Epson P4000 Manual

Introduction11
1
1
1
1
1
1
1
1
1
1
English❏If you plan to use this product in Germany, the 
building installation must be protected by a 16 
amp circuit breaker to provide adequate 
short-circuit protection and over-current 
protection for this product.
❏Do not use a damaged or frayed AC adapter.
❏If you use an extension cord with this product, 
make sure the total amperage of all devices 
plugged into the extension cord does not exceed 
the cord’s amperage rating.
❏Never disassemble, modify, or attempt...

12Introduction
When using a memory card
❏Only memory cards designed for the product’s 
specifications can be used.
❏Do not remove a memory card or turn off the 
product while the Access lamp is flashing. See 
“LCD and control panel” on page 16 to find where 
the Access lamp is.
When using the LCD
❏The LCD panel on this product may contain a few 
small bright or dark spots. These are normal and 
do not mean that your LCD panel is damaged in 
any way.
❏If the LCD panel on this product is damaged, 
consult...

Introduction13
1
1
1
1
1
1
1
1
1
1
English❏Remove the battery from and unplug this product 
and refer servicing to qualified service personal 
under the following conditions: The power cord 
or plug is damaged; liquid has entered this 
product or its options; this product or its options 
have been dropped or the case is damaged; this 
product or its options do not operate normally or 
exhibit a distinct change in performance.
Safety information for United Kingdom users
The following safety information...

14Getting Started
Chapter 2
Getting Started
Unpacking Your P-4000
Make sure that all of the items shown below were 
included in the box with your P-4000.
* The plug type for the power cable may vary, depending on the 
local standards. P-4000Stand
Carrying caseUSB cable
Strap
Lithium-ion battery
Power cable* AC adapter
User’s Guide (this guide)
Software CD-ROM 

Getting Started15
2
2
2
2
2
2
2
2
2
2
EnglishParts
FrontBack
CF Card slot
Power switch 
with Hold 
function
Control panel LCD SD Card slot
Reset buttonCF Card slot 
eject button
Battery coverA/V Out connector
USB connectorAC adapter 
connector Headphone connector
USB connector 
rubber cover
Speaker 

16Getting Started
LCD and control panel
Print button Press this button to display 
the Print menu.
Menu button Press this button to display 
the pop up menu. For details, 
see “Using the Pop Up 
Menu” on page 49.
Charge  lamp  (Green) On when the battery is being 
charged.
OK button Print button Charge lamp
Cancel button4-way ring
Access lampMenu button
Illumination lamp
Display button
Home button
Access lamp (Orange) Flashes when accessing data 
on the HDD or a memory 
card.
4-way ring
(Up/...

Getting Started17
2
2
2
2
2
2
2
2
2
2
English
Setting Up the P-4000
After unpacking your P-4000, set it up so it is ready to 
use. This section describes how to charge the battery 
and turn the power on and off.
Charging the battery
Installing the battery
1. Slide the battery cover to the left. 
The battery cover opens.2. Insert the battery into the compartment in the 
direction of the arrow on the battery.
3. Close the battery cover and slide it to the right 
until it clicks. Home button Press this...

18Getting Started
Charging the battery
After installing the battery, charge the battery using 
the AC adapter. 
Note:
The battery status is always displayed at the top right corner 
of the LCD.
1. Make sure that the battery is installed.
c
Caution:
Do not connect the AC adapter when the battery is 
not installed. Doing so may cause P-4000 to be 
damaged.2. Connect the AC adapter to P-4000 as shown below 
and plug the other end into a power outlet.
The Charge lamp is on during charging. When the 
battery...

Getting Started19
2
2
2
2
2
2
2
2
2
2
EnglishRemoving the battery
1. Make sure that P-4000 is turned off. 
c
Caution:
❏Remove the AC adapter if it is connected to 
P-4000.
❏Never remove the battery while P-4000 is 
turned on. Doing so may cause data in the 
card or HDD to be lost or damaged.
2. Open the battery cover.
3. Push the catch down. 
The battery is pushed out.4. Pull out the battery. Then close the battery cover.
w
Warning:
Do not carry loose batteries in your pockets. 

20Getting Started
Turning the power on
Slide the power switch to   as shown below. The 
power switch will return to the original position.
The illumination lamp turns on.
When you turn on P-4000 the first time, the Language 
setting screen and Date and time settings screen are 
displayed. Follow the instructions below.1. The Language setting screen appears. Select the 
language you want to use with the 4-way ring, 
and press the OK button.
2. The Date and time settings screen appears. Press 
the Right or...