Epson AcuLaser C2800DTN User Manual

AcuLaser C2800 Series Users Guide
Using the Control Panel171
Password Config Menu
This menu allows you to restrict operation of the printer.
*The default password is Null. You can enter up to 20 characters for the password.
Password Config
Changes the password. Enter the old password first and then enter the new password twice.
To enter the password, press the dDown or uUp button to select the character and press the 
Enter button to determine the character. After all characters are determined, select...

AcuLaser C2800 Series Users Guide
Using the Control Panel172
Cancel All Print Job
The printer is canceling all print jobs in the printer memory, including jobs the printer is currently 
receiving or printing. This message appears when the +Cancel Job button has been pressed 
down for more than 2 seconds.
Cancel Print Job
The printer is canceling the current print job. This message appears when the +Cancel Job button 
has been pressed and released within 2 seconds.
Cancel Print Job (by host)
The print job...

AcuLaser C2800 Series Users Guide
Using the Control Panel173
To clear the error, see “Transparencies are output blank from the MP tray” on page 240.
Check Paper Size
The paper size setting is different from the size of paper loaded in the printer. Check to see if the 
correct size of paper is loaded in the specified paper source.
To clear this error, select Clear Warning from the control panel’s Reset Menu. See “How to access 
the control panel menus” on page 146 for instructions.
Check Paper Type
The...

AcuLaser C2800 Series Users Guide
Using the Control Panel174
Duplex Mem Overflow
There is not enough memory for duplex printing. The printer prints only on the front and ejects the 
paper. To clear this error, follow the instructions below.
If Off is selected as the Auto Cont setting on the control panel’s Setup Menu, press the NStart/Stop 
button to print on the back of the next sheet, or press the +Cancel Job button to cancel the print 
job.
If On is selected as the Auto Cont setting on the control...

AcuLaser C2800 Series Users Guide
Using the Control Panel175
Install Fuser
There is no fuser unit installed or the fuser unit is not installed properly. Turn off the printer, then 
install the fuser unit if it is not installed. 
If a fuser unit is already installed, turn the printer off and wait until it has cooled off (30 minutes). 
Then open the front cover. Remove the fuser unit, reinstall it properly, and then close the front 
cover. The error clears automatically if the fuser unit is properly...

AcuLaser C2800 Series Users Guide
Using the Control Panel176
Manual Duplex
One side for the manual duplex printing is finished. To start printing on the other side, set the 
paper and press the NStart/Stop button. See “Printing with the Duplex Unit (models with Duplex 
Unit only)” on page 55 for windows, or “Printing with the Duplex Unit (models with Duplex Unit 
only)” on page 118 for Macintosh.
Manual Feed ssss
The manual feed mode is specified for the current print job. Make sure the paper size...

AcuLaser C2800 Series Users Guide
Using the Control Panel177
NonGenuine Toner uuuu
The installed imaging cartridge is not a genuine Epson imaging cartridge. The printout and 
remaining service lives of the imaging cartridges displayed on the control panel may be different 
from those when using genuine EPSON imaging cartridges. Epson shall not be liable for any 
damages or problems arising from the use of consumable products not manufactured or approved 
by Epson. Installing a genuine imaging cartridge...

AcuLaser C2800 Series Users Guide
Using the Control Panel178
Paper Set tttt sssss
The paper loaded in the specified paper source (tttt) does not match the required paper size 
(sssss). Replace the loaded paper with the correct size paper and press the NStart/Stop button to 
resume printing, or press the +Cancel Job button to cancel the print job.
If you press the NStart/Stop button without replacing the paper, the printer will print on the 
loaded paper even though it does not match the required size....

AcuLaser C2800 Series Users Guide
Using the Control Panel179
Replace Toner uuuu
The indicated imaging cartridges have reached the end of its service life and need to be replaced. 
(The letters C, M, Y, or K appear in place of uuuu and indicate the colors Cyan, Magenta, Yellow, 
and Black respectively.)
When the error light turns on, you cannot continue printing