Epson Powerlite 6100i Multimedia Projector Users Guide

Welcome11
Unpacking the Projector
After unpacking the projector, make sure you have all the parts 
shown below: 
Save all packaging in case you need to ship the projector. Always use 
the original packaging (or the equivalent) when you need to send the 
projector to another location. If you are moving the projector by 
hand, use a carrying case (either an Epson case or something similar, 
such as a well-padded case). See page 12 for ordering information, and 
page 95 for transportation instructions....

12Welcome
Optional Accessories 
To enhance your use of the projector, Epson provides the following 
optional accessories: 
You can purchase these accessories from an Epson authorized reseller. 
To find the nearest reseller, call 800-GO-EPSON (800-463-7766). 
Or you can purchase online at www.epsonstore.com (U.S. sales) or 
www.epson.ca (Canadian sales). 
Product Part number
Replacement lamp V13H010L37
High efficient air filter (standard)
Smoke filterV13H134A11
V13H134A12
Ceiling mount
Suspension adapter...

1
13
1
Setting Up the Projector
This chapter gives you basic information on setting up the projector: 
where to position it and how to connect it to a video source (such as a 
VCR or DVD player) or to a notebook or desktop computer. 
Follow the instructions in this chapter on:
■Positioning the projector
■Connecting to video equipment
■Connecting to a computer
■Connecting an external monitor
■Playing sound through the projector 

14Setting Up the Projector
Positioning the Projector
If you’re setting up the projector yourself and it isn’t already installed 
in the classroom or conference room you’re using, you’ll probably 
want to place it on a table in front of the screen, as shown on 
page 15.low
This lets you stand in the front of the room, face the audience, and 
remain close enough to the equipment to be able to control it. Try to 
leave as much space as possible between the projector and the screen to 
get a good-size image....

Setting Up the Projector15
Ideally, you should place the projector directly in front of the center of 
the screen, facing it toward the screen squarely. The lens should be at 
about the level of the bottom of the screen. 
If you place the projector below screen level, you’ll have to tilt it up by 
extending its feet. This causes the image to become “keystone” shaped, 
but you can correct the distortion by pressing the   or   buttons 
on the projector. See page 36 for detailed information about...

16Setting Up the Projector
Connecting to Video Equipment 
You can connect up to four video sources to the projector at the same 
time. Before starting, look at your video equipment to determine its 
available video-output connections: 
■If your video player has a yellow RCA-style video output 
connector, see “Connecting a Composite Video Source” on 
page 17.
■If your video player has an S-Video connector, see “Connecting 
an S-Video Source” on page 18.
■If your video player has a component video port...

Setting Up the Projector17
Connecting a Composite Video Source
1. Locate an RCA-style composite video cable (one may be included 
with your video equipment). 
2. Connect the cable to the yellow video output connector on your 
player and the yellow 
Video connector on the projector:
3. If you want to play sound through the projector, see page 25 for 
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2 
or the Quick Setup sheet for instructions on...

18Setting Up the Projector
Connecting an S-Video Source
1. Locate an S-Video cable (one is usually provided with your video 
equipment, or you can purchase one from Epson; see page 12). 
2. Connect the cable between the S-Video connector on your player 
and the 
S-Video connector on the projector:
3. If you want to play sound through the projector, see page 25 for 
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2 
or the Quick Setup sheet for...

Setting Up the Projector19
Connecting a Component Video Source
1. Locate a component-to-VGA video cable (you can purchase one 
from Epson; see page 12).
2. Connect the RCA end of the cable to your player and the VGA 
end to the 
Computer1 port on the projector.
3. If you want to play sound through the projector, see page 25 for 
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see Chapter 2 
for instructions on turning on the projector and adjusting the...

20Setting Up the Projector
Connecting an RGB Video Source
Follow these instructions to connect the projector to a video player 
that has an RGB video output port. Depending on the type of 
connector on your player, you’ll need to use the appropriate cable:
■If your player has a VGA-style connector, see below.
■If your player has three connectors labeled R/G/B, see 
“Connecting Using a BNC-to-VGA Cable” on page 21.
Connecting Using a VGA-style Computer Cable
1. Locate the VGA computer cable provided with...