Epson EPL N2550DTT User Manual

Installing Options211
8
8
8
8
8
8
8
8
8
8
8
8
Removing an interface card
c
Caution:
Before you remove an interface card, be sure to discharge any 
static electricity by touching a grounded piece of metal. 
Otherwise, you may damage static-sensitive components.
Perform the installation procedure in reverse.
 

212Replacing Consumable Products
Chapter 9 
Replacing Consumable Products
Replacement Messages
When you see the following messages on the LCD panel or the 
window of EPSON Status Monitor, replace the appropriate 
consumable products. You can continue to print for a short time 
after a message appears, but EPSON recommends early 
replacement to maintain print quality and extend the life of your 
printer.
Note:
To clear these messages, select Clear All Warnings in Reset Menu.
When the Toner out setting in...

Replacing Consumable Products213
9
9
9
9
9
9
9
9
9
9
9
9
Imaging Cartridge
Handling precautions
Always observe the following handling precautions when 
replacing imaging cartridges.
❏When handling imaging cartridges, always place them on a 
clean smooth surface.
❏Do not install used imaging cartridges into the printer.
❏If you have moved an imaging cartridge from a cool to a warm 
environment, wait for at least one hour before installing it to 
prevent damage from condensation.
❏Do not open the drum’s...

214Replacing Consumable Products
w
Warning:
❏Do not touch the toner. Keep the toner away from your eyes. 
If toner gets on your skin or clothes, wash it off with soap and 
water immediately.
❏Keep the consumable products out of the reach of children.
❏Do not dispose of the consumable products in fire, as they 
may explode and cause injury. Dispose of them according to 
local regulations.
Replacing an imaging cartridge
Follow these steps to replace an imaging cartridge.
1. Open Cover A slowly.
 

Replacing Consumable Products215
9
9
9
9
9
9
9
9
9
9
9
9
2. Hold the handle of the imaging cartridge and pull out from 
the printer.
3. Take the new imaging cartridge out of its package and gently 
shake the imaging cartridge as shown below.
 

216Replacing Consumable Products 4. Put the new imaging cartridge on the flat surface and pull out 
the protective cartridge seal as shown below.
5. Insert the new imaging cartridge all the way until it stops.
Note:
Insert the cartridge with the arrow mark on the top of the imaging 
cartridge facing toward Cover A.
 

Replacing Consumable Products217
9
9
9
9
9
9
9
9
9
9
9
9
6. Close Cover A until it clicks shut.
Note for windows users:
If EPSON Status Monitor is installed, the information about the 
amount of toner remaining on the Basic Setting screen may not be 
updated. In that case, press the Get Information Now button on 
the Consumable Info Settings dialog box to update the information. 
You can open the Consumable Info Settings dialog box by 
clicking the Consumable Info Settings button on the Optional...

218Replacing Consumable Products
w
Warning:
❏The fuser unit can be very hot if the printer has been in use. 
Turn the printer off and wait for 40 minutes until the 
temperature has subsided before replacing the fuser unit.
❏Do not dispose of the used consumable products in fire, as it 
may explode and cause injury. Dispose of it according to local 
regulations.
❏Keep the consumable products out of the reach of children.
Replacing the fuser unit
Follow the steps below to replace the fuser unit.
1. Turn...

Replacing Consumable Products219
9
9
9
9
9
9
9
9
9
9
9
9
2. Open cover B.
3. Pull down the two levers at either side of the fuser unit.
 

220Replacing Consumable Products 4. Remove the fuser unit slowly.
5. Slowly insert the new fuser unit.