Epson Lq680 User Guide

A
Enhancing Your Printer With Options      A-5
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
R
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
6. Fully extend the paper guide extension. (If you do not plan to 
stack the printed sheets, you do not need to perform this step.)
7. If you are printing on long paper, pull out the extension flap 
located in the center of the paper guide. 

A-6      Enhancing Your Printer With Options
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
L
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
You are now ready to load paper with your cut-sheet feeder as 
described in the next section. To remove the cut-sheet feeder, turn 
off the printer and reverse the steps above.
Note:
Even if you are not using the cut-sheet feeder, you can use its paper guide 
instead of the standard paper guide. See “Loading paper manually from 
the...

A
Enhancing Your Printer With Options      A-7
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
R
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
Loading paper from the high-capacity cut-sheet feeder
Load paper in the high-capacity cut-sheet feeder (bin 1 of the 
double-bin feeder) as follows:
1. Pull both paper set levers forward until the paper guides 
retract to allow paper loading.
2. Release the paper guide lock levers by pulling them forward. 

A-8      Enhancing Your Printer With Options
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
L
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
3. Slide the right paper guide so that its edge is even with the 
guide mark on the cut-sheet feeder and push back the lever 
to lock the paper guide in place. Next, slide the left paper 
guide to roughly match the width of your paper.
4. Slide the center support midway between the paper guides.
guide mark 

A
Enhancing Your Printer With Options      A-9
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
R
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
5. Fan a stack of paper (up to 150 sheets); then tap the sides and 
bottom of the stack on a flat surface to even it up.
6. Insert the paper along the right paper guide and adjust the 
position of the left paper guide so that it matches your paper’s 
width. Make sure the position of the guide allows the paper 
to move up and down...

A-10      Enhancing Your Printer With Options
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
L
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
7. Push back the paper set levers to clamp the paper against the 
guide rollers.
8. Before printing, make sure single sheet feeding is selected. 
Also adjust the thickness setting to the paper loaded in the 
cut-sheet feeder. See “Adjusting the Paper Thickness Lever” 
on page 2-6 for details.
9. In your printer driver software, select...

A
Enhancing Your Printer With Options      A-11
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
R
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
Loading paper from the second-bin cut-sheet feeder
Follow the steps below to load paper in the second bin of the 
double-bin cut-sheet feeder.
Note:
You cannot use the second-bin cut-sheet feeder without the high-capacity 
cut-sheet feeder, although the illustrations here show only the second-
bin feeder.
1. Pull both paper set...

A-12      Enhancing Your Printer With Options
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
L
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
2. Load a fanned stack of paper (up to 50 sheets), aligning the 
right edge of the paper with the right paper guide. Be sure to 
load the paper with the printable side up. Adjust the left paper 
guide and center support to fit the paper, and then push back 
the paper set levers to lock the paper in place.
3. Before printing, make sure...

A
Enhancing Your Printer With Options      A-13
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
R
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
Switching between the tractor and the cut-sheet 
feeder
You can easily switch between continuous paper loaded from the 
tractor and single sheets loaded from the cut-sheet feeder without 
removing your continuous paper.
Switching to continuous paper
Follow the steps below to switch to continuous paper loaded from 
the tractor.
1. If...

A-14      Enhancing Your Printer With Options
R4C4590
Rev. C
A5 size OPTIONS.FM
10/30/00 Pass 1
L
Proof Sign-off:
Takahashi, Kono _______
Takahashi _______
Hoadley _______
4. Select single-sheet feeding, as described in Chapter 2, 
“Selecting a Paper Source.”
5. Pull out the paper guide extension, and pull out the extension 
flap if you are printing on long paper.
Loading paper manually from the paper guide
The cut-sheet feeder’s single-sheet loading feature allows you to 
switch to a different type or...