Epson EPL N3000DTS User Manual

188Setting Up Your Printer on a Network❏The name of the shared printer may be changed by the computer 
or server that is connected to the shared printer. To make sure 
of the name of the shared printer, ask the administrator of the 
network.
❏If the printer driver is installed in the client beforehand, you 
need to select the new printer driver or the current printer 
driver. When the prompt to select the printer driver appears, 
select the printer driver according to the message.
❏If the additional...

Setting Up Your Printer on a Network189
6
6
6
6
6
6
6
6
6
6
6
6
❏On the Device Settings sheet of the printer’s Properties dialog 
box, make sure that SEND CTRL-D Before Each Job and 
SEND CTRL-D After Each Job are set to No.
❏TBCP (Tagged binary communications protocol) cannot be 
used as the Output Protocol setting.
Installing the Printer Driver from the CD-ROM
This section describes how to install the printer driver in the 
clients when setting the network system as follows:
❏Additional drivers are not...

190Setting Up Your Printer on a Network 1. Access the shared printer and a prompt may appear. Click 
OK, and then follow the on-screen instructions to install the 
printer driver from the CD-ROM.
2. Insert the CD-ROM, then type the appropriate drive and 
folder names in which the printer driver for clients is located, 
then click OK.
If you are installing drivers in Windows XP or 2000, “Digital 
Signature is not found.” may appear. Click Yes (Windows 
2000) or Continue Anyway (Windows XP) and continue...

Installing Options191
7
7
7
7
7
7
7
7
7
7
7
7
Chapter 7
Installing Options
550-Sheet Paper Cassette Unit A4
The following table summarizes the paper types and sizes that 
you can use with the optional Universal Cassette Unit.
Note:
Load paper with the printable surface facing up.
Paper Type Paper Size Capacity
Plain paper A4, A5, B5
Letter (LT), Half-Letter 
(HLT), Legal (LGL),
Government Letter 
(GLT), Government 
Legal (GLG), Executive 
(EXE), F4Up to 550 sheets (64 
g/m²)
Up to 550 sheets (75 
g/m²)...

192Installing Options
Handling precautions
Always pay attention to the following handling precautions 
before installing the cassette unit.
The printer weighs about 20.9 kg (46.1 lb). One person should 
never attempt to lift or carry it alone. Two people should carry 
the printer, lifting it from the positions shown below.
w
Warning:
If you lift the printer incorrectly, you could drop it and cause 
injury.
Note:
The rear side of the printer is extremely heavy. Take care when you lift 
the printer.
Follow...

Installing Options193
7
7
7
7
7
7
7
7
7
7
7
7
1. Turn the printer off and unplug the power cord and interface 
cable.
c
Caution:
Make sure to unplug the power cord from the printer to 
prevent getting an electrical shock. 
2. Place the printer onto the 550-Sheet Universal Paper Cassette 
Unit. Align each of the printer’s corners with those of the unit, 
then lower the printer until it rests securely on the unit.
Note:
❏The printer should be carried by at least two people, holding the 
printer with their...

194Installing Options❏When you install two optional paper cassette units, put one unit 
upon the other unit in order, then put the printer on top of them.
3. Pull out the MP tray and lower paper cassette from the printer, 
and then pull out the optional lower paper cassette from the 
unit. Then, secure the printer to the unit with the four fittings 
that are provided. Install two of the four fittings on both sides 
of the inside of the printer.
 

Installing Options195
7
7
7
7
7
7
7
7
7
7
7
7
4. Remove the protective materials from the cassette and load 
the paper.
5. Reconnect the interface cable and power cord, then turn the 
printer on.
6. To confirm that the option is installed correctly, print a Status 
Sheet. See “Printing a Status Sheet” on page 260.
Note:
If you are using Windows, and EPSON Status Monitor 3 is not 
installed, you have to make settings manually in the printer driver. Click 
the Update the Printer Option Information Manually...

196Installing Options 1. Turn the printer off and unplug the power cord and interface 
cable.
c
Caution:
Make sure to unplug the power cord from the printer to 
prevent getting an electrical shock. 
2. Remove the duplex unit connector cover. Then, pinch the two 
hooks on the option cover to remove it from cover B.
 

Installing Options197
7
7
7
7
7
7
7
7
7
7
7
7
Note:
Keep the duplex unit connector cover in a safe place prevent to lose.
3. Install the Duplex Unit as shown below. Make sure that the 
unit hooks onto the printer’s tabs and the duplex connector 
goes into the slot.
4. Secure the unit with the two screws provided.
5. Reconnect the interface cable and power cord, then turn the 
printer on.