Epson C 2900 Manual

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 157 Confidential 
 
RRP6.2 STOPPER PIVOT (PL6.1.3), PIVOT TRANS L (PL6.1. 4), GEAR T4 (PL6.1.5), 
SHAFT ASSY  PIVOT  (PL6.1.6)  , COVER HARNESS(PL6.1.8)  
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
3) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 158 Confidential 
 
11) Rotate the STOPPER PIVOT 
(PL6.1.3), mate the tabs of the STOPPER 
PIVOT with the notches of the DRIVE 
ASSY MAIN (PL7.1.2). 
12) Remove the STOPPER PIVOT from 
the printer. 
Note: When carrying out the work described next procedure, take care not to drop the GEAR T4. 
13) Pull out the PIVOT TRANS L 
(PL6.1.4), remove the GEAR T4 (PL6.1.5) 
from the printer.  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 159 Confidential 
 
14) Remove the one screw (silver, tap, 
8mm) that fixes the SHAFT ASSY PIVOT 
(PL6.1.6) to the printer. 
Note: When carrying out the work described next procedure, keep the TRANSFER ASSY slightly 
lifted for ease of work. 
15) Pull out the SHAFT ASSY PIVOT from 
the printer. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 160 Confidential 
 
 [Replacement] 
1) Mate the hole of the TRANSFER ASSY 
with the hole of the printer frame, attach 
the SHAFT ASSY PIVOT. 
2) Secure the SHAFT ASSY PIVOT to the 
printer with the one screw (silver, tap, 
8mm). 
Note: When carrying out the work 
described next procedure, make sure 
that the position of the GEAR T4 is 
correctly. 
Note: When carrying out the work described next procedure, keep the TRANSFER...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 161 Confidential 
 
3) Attach the GEAR T4 to the printer, align 
the holes of the GEAR T4, the printer 
frame, and the TRANSFER ASSY, and 
then insert the PIVOT TRANS L. 
Note: When carrying out the work 
described next procedure, ensure that 
the flat face of the PIVOT TRANS L is 
oriented to the direction shown in the 
right. 
4) Mate the tab of the STOPPER PIVOT 
with the notch of the DRIVE ASSY MAIN, 
attach the...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 162 Confidential 
 
5) Rotate the STOPPER PIVOT to the left, 
secure the STOPPER PIVOT to the DRIVE 
ASSY MAIN frame. 
6) Mate the notch of the CLUTCH ASSY 
DRV with the rib of the DRIVE ASSY PH, 
secure the CLUTCH ASSY DRV to the 
ROLL ASSY REGI with the E-ring by using 
a pliers. 
7) Route the harness of the CLUTCH 
ASSY DRV through the hook of the DRIVE 
ASSY PH. 
  

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 163 Confidential 
 
RRP6.3 TRANSFER ASSY (PL6.1.7)   
[Removal] 
1) Remove the CASSETTE ASSY 250. (RRP2.1) 
2) Open the COVER ASSY FRONT MG (PL1.2.1). 
Note: Cover the drum of the DRUM CARTRIDGE to avoid exposure to light.  
3) Remove the DRUM CARTRIDGE. (RRP4.6)  
Note: The FUSING part is very hot. Take added care not to get burned when performing the 
service operation. 
4) Remove the FUSER UNIT. (RRP6.1) 
5) Remove the...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 164 Confidential 
 
11) Release the harness from the pegs of 
he TRANSFER ASSY, disengage the 
connector (P/J281) of the TRANSFER 
ASSY. 
12) Release the harness coming from 
printer from hook of the TRANSFER 
ASSY. 
13) Tilt the TRANSFER ASSY slowly. 
14) Remove the STOPPER PIVOT (PL6.1.3), PIVO T TRANS L (PL6.1.4), GEAR T4 (PL6.1.5), and 
SHAFT ASSY PIVOT (PL6.1.6). (RRP6.2) 
15) Remove the TRANSFER ASSY from 
the...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 165 Confidential 
 
 [Replacement] 
1) Attach the TRANSFER ASSY to the 
printer. 
2) Attach the SHAFT ASSY PIVOT (PL6.1.6),GEAR  T4 (PL6.1.5), PIVOT TRANS L(PL6.1.4) and 
STOPPER PIVOT (PL6.1.3). (RRP6.2). 
3) Close the TRANSFER ASSY. 
Note: When carrying out the work described next procedure, take care not to scratch the belt 
surface of the TRANSFER ASSY. 
4) Route the harness of the printer through 
the hooks of the...

Chapter 3 Removal and Replacement Procedures Revision B 
Epson AcuLaser C2900N 3 - 166 Confidential 
 
5) Engage the connector (P/J281) of the 
TRANSFER ASSY, secure the relay 
connector with the pegs of the TRANSFER 
ASSY. 
6) Attach the COVER HARNESS to the 
TRANSFER ASSY.