Epson Powerlite 62c Multimedia Projector Users Guide

							
Fine-tuning the Projector61
3. Press Enter. Then use the  pointer button (or up and down 
arrow buttons) and the 
Enter button to set the following options:
■Keystone
Adjusts a distorted image from a trapezoid shape to 
rectangular. 
■Auto Keystone
Automatically adjusts a distorted image from a trapezoid 
shape to rectangular when the projector’s foot is extended or 
retracted. (Not available when  you’re projecting from the 
ceiling or using rear projection.) Select 
ON or OFF.
■Operation Lock
When turned on, this function disables all projector buttons 
except the  P
Power button. Changes to this setting take 
effect after you restart the projector. (After you turn off the 
projector, wait for the  Ppower light to turn a steady orange 
before turning it on again.)
■Pointer Shape
Lets you select from three different pointer shapes. The 
Password Protect function mu st be cancelled first. See 
page 68.
■Brightness Control
Select Low lamp brightness when the  projection is too bright 
for the room. The 
Low setting also reduces electricity 
consumption and fan noise. Select 
High to project the 
maximum brightness. (Also check the 
Brightness setting in 
the Image menu; see page 56.)
■Volume
Adjusts the volume for the projector’s speaker.
4. When you’re finished, press 
Esc or Menu.
note
To cancel the Operation 
Lock function from the 
projector, press the 
Enter 
button for about seven 
seconds. 
						

							
62Fine-tuning the Projector
Selecting Projector Setup Options
Use the Extended menu to customize the way you set up the 
projector. You can configure the projector for rear and/or ceiling 
projection, change the language for the menus and messages, set the 
screen background color, capture and store a custom image or logo for 
the startup screen, and set up the projector for network use.
1. Press the 
Menu button.
2. Select the 
Extended menu. You see the features and their settings 
on the right side:
3. Press 
Enter. Then use the  pointer button (or the up and down 
arrow buttons) and the 
Enter button to set the following options:
■Display
Message: 
Lets you turn screen messages on or off.
Background Color: Sets the screen background to Black, 
Blue, or Logo when the A/V Mute button is pressed.
Startup Screen: Enables or disables display of the startup 
screen when the projector is turned on.
■User’s Logo
Turn on to display the image or logo you have captured 
whenever the projector is turned on. See page 66 for more 
information.
note
The Startup Screen option 
cannot be turned off if the 
User’s Logo Protect feature 
has been turned on. See 
page 68. 
						

							
Fine-tuning the Projector63
■Projection
Front:
 Projector is in front of the screen.
Front/Ceiling: Projector is in front of the screen, mounted 
upside-down from the ceiling.
Rear: Projector is behind the screen.
Rear/Ceiling: Projector is behind the screen, mounted 
upside-down from the ceiling.
■Operation
Direct Power:
 When this feature is enabled, projection starts 
as soon as you plug in the power cord. You don’t have to 
press the  P
Power button.
Sleep Mode: When Sleep Mode is on, the projector turns 
off the lamp if it has not received any input signals for 30 
minutes.
High Altitude Mode: When using the projector at an 
altitude above 4,921 feet, turn this setting on to ensure that 
the internal temperature of the projector is regulated 
properly. Turn this setting off for lower elevations.
■Standby Mode: Set to Network ON to monitor your 
projector over a network and perform other network 
functions when the projector is in standby mode.
■COM Port
Turn on USB only if you’re controlling the projector from a 
computer with the EMP Link 21L software. This software 
can be downloaded from the Epson website at 
support.epson.com. (You must turn the projector off and 
then on again to use the new setting.)
■Language
Select the language to be used for the projector menus.
4. When you’re finished, press 
Esc or Menu.
note
When Direct Power 
is turned on, press the 
P  
Power button to turn 
the projector off, wait until 
the  Ppower light turns a 
steady orange, then unplug 
the power cord.
 
