Epson EPL N3000T User Manual

							358Functions of the Control Panel
Confidential Job Menu
This menu allows you to print or delete print jobs stored in the 
printer’s Hard Disk Drive using the Confidential Job feature of 
the printer driver’s Reserve Job function. You need to enter the 
correct password to access this data. For instructions on using this 
menu, see “Using the Confidential Job Menu” on page 342.
Reset Menu
This menu allows you to cancel printing and reset the printer 
settings.
Clear Warning
Clears the last warning message that appear on the LCD panel.
Clear All Warnings
Clears all warning messages that appeared on the LCD panel and 
are still stored in the printer’s memory.
Reset
Stops printing and clears the current job received from the active 
interface. You may want to reset the printer when there is a 
problem with the print job itself and the printer cannot print 
successfully.
Reset All
Stops printing, clears the printer memory, and restores the printer 
settings to their default values. The print jobs received from all 
interfaces are erased.
Note:
Performing Reset All clears print jobs received from all interfaces. Be 
careful not to interrupt someone else’s job.
 
						

							Functions of the Control Panel359
B
B
B
B
B
B
B
B
B
B
B
B
SelecType Init
Restores the control panel menu settings to their default values. 
Yellow Regist, Magenta Regist, and Cyan Regist settings are not 
reset.
Reset Fuser Counter
Reset the fuser unit life when you replace the fuser unit.
Parallel Menu
These settings control communication between the printer and 
the computer when using the parallel interface.
Parallel I/F
Allows you to activate or deactivate the parallel interface.
Speed
Specifies the pulse width of the ACKNLG signal when receiving 
data in the Compatibility mode or Nibble mode. When Fast is 
selected, the pulse width is about 1 µs. When Normal is selected, 
the pulse width is about 10 µs.
Bi-D
Allows you to specify the bidirectional communication mode. 
When you select Off, bidirectional communication is disabled.
Item Settings (default in bold)
Parallel I/FOn, Off
SpeedFast, Normal
Bi-D Nibble, ECP, Off
Buffer SizeNormal, Maximum, Minimum
 
						

							360Functions of the Control Panel
Buffer Size
Determines the amount of memory to be used for receiving data 
and printing data. If Maximum is selected, more memory is 
allocated for receiving data. If Minimum is selected, more memory 
is allocated for printing data.
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in “Reset Menu” on page 358. 
❏Resetting the printer erases all print jobs. Make sure the Ready light 
is not flashing when you reset the printer.
USB Menu
These settings control communication between the printer and 
the computer when using the USB interface.
USB I/F
Allows you to activate or deactivate the USB interface.
Buffer Size
Determines the amount of memory to be used for receiving data 
and printing data. If Maximum is selected, more memory is 
allocated for receiving data. If set to Minimum is selected, more 
memory is allocated for printing data.
Item  Settings (default in bold)
USB I/FOn, Off
Buffer SizeNormal, Maximum, Minimum
 
						

							Functions of the Control Panel361
B
B
B
B
B
B
B
B
B
B
B
B
Note:
❏To activate Buffer Size settings, you must turn off the printer for 
more than five seconds then turn it back on. Or, you can perform a 
Reset All operation, as explained in “Reset Menu” on page 358. 
❏Resetting the printer erases all print jobs. Make sure the Ready light 
is not flashing when you reset the printer.
Network Menu
See the Network Guide for each setting.
AUX Menu
See the Network Guide for each setting.
 
						

							362Functions of the Control Panel
LJ4 Menu
These settings control the fonts and symbol sets when in the LJ4 
mode.
Item Settings (default in bold)
Font SourceResident, Download*
Font Number0 to 65535 (depending on your settings)
Pitch** 0.44 ... 10.00 ... 99.99 cpi in 0.01-cpi increments
Height** 4.00 ... 12.00 ... 999.75 pt in 0.25-pt increments
SymSetIBM-US, Roman-8, Roman-9, ECM94-1, 8859-2 
ISO,8859-9 ISO, 8859-10ISO, 8859-15ISO, 
PcBlt775, IBM-DN, PcMultiling, PcE.Europe, 
PcTk437, PcEur858, Pc1004, WiAnsi, WiE.Europe, 
WiTurkish, WiBALT, DeskTop, PsText, VeInternati, 
VeUS, MsPublishin, Math-8, PsMath, VeMath, 
PiFont, Legal, UK, ANSI ASCII, Swedis2, Italian, 
Spanish, German, Norweg1, French2, Windows, 
McText, PcIcelandic, PcLt774, PcTurk1, 
PcPortugues, PcEt850, PcTurk2, PcCanFrench, 
PcSl437, PcNordic, 8859-3 ISO, 8859-4 ISO, 
WiBaltic, WiEstonian, WiLatvian, Mazowia, 
CodeMJK, BpBRASCII, BpAbicomp, PcGk437, 
PcGk851, PcGk869, 8859-7 ISO, WiGreek, 
Europe3, PcCy855, PcCy866, PcLt866, PcUkr866, 
PcLit771, 8859-5 ISO, WiCyrillic, Bulgarian, 
Hebrew7, 8859-8 ISO, Hebrew8, PcHe862, 
Arabic8, PcAr864, 8859-6 ISO, OCR A, OCR B, 
Pc866Cyr, Pc866Ukr, WinCyr, ISOCyr, Pc8Grk, 
Pc851Grk, WinGrk, ISOGrk, Greek8, Pc862Heb, 
Pc864Ara, HPWARA
Form 5 ... 64 ... 128 lines
Source SymSet 0 ... 277 ... 3199
Dest SymSet 0 ... 277 ... 3199
CR FunctionCR, CR + LF
LF FunctionLF, CR + LF
Tray Assign 4, 4K, 5S
 
