Epson Powerlite 7200 Users Guide

							Using the Software
113
Creating a User Logo
You can create or edit a logo from the Projector Setting dialog box, 
then save it to a file on your hard disk or download it to the projector.
1. Click User’s Logo on the Projector Setting dialog box. The 
User’s Logo Setting window appears.
5300.book  Page 113  Tuesday, April 13, 1999  4:19 PM 
						

							4  •  Using the ELP Link III Software             114
2. Click the Edit button. The following window appears.
3. Click the Open the File icon to locate and open a bitmap (or 
TIFF, JPG, PSO) file. The selected image appears in the display 
area.
4. To crop the image, click the Select Area button and position the 
crop marks. Click OK to accept the changes. The User’s Logo 
window reappears.
5. To increase or decrease the size at which the logo displays, select a 
zoom percentage from the Zoom list box.
6. Click the Save button to save your logo to your hard disk. The 
Save As dialog box appears.
Note: You must save logo files with the extension .lgo.
5300.book  Page 114  Tuesday, April 13, 1999  4:19 PM 
						

							Using the Software
115
7. To download a logo file to the projector, click the Download 
button and follow the directions on the screen.
Note: To change the logo that appears in the display area of the User’s 
Logo Setting window, click the File icon to locate and open a different 
file.
8. Click Close to return to the Projector Setting dialog box.
5300.book  Page 115  Tuesday, April 13, 1999  4:19 PM 
						

							4  •  Using the ELP Link III Software             116
5300.book  Page 116  Tuesday, April 13, 1999  4:19 PM 
						

							117
5Maintenance
Y
our projector needs little maintenance. You should keep the lens 
clean because any dirt or smears appear on the screen. You also need to 
periodically clean the air filter at the bottom of the projector. A 
clogged air filter can block ventilation needed to cool the projector and 
keep it from overheating. 
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified service 
person.
5300.book  Page 117  Tuesday, April 13, 1999  4:19 PM 
						

							5  •  Maintenance             118
F
Warning: Before you clean any part of the projector, turn off the projector 
and unplug the power cord. Never open any cover on the projector, except 
the lamp and filter covers. Dangerous electrical voltages in the projector 
can injure you severely. Do not try to service this product yourself, except as 
specifically explained in this User’s Guide. Refer all other servicing to 
qualified service personnel.
Cleaning the Lens 
Clean the lens whenever you notice dirt or dust on the surface. Lightly 
wipe the lens surface with a soft, dry, lint-free cloth. To remove dirt or 
smears on the lens, moisten a soft cloth with an alcohol-based cleaner 
and gently wipe the lens surface.
Cleaning the Projector Case 
To clean the projector case, first unplug the power cord. To remove 
dirt or dust, wipe the case with a soft, dry, lint-free cloth. To remove 
stubborn dirt or stains, moisten a soft cloth with water and a neutral 
detergent. Then wipe the case. 
Do not use alcohol, benzene, thinner, or other chemical detergents. 
These can cause the case to warp.
5300.book  Page 118  Tuesday, April 13, 1999  4:19 PM 
						

							Cleaning the Air Filter
119
Cleaning the Air Filter 
Clean the air filter at the bottom of the projector after every 100 hours 
of use. If it is not cleaned periodically, it can become clogged with 
dust, preventing proper ventilation. This can cause overheating and 
damage the projector. To clean the air filter, follow these steps:
1. Turn off the projector and unplug the power cable.
2. Turn the projector on its side so that the handle is on top and you 
can access the filter easily.
Note: Standing the projector with the handle at the top keeps dust 
from getting inside the projector housing.
3. Pull up on the filter cover tab to release the filter cover. Remove 
the cover.
5300.book  Page 119  Tuesday, April 13, 1999  4:19 PM 
						

							5  •  Maintenance             120
4. The filter is attached to the inside of the filter cover. It is 
recommended that you use a small vacuum cleaner designed for 
computers and other office equipment to clean the filter. If you 
don’t have one, use a dry, lint-free cloth. 
If the dirt is difficult to remove or if the filter is torn, replace it. 
Contact your dealer or call EPSON Accessories at (800) 873-7766 
in the United States and Canada to obtain a new one. 
5. Replace the filter cover when you’re done.
Replacing the Lamp 
  
The projection lamp typically lasts for about 2000 hours of use. It is 
time to replace the lamp when:
l
The projected image gets darker or starts to deteriorate.
l
The projection lamp light is either red, or flashing orange and red 
alternately. 
l
The message LAMP REPLACE appears on the screen when the 
projection lamp comes on. 
Contact your dealer or call EPSON Accessories at (800) 873-7766 in 
the United States and Canada for a replacement lamp. Request part 
number ELPLP05.
F
Warning: Let the lamp cool before replacing it. Also, do not touch the glass 
portion of the lamp assembly. Touching the glass portion of the lamp will 
result in premature lamp failure.   
5300.book  Page 120  Tuesday, April 13, 1999  4:19 PM 
						

							Replacing the Lamp
121
1. Turn off the projector and unplug the power cable.
2. Turn the projector over so you can access the lamp cover.
3. Use a screwdriver, coin, or similar object to loosen the two 
retaining screws on the lamp cover. When the screws are loose, lift 
off the lamp cover. (You cannot remove these screws from the 
cover.
)
5300.book  Page 121  Tuesday, April 13, 1999  4:19 PM 
						

							5  •  Maintenance             122
4. Use a screwdriver, coin, or similar object to loosen the two screws 
holding the lamp unit in place. (You cannot remove these screws.) 
5. Lift up the handle and pull out the lamp unit.
5300.book  Page 122  Tuesday, April 13, 1999  4:19 PM