Epson AcuLaser C4200DTN User Manual

Paper Handling51
3
3
3
3
3
3
3
3
3
3
3
3
5. Insert the stack into the cassette, lining it up with both the front and left sides of the cassette, with the printable surface 
up.
6. Slide the paper guides to fit the paper you are loading.
 

52Paper Handling
7. Reinsert the cassette into the unit.
Note:
❏After loading paper, set the  LC 1 Size through LC 4 Size  
and  LC 1 Type  through LC 4 Type  settings on the control 
panel to match the loaded paper size and type.
❏ If you have installed and loaded paper into the optional paper 
cassette unit, set the setting for the cassette that you are using.
Output tray
New :t he
 information
 about t
he o
ther
 o
utput
 tray, quote
 from t
he
 similar p
roduct/
 Face d
ownThe output tray is located...

Paper Handling53
3
3
3
3
3
3
3
3
3
3
3
3
Note:
This tray can hold up to 250 sheets. The printer automatically stops 
printing if the total thickness  of the printout reaches 36 mm.
Printing on Special Media
You can print on special media which include Epson paper such 
as the following. 
Note:
Since the quality of any particular brand or type of media may be changed 
by the manufacturer at any time, Epson cannot guarantee the quality of 
any type of media. Always test samp les of media stock before...

54Paper Handling
❏
You can also make these settings on the  Tray Menu in the 
control panel. See Tray Menu on page 219.
EPSON Color Laser Transparencies
Ne w
 :Color o
nly/with
 control
 panel/ i
ncluding
 t
he
 information
 about d
uplex
 printing/quote
 the i
nformation f
rom s
imilar
 product
 (how t
o
 l
oad t
ransparencies)Epson recommends the use of EPSON Color Laser 
Transparencies.
Note:
Duplex printing is not available for transparencies.
Transparencies can be loaded into the MP tray only. When...

Paper Handling55
3
3
3
3
3
3
3
3
3
3
3
3
❏When the Paper Type setting in the printer driver is set to 
Transparency , do not load any other type of paper except 
transparencies.
Please note the following when handling this media:
❏ Hold each sheet by its edges, as oil from your fingers may 
transfer to the surface and damage the printable surface of the 
sheet. The Epson logo appears on the printable side.
❏ When loading transparencies in the MP tray, insert the short 
edge first as shown below.
❏ If...

56Paper Handling
Envelopes
New
 :with
 control
 panel/
 including t
he
 information
 about
 duplex
 printingThe print quality of envelopes may be irregular because different 
parts of an envelope have different thicknesses. Print one or two 
envelopes to check the print quality.
c
Caution:
Do not use window envelopes. The plastic on most window 
envelopes will melt when it comes into contact with the fuser.
Note:
❏ Depending on the quality of envelopes, the printing environment, 
or the printing...

Paper Handling57
3
3
3
3
3
3
3
3
3
3
3
3
❏Load envelopes with the short edge first as shown below.
❏ When printing on DL size envelopes, load them with the long 
edge first.
❏ Do not use an envelope that has glue or tape on it.
c
Caution:
Make sure that the minimum size of envelopes meets the 
following size requirements:
1. Minimum length of a long edge: 176 mm
2. Minimum length of a short edge: 110 mm
Labels
New :with c ontrol
 panel/ i
ncluding
 the
 information a
bout
 d
uplex
 printing
1
2
 

58Paper Handling
You can load up to 15 mm thickness of labels into the MP tray at 
a time. However, you may need to feed some labels one sheet at 
a time, or load them manually.
Note:
❏
Duplex printing is not available for labels.
❏ Depending on the quality of labels, the printing environment, or the 
printing procedure, labels might be wrinkled. Make a trial print run 
before you print on a lot of labels.
When loading labels, you should make paper settings as shown 
below:
❏ Make settings on the Basic...

Paper Handling59
3
3
3
3
3
3
3
3
3
3
3
3
Thick paper and extra thick paper
New :with c
ontrol
 panel/ i
ncluding
 the i
nformation a
bout
 duplex
 printing/If
 unnecessary, delete
 note t
extYou can load thick paper (106 to 163 g/m²) or extra thick paper 
(164 to 216 g/m²) into the MP tray.
When loading thick or extra thick paper, you should make paper 
settings as shown below:
❏ Make settings on the Basic Settings in the printer driver.
Note:
When using extra thick paper, you cannot do duplex printing...

60Paper HandlingNote:
❏
For Windows, access the printer driver, then select 
User-Defined Size  from the Paper Size list on the  Basic 
Settings  tab. In the User Defined Paper Size dialog box, adjust 
the Paper Width, Paper Length, and Unit settings to match 
your custom paper. Then click  OK and your custom paper size 
will be saved.
❏ For Macintosh, access the printer driver, click  Custom Size in 
the Paper Setting dialog box. Then click  New, adjust the Paper 
Width, Paper Length, and Margin...