Epson C1600 Manual

❏Position the removed photoconductor unit horizontally as shown in the illustration below.
Be sure to keep the photoconductor unit horizontal and place it where it will not become dirty.
Do not leave the photoconductor unit removed for more than 15 minutes, and do not place the
removed photoconductor unit in a location where it would be exposed to direct light (such as
sunlight).
7. Clean the print head window by wiping it with a soft, dry cloth.
c
Caution:
The area around the fuser unit is extremely...

Note:
Decreased print quality may result if the surface of the transfer roller is touched.
Be careful not to touch the surface of the transfer roller.
8. Slowly insert the photoconductor unit vertically, and then push it slightly down toward you to
finish reinstalling the photoconductor unit.
AcuLaser C1600     User’s Guide
Maintenance     62 

9. Close the top cover.
10. Press the Clear key.
Note:
The blinking of all indicators stop, and the magenta toner indicator lights up.
The toner cartridges rotate within the printer.
11. After the toner cartridges have finished rotating, open the front cover.
AcuLaser C1600     User’s Guide
Maintenance     63 

12. Align the shaft on each end of the toner cartridge with its holders, and then insert the cartridge.
Note:
Do not touch the contact indicated in the illustration.
AcuLaser C1600     User’s Guide
Maintenance     64 

13. Press in the magenta toner cartridge until it locks into place.
14. Close the front cover.
AcuLaser C1600     User’s Guide
Maintenance     65 

Long-term storage of the printer
If the printer will not be used for a month or more, install the protective materials onto the fuser unit.
AcuLaser C1600     User’s Guide
Maintenance     66 

Chapter 7
Troubleshooting
Introduction
This chapter provides information to aid you in resolving printer problems you may encounter, or at
least guide you to the proper sources for help.
Preventing Media Misfeeds 
Make sure that...
Media matches the printer specifications.
Media is flat, especially on the leading edge.
The printer is on a hard, flat, level surface.
You store media in a dry location away from moisture and humidity.
Y o u  a l w a y s  a d j u s t  t h e  m e d i a  g u i d e s  i n  T r a...

Indicator Messages
The indicators on the control panel provide information about your printer and help you locate each
problem.
Status Messages (Ready Indicator, Error Indicator)
Status messages indicate the current condition of the printer. 
The printer status also can be checked on the Remote Panel Program. 
(Refer to “Working with the Remote Panel Program” on page 20.)
Ready
indicator
(green)Error
indicator
(orange)Display of
Remote Panel
ProgramCondition Action
Off Off - Power off None
Slow blinking...

Ready
indicator
(green)Error
indicator
(orange)Toner
indicator
(orange)Display of
Remote
Panel
ProgramCondition Action
On Off On TONER OUT
X (YMCK)Toner out
Note: 
This message appears
when the Toner Out
Stop in the Remote
Panel Program is set to
Off.Replace the toner
cartridge.
Note: 
Printing can continue,
however, the printing
results are not
guaranteed.
If printing is continued,
the Error indicator
(orange) lights up and
printing stops.
On Slow
blinkingRapid
BlinkingNON
GENUINE
TONER X
(YMCK)The...

Ready
indicator
(green)Error
indicator
(orange)Toner
indicator
(orange)Display of
Remote
Panel
ProgramCondition Action
Off Slow
blinking* P/U END Photoconductor unit
endReplace the
photoconductor unit.
Note: 
Printing can continue,
however, the printing
results are not
guaranteed.
If printing is continued,
the Error indicator
(orange) lights up and
printing stops.
* Differs depending on the toner status.
Error Messages
These messages indicate errors which you must correct before a print job can continue...