Home > Epson > Printer > Epson L210 Service Manual

Epson L210 Service Manual

Here you can view all the pages of manual Epson L210 Service Manual. The Epson manuals for Printer are available online for free. You can easily download all the documents as PDF.

Page 31

L200/L201/L100/L101Revision ADisassembly/AssemblyRouting FFCs/cables31
Confidential1.4 Routing FFCs/cables
Scanner Unit /CIS (L200/L201)
„When routing the Panel FFC, route it through the ribs (x7) of the Housing, and secure with double-sided tape (x3).
„When routing the Scanner FFC, secure it together with the Ferrite Core on the Housing with double-sided tape.
„When routing the Scanner Motor cable, pay attention to the following instructions.
• Secure the Ferrite core with the hooks (x2) on the rear of...

Page 32

L200/L201/L100/L101Revision ADisassembly/AssemblyRouting FFCs/cables32
Confidential
Head FFC
„When installing the Head FFC to the Carriage, route the Head FFC through the rib (x1) on the rear of the Carriage, and connect the Head FFC to the CR 
Encoder.
„When installing the Head FFC to the Main Frame, route the Head FFC in the procedure below and connect it to the Main Board.
1. Align the fold line of the Head FFC with the rib (x1) of the Holder FFC, and route the FFC through the Holder FFC as shown in...

Page 33

Confidential
CHAPTER2
ADJUSTMENT 

Page 34

L200/L201/L100/L101Revision AAdjustmentRequired Adjustments34
Confidential2.1 Required Adjustments The table below lists the required adjustments depending upon the parts being repaired or replaced. Find the part(s) you removed 
or replaced, and check which adjustment(s) must be carried out.Note: 
“O” indicates that the adjustment must be carried out. “O
*” indicates that the adjustment is recommended. “---” indicates that the adjustment is not required. If you have 
removed or replaced multiple parts,...

Page 35

L200/L201/L100/L101Revision AAdjustmentRequired Adjustments35
ConfidentialNote: In addition to the above adjustments, the following functions can be executed in the Adjustment Program. Refer to the Adjustment Program for the functions and their usage.
• Ink charge / Cleaning / Power cleaning (Each cleaning function with two options, whether counting up the waste ink counter or not.)
• Small ink counter reset
• Ink counter offset (with two options, whether counting up the waste ink counter or not.)
• Get...

Page 36

Confidential
Adjustment Details of Adjustments 36 L200/L201/L100/L101Revision A
2.2  Details of Adjustments
This section provides adjustment procedures for which explanation in details is necessary. See “ 2.1 Required 
Adjustments (p34) ” for the adjustments not explained here.
2.2.1  TOP Margin Adjustment
Three adjustment patterns are printed on the top of the paper as shown in Figure 2-1.
Figure 2-1.  Top Margin Adjustment Printout Pattern
How to Judge
Check if the top edge of the paper is within -3 to...

Page 37

Confidential
CHAPTER3
MAINTENANCE 

Page 38

Confidential
Maintenance Overview 38 L200/L201/L100/L101Revision A
3.1  Overview
This section provides information to maintain the printer in its optimum condition.
3.1.1  Cleaning
Except for the printhead, there are no other mechanism parts or units that require periodic cleaning. However, if 
need arises, clean the component observing the following instructions.
†Instructions for cleaning
„
Exterior parts such as housing
Wipe dirt off with a soft clean cloth moistened with water. For glossy or...

Page 39

L200/L201/L100/L101Revision A
ConfidentialMaintenanceLubrication Points and Instructions393.2  Lubrication Points and Instructions
Figure 3-1. Lubrication on Paper Support Assy (L200/L201)

Rail of the Paper Support 
Assy

G-74

Appropriate amount
„
Apply with brush.
„
Keep the lubrication 
within the rail. (No 
grease outside of the 
rail is allowed.)
Right side
Left side
Lubrication Point
Figure 3-2. Lubrication on Scanner Unit

Shaft on the Scanner 
Housing

G-45  (TBD)

Appropriate amount
„
Apply...

Page 40

L200/L201/L100/L101Revision A
ConfidentialMaintenanceLubrication Points and Instructions40 Figure 3-5. Lubrication on Driven Pulley HolderFigure 3-6. Lubrication on Roller Idler Pick Assy

Contacting points (x2) 
with the Driven Pulley

G-71

φ 1 mm x 1 mm

Apply with injector.
Driven Pulley Holder
Lubrication Point

Sliding surface between 
the Roller Idler Pick and 
Spring Roller Idler Pick

G-71

Appropriate amount

Apply with brush.
Lubrication Point
Figure 3-7. Lubrication on PF Roller

Ribs (x3) of...
Start reading Epson L210 Service Manual

Related Manuals for Epson L210 Service Manual

All Epson manuals