  
						

							
64Fine-tuning the Projector
Viewing Lamp Usage and Other 
Information
Use the Info menu to view information about the display settings of 
your computer and the number of hours the lamp has been used.
1. Press the 
Menu button and select the Info menu. You see one of 
the following menus:
■Lamp Hours
Displays the number of hours the lamp has been used. The 
life span of the lamp ranges from about 2000 hours in 
High 
brightness mode to about 3000 hours in 
Low brightness 
mode. If the number shown  is close to 2000 or the 
information is displayed in red, make sure you have a spare 
lamp handy.
note
You can make changes to 
many of the signal settings on 
the Signal menu. See page 58 
for details.
note
The lamp usage timer doesn’t 
register until you’ve used the 
lamp for at least 10 hours.
Computer (analog RGB, digital RGB, RGB 
Video/Component video, YCbCr, YPbPr)
Video (Composite video, S-Video) 
						

							
Fine-tuning the Projector65
■Source
Displays the input source currently being projected.
■Input Signal (computer, RGB video, and component video)
Displays the input signal setting.
■Resolution (computer, RGB video,  and component video)
Displays the input resolution.
■Video Signal (composite and S-Video)
Displays the video signal format.
■Refresh Rate (computer, RGB video, and component video)
Displays the refresh rate.
■Sync Info (computer, RGB video, and component video)
Provides information that may be needed by the service 
technician.
2. When you’re finished, press 
Esc or Menu.
Using the Projector’s Security Features
To prevent unauthorized use of the projector, you can do the 
following:
■Create an identifying user logo th at is displayed at startup and/or 
when the 
A/V Mute button is pressed
■Assign a password; this can be disabled for a set period if you want 
to loan the projector to someone
■Disable the projector’s buttons; this is useful, for example, if 
you’re projecting in  a classroom and you want to ensure that no 
one touches the projector’s buttons while you’re using the remote 
control
If you create a user’s logo for the projector, you can lock the logo on so 
it is displayed as the startup screen and/or AV/Mute screen. 
Unauthorized users cannot turn it of f or change it. This feature is 
intended to discourage theft and provides a way to identify the 
projector should it be stolen.  
						

							
66Fine-tuning the ProjectorIf you assign the projector a passwor
d, a screen appears requesting the 
password whenever the projector is turned on. If you enter the 
password incorrectly three times in succession, the projector’s 
operation is locked and you’ll need to disconnect the power cord, then 
reconnect it to redisplay the passwo rd screen. If an incorrect password 
is entered 30 times in a row, the projector is locked and you’ll need to 
contact Epson to unlock it. See “W here To Get Help” on page 95.
If someone else will be using the projector for awhile but you want to 
make sure that person returns it by  a certain time, you can temporarily 
disable the password for a set period. When that time has elapsed, the 
password is reactivated and must be  entered before the projector can 
be used.
When you enable the Operation Lock feature, all of the projector’s 
buttons are disabled except the  P
 Power button.
Creating Your Own Screen Logo
You can transfer any image on your computer to the projector, and 
then use it as the startup screen and/or the screen that is displayed 
when you press the A/V Mute button. The image can be a company 
logo, slogan, photograph, or any other image you want to use. The 
projector considers this image the “User’s Logo.” 
Follow these steps to capture the image and transfer it to the projector:
1. Display the image you want to use on the projector. You can use 
an image from either a computer  or video source, such as a VCR. 
2. Press the 
Menu button and select the Extended menu.
note
If you should happen to 
enable the password before 
you set one and you see the 
prompt to enter the 
password, enter the default 
password 0000 to proceed.
note
If the User’s Logo Protect 
function is 
ON, you see a 
message that th e logo cannot 
be recorded. You’ll need to 
disable the User’s Logo 
Protect function before you 
can create or change the 
User’s Logo. See page 68. 
						

							
Fine-tuning the Projector67
3. Use the  pointer button (or the down arrow button) and press 
Enter to select User’s Logo.
4. When you see a message asking if you want to use the present  image as a user’s logo, select 
Yes and press Enter. A selection box 
displays over the image.
5. Use the  pointer button on the remote control or the arrow  buttons on the projector to select the area of the image you want 
to use. Once you have selected the area, press 
Enter.
6. When you see the message 
Select this image?, choose Yes and 
press 
Enter. If you want to change the area selected, select No, 
press
 Enter and repeat steps 5 and 6. 
7. When you see this screen, select  a zoom rate (display size), and 
then press 
Enter. 
8. When you see the message 
Save image as user’s logo?, select 
Yes and press Enter. Saving the logo takes a few moments. Do 
not use the projector or other so urces (computer, video, etc.) 
while the logo is being saved.
9. When you see the message 
Completed, press Esc.
10. To display the logo as the background screen when the A/V Mute  button is press, select the 
Display menu and press Enter.
11. Select 
Background Color and press Enter. Then select Logo and 
press 
Enter.
12. When you’re finished, press 
Menu to exit the menus. 
note
The default setting for the 
Startup Screen option in 
the 
Display menu is ON. If 
the 
Startup Screen is set to 
OFF, the logo will not 
display at startup.
If the User’s Logo Protect 
function has been set to 
ON, 
the 
Background Color 
setting cannot be changed. 
You need to turn the protect 
function off first. See page 68 
for details.
Once you’ve saved a user’s 
logo, you cannot reset the logo 
setting to its factory default 
(no logo). 
						

