Epson Gts85 User Manual

							
Caution:
Avoid catching the cloth on the spring.
Wipe off all remaining liquid with a soft dry cloth.
Make sure that the separation pad is completely dry before using the sca\
nner.
Top
 
Cleaning the Paper Feed Roller
Open the scanner cover. See Opening the Scanner Cover for instructions.
Wipe the roller lightly with a cloth dampened with water and thoroughly \
wrung out.
Caution:
Be careful not to scratch or damage the roller.
Wipe off all remaining liquid with a soft dry cloth.
Make sure that the rollers are completely dry before using the scanner.
Top
  
						

							
 
Home > Maintenance 
Replacing the Scanner Light Source
The luminosity of the scanner light source declines over time. If the li\
ght source breaks or becomes too dim to 
operate normally, the scanner stops working and both the Power and Error\
 lights rapidly flash. When this happens, 
the light source assembly must be replaced by a professional. For detail\
s, contact Epson for support. See EPSON 
Technical Support for more information.
Caution:
Never open the scanner case. If you think repairs or adjustments are nec\
essary, contact Epson for 
support. 
						

							
 
Home > Maintenance 
Transporting the Scanner
If you need to transport your scanner some distance, carefully prepare a\
nd repack it as described below.
Turn off the scanner, then unplug the AC adapter cord.
Disconnect all the cables from the scanner.
Remove all paper from the input tray.
Close the input tray and output tray.
Attach the packing materials that came with the scanner, then repack the\
 scanner in its original box or a similar 
box that fits the scanner snugly. 
						

							
 
Home > Maintenance 
Replacing the Roller Assembly Kit
You need to replace the parts on the roller assembly kit after scanning \
every 100,000 times.Removal part Part numberNumber of scanning
Roller Assembly Kit B12B813421100,000
To replace the roller assembly kit, follow the steps below.
Turn off the scanner.
Remove all paper from the input tray.
Unplug the AC adapter from the scanner.
Pull the cover open lever and open the scanner cover.
Press the hook on the separation pad, then remove the installed separati\
on pad. 
						

							
Caution:
Do not touch the spring. Hold the separation pad holder as shown below.
Insert the bottom side of the new separation pad first, then press the h\
ook on the separation pad to attach to the 
correct position.
Press the hook on both sides of the paper feed roller cover, then open t\
he cover. 
						

							
Slide and remove the installed paper feed roller.
Caution:
Do not touch the surface of the paper feed roller. Hold the paper feed r\
oller as shown below.
Attach the new paper feed roller to the correct position. 
						

							
Caution:
Do not install the paper feed roller in reverse direction.
Close the cover of the paper feed roller, then close the scanner cover.
Turn on the scanner.
Start EPSON Scan Settings. Then, click Maintenance (Windows) or open Applications > Utilities (Mac OS X).
Click Reset on the right of the Number of Scans.
Click OK. 
						

							
 
Home > Maintenance 
Using Security Slot
A standard security lock is available with the security slot. To lock th\
e scanner, insert the lock into the back of the 
scanner and turn the key to lock the scanner. Then, secure the cable and\
 the scanner to a stationary place.
See the User’s Guide that came with the security lock for detailed in\
formation. 
						

							
 
Home > Solving Problems 
Scanner Problems
The Lights Are Flashing 
The Scanner Does Not Turn On 
You Cannot Start Epson Scan 
Pressing the Start Button Does Not Start the Correct Program 
The Lights Are Flashing
When an error occurs, the scanner Cancels operating and the Error and Po\
wer lights indicate the error type.Error light 
(Orange) Power light 
(Green)Meaning
Flashing  FlashingAn error has occurred. 
Make sure the scanner is connected to your computer 
properly.
Make sure the scanner software is fully installed. See the 
Setup Guide for instructions on installing the scanner 
software.
Paper is jammed in the scanner. Remove the jammed paper 
from the scanner. See Paper Jams in the scanner.
The scanner feeds more than one sheet of paper at a time.
Turn off the scanner and turn it on again. If the Error and 
Power lights are still flashing, the scanner may be 
malfunctioning, or the scanner light source may need to be 
replaced. See EPSON Technical Support for details.
On OffScanner cover is open.
Top
 
The Scanner Does Not Turn On
Make sure your scanner’s AC adapter is securely connected to the scan\
ner and a working electrical outlet.
Make sure the electrical outlet works. If necessary, test it by plugging\
 in another electrical device and turning it 
on. Top
 
You Cannot Start Epson Scan
Make sure the scanner is turned on.
Turn off the scanner and computer, then check the interface cable connec\
tion between them to make sure it is 
secure. 
						

							
Use the USB cable that came with your scanner or that is indicated in USB Interface.
Connect the scanner directly to the computer’s USB port or through on\
e USB hub only. The scanner may not 
work properly when connected to the computer through more than one USB h\
ub.
Make sure your computer supports USB.
If you are using any TWAIN-compliant program, make sure that the correct\
 scanner is selected as the Scanner 
or Source setting.
If you upgraded your computer’s operating system, you need to reinsta\
ll Epson Scan. Uninstall Epson Scan as 
described in Uninstalling Your Scanning Software, then reinstall it as described in the Setup Guide.
For Windows only: 
Make sure your scanner’s name appears under Imaging device without a \
(?) or an exclamation (!) mark in the Device 
Manager window. If the scanner’s name appears with one of these marks\
 or as an Unknown device, uninstall Epson Scan 
as described in Uninstalling Your Scanning Software, then reinstall it as described in the Setup Guide.
Top
 
Pressing the Start Button Does Not Start the Correct Program
Make sure Epson Scan and Epson Event Manager (Mac OS X only) is instal\
led correctly. 
Check if you have assigned a program to the scanner button. See Assigning a Program to LCD Screen Menu List 
for details.
Mac OS X: Make sure you are logged on as the user who installed the scanner softw\
are. Other users must first 
start Epson Scanner Monitor in the Applications folder and then press th\
e 
 Start button to scan.Top