						

							Functions of the Control Panel363
B
B
B
B
B
B
B
B
B
B
B
B
* Available only when the download fonts are installed.
Note:
If you normally use the HP LaserJet 4 printer driver when printing, you 
should change settings using this driver whenever you can. Printer 
driver settings always override the LJ4 Menu options.
FontSource
Sets the default font source.
Font Number
Sets the default font number for the default font source. The 
available number depends on the settings you made.
Pitch
Specifies the default font pitch if the font is scalable and of 
fixed-pitch. You can select from 0.44 to 99.99 cpi (characters per 
inch), in 0.01-cpi increments. This item may not appear 
depending on the Font Source or Font Number settings.
Height
Specifies the default font height if the font is scalable and 
proportional. You can select from 4.00 to 999.75 points, in 
0.25-point increments. This item may not appear depending on 
the Font Source or Font Number settings.
SymSet
Selects the default symbol set. If the font you selected in Font 
Source and Font Number is not available in the new SymSet 
setting, the Font Source and the Font Number settings are 
automatically replaced with the default value, IBM-US.
 
						

							364Functions of the Control Panel
Form
Selects the number of lines for the selected paper size and 
orientation. This also causes a line spacing (VMI) change, and the 
new VMI value is stored in the printer. This means that later 
changes in the Page Size or Orientation settings cause changes in 
the Form value, based on the stored VMI.
Source SymSet, Dest SymSet
Available only in certain locations where printers are sold with a 
special ROM module installed to handle specific languages.
CR Function, LF Function
These functions are included for users of particular operating 
systems, such as UNIX.
Tray Assign
Changes the assignment for the paper source select command. 
When 4 is selected, the commands are set as compatible with the 
HP LaserJet 4. When 4K is selected, the commands are set as 
compatible with the HP LaserJet 4000, 5000, and 8000. When 5S 
is selected, the commands are set as compatible with the HP 
LaserJet 5Si.
 
						

							Functions of the Control Panel365
B
B
B
B
B
B
B
B
B
B
B
B
GL2 Menu
This menu lets you set the printer to emulate a plotter, allowing 
you to use software which requires a plotter for output. The 
LJ4GL2 mode is similar to the GL/2 mode supported in the HP 
LaserJet 4 mode. The GLlike mode emulates some of the HP-GL 
plotter commands and includes all the commands found in HP’s 
GL/2 mode, as well as two additional commands.
* Available only when GLlike is selected as the GL Mode.
Before you start printing in the GL/2 mode
You may need to change the following print options in your 
application, depending on your output needs. Check these 
settings to make sure they match the data you are trying to print.
Item Settings (default in bold)
GL ModeLJ4GL2, GLlike
ScaleOff, A0, A1, A2, A3
OriginCorner, Center
PenPen0, Pen1, Pen2*, Pen3*, Pen4*, Pen5*, 
Pen6*
EndButt, Square, Triangular, Round
JoinMitered, Miteredbeveled, Triangular, Round, 
Beveled, None
Pen 0 through 6 0.05 ... 0.35 ... 5.00 mm in 0.05-mm increments
Print Options Settings
Paper size Printer’s paper size setting
Driver (plotter selection) HP-GL/2 or HP-GL
Pen configuration Pen thickness
Plot origin Center or Corner
 
						

							366Functions of the Control Panel If you need to configure the printer settings, first switch to the 
GL/2 emulation mode, then change the settings using the printer 
driver, or the control panel menus.
Note:
Settings or data saved in the printer’s RAM (such as downloaded fonts) 
may be erased when you change the emulation mode.
GL Mode
Specifies whether the printer uses a direct emulation of the GL/2 
plotter language, or the HP LaserJet 4 emulation of GL/2.
Scale
Specifies whether the output from the software is scaled. The scale 
factor is based on the output paper size of the application.
Origin
Specifies whether the logical origin of the “plotter” is the corner 
or the center of the paper.
Pen
Allows you to choose a pen which you can then set the thickness 
for in the Pen 0 through 6 item. The LJ4GL2 mode supports two 
pens (0 and 1), while the GLlike mode supports seven pens (0 
through 6).
End
Specifies the way in which lines end.
OrientationGLlike offers landscape only
LJ4GL2 offers landscape and portrait Print Options Settings
 
						

							Functions of the Control Panel367
B
B
B
B
B
B
B
B
B
B
B
B
Join
Specifies the way in which lines are joined.
Pens 0 through 6
Allows you to set the thickness of the pens used to make the 
printout. Pen 0 and Pen 1 are available in the LJ4GL2 mode, and 
Pen 0 through Pen 6 are available in the GLlike mode.
PS3 Menu
These settings are available in the PS3 mode.
Error Sheet
When you select On, the printer prints out an error sheet.
Image Protect
Allows you to specify whether to employ lossy compression. 
Lossy compression refers to a data compression technique in 
which some amount of data is lost.
Item Settings (default in bold)
Error SheetOff, On
Image ProtectOff, On