							
68Fine-tuning the Projector
Setting a Password 
1. Press the Freeze button on the remote control for about 7 seconds 
until you see the Password Protect menu:
2. Select 
Password and press Enter. You see the message Change 
the password?
 
3. Select 
Yes and press Enter.
4. Hold down the 
Num key on the remote control and use the 
numeric keypad to enter a 4-digit password. 
The password will be displayed as 
****. After you enter the last 
digit, a confirmation screen appears. Enter the password again.
5. After you finish setting the password, press the 
Esc button to 
return to the Password Protect menu.
Make a note of the password and keep it in a safe place in case you 
forget it. 
Turning On the Passwor d and User’s Logo
1. Press the Freeze button on the remote control for about 7 
seconds until you see the Password Protect menu.
2. To enable the password, select 
Power ON Protect and press 
Enter. Select ON then press Esc. 
3. If you want to disable the  password temporarily, select 
Timer and 
press 
Enter. Then hold down the Num button while you use the 
numeric keypad to enter the number of hours (from 0 to 9999) 
that you want the password feature disabled. If you want the 
projector to request the password every time it is turned on, set 
the timer to 
0H. 
note
If a password has already 
been set, you see the 
Password Protect Release 
screen. See “Starting the 
Projector with a Password” 
on page 69.
Use these butt ons like a 
numeric keypad to enter 
the password
Hold down this button to 
activate the numeric 
keypad 
						

							
Fine-tuning the Projector69
The countdown for the elapsed time begins as soon as you close 
the Password Protect menu. (You can check the elapsed time in 
this menu next to 
Time elapsed.)
4. To enable your screen logo, select 
User’s Logo Protect and press 
Enter. Select ON and press Enter. 
When this feature is on the logo appears whenever the projector is 
turned on (if the 
Startup Screen is enabled in the Extended 
menu; see page 62) and as the A/V  Mute screen (if you selected 
the 
Logo as the Background Color in the Extended menu). 
None of the User’s Logo features can be changed when the User’s 
Logo Protect function is enabled.
5. Press 
Menu to close the Password Protect menu.
If you lose the remote control, you will not be able to enter the 
password, so keep the remote control in a safe place at all times. 
When the period defined in the Time-elapsed setting has passed, and 
the password is entered correctly, th e elapsed time will be reset to 
0 
and the countdown will start again. Remember to disable or change 
this setting when you need to.
Starting the Projec tor with a Password
When the password function is enabled, you see this screen when you 
turn on the projector:
Press down the 
Num button on the remote control as you use the 
numeric keypad buttons to enter the password. Once you have 
entered the password correctly, th e password screen closes, and 
projection begins. 
						

							
70Fine-tuning the ProjectorIf the password is not correct, you see the message 
Wrong password. 
Please try again.
 If you enter an incorrect password three times in 
succession, you see the message 
The projector’s operation will be 
locked. Request code xxxxx
 and the projector switches to standby 
mode for approximately 5 minutes. Write down the request code. 
Then disconnect the projector’s powe r cord from the electrical outlet, 
reconnect it, and turn the projector back on. 
When you see the Password Protect Release screen again, you can try 
to enter the correct password.
If you have forgotten the password, contact Epson with the request 
code number that appears in the Password Protect Release screen for 
assistance. See “Where To Get Help” on page 95.
If you enter an incorrect password 30 times in succession, the 
projector remains locked and you must contact Epson to unlock it. 
Disabling the Projector’s Buttons
When you enable the Operation Lo ck function, all the projector’s 
buttons are disabled except for the  P 
Power button.
1. Press the 
Menu button.
2. Select the 
Settings menu and press Enter.
3. Use the  pointer button (or up and down arrow buttons) to  select 
Operation Lock and press the Enter button.
4. Select 
ON and press Enter.
5. Select 
Yes and press Enter to confirm the setting.
6. Press the 
Menu button.
note
To cancel Operation Lock, 
press the projector’s 
Enter 
button for seven seconds.