD (sequence header arranged for each 
GOP) it cannot be played back.
The reproducible audio format is MPEG-1 
Layer 2. Linear PCM and AC- 3 audio cannot 
be played back.
DPOF .mrk For DPOF version 1.10, only files named 
AUTPLAYx.mrk (where x is a number 
between 0 and 9) can be projected.
Banff-Toronto Users Guide.book  Page 106  Thursday, January 20, 2005  5:00 PM 
						

							107
1
Fine-Tuning the Projector
You can use the projector’s on-screen menus to adjust the image, 
sound, and other features. This chapter covers the following 
information: 
■Using the menu system
■Adjusting the image
■Adjusting signal settings
■Customizing projector features
■Using the projector security features
■Customizing power and operation
Banff-Toronto Users Guide.book  Page 107  Thursday, January 20, 2005  5:00 PM 
						

							108Fine-Tuning the Projector
Using the Menu System
You can use the remote control or the projector’s control panel to 
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the 
Menu button on the 
remote control or on the projector.  
You see a menu screen similar to the one below:
The menus are listed on the left and the options available for the 
highlighted menu are shown on the right.
2. Use the  pointer button on the remote control (or the arrow 
buttons on the projector) to scroll through the menu list. When 
you’ve highlighted the desired menu, press the 
Enter button to 
select it. 
3. Once you’ve selected the menu, use the  pointer button to 
scroll through the list of options. (Some of the options may be 
grayed out or unavailable, depending on the selected source.)
Menu list
Options
Banff-Toronto Users Guide.book  Page 108  Thursday, January 20, 2005  5:00 PM 
						

							Fine-Tuning the Projector109
4. After highlighting the option you want to adjust, use the 
pointer button to change the setting. In some cases, you may 
have to press the 
Enter button to view a sub-screen for changing 
the setting. 
■Press the left or right side of the  pointer button to adjust
a slider bar.
■To select from two or more settings, use the  pointer 
button to highlight the desired setting and press 
Enter. 
5. After changing the settings, press the 
Esc button to save your 
changes and return to the previous menu (or press it repeatedly to 
exit the menu system). 
You can also press the 
Menu button to exit. 
Restoring the Default Settings 
You can use the menu system’s Reset options to restore the factory-
default settings for all the settings listed in a specific menu, or all the 
settings in all menus.
To restore the settings in a specific menu, enter the menu whose 
settings you want to change, select 
Reset, and confirm as needed. 
(The example below shows how to reset the Image menu.) 
To restore all the projector settings to their factory-default values, 
select the 
Reset menu, highlight All Reset, and press Enter. 
+
-
ONONOFFOFF
Reset settings
for current menu
Reset settings for
all menus
note
When you select Reset All 
in the Reset menu, it does 
not reset the Computer 
Input, Video Signal, User’s 
Logo, Language, and Lamp 
settings.
Banff-Toronto Users Guide.book  Page 109  Thursday, January 20, 2005  5:00 PM 
						

							110Fine-Tuning the Projector
Adjusting the Image 
You can use the Image menu to adjust the brightness, sharpness, color, 
tint, and contrast. 
1. Press the 
Menu button on the projector or remote control and 
select the 
Image menu. You see the Image menu screen. 
2. Use the  pointer button to highlight the desired option, then 
adjust it as needed:
■Color Mode
Lets you quickly adjust the color and brightness for various 
environments. Use either the remote control or the 
Color 
Mode
 setting in the Image menu. You can save a different 
setting for each source. Select from these settings:
Dynamic: For increased brightness in bright rooms (the 
default for non-computer display).
Presentation: For computer presentations (the default when 
projecting from a computer with analog video).
Theatre: For optimizing movie images with increased 
contrast. 
Living Room: For increased brightness when playing video 
games or watching TV in a bright room.
sRGB: For matching the color palette of standard sRGB 
computer displays.
Blackboard: For projecting accurate colors on a green 
chalkboard (adjusts the white point).
Banff-Toronto Users Guide.book  Page 110  Thursday, January 20, 2005  5:00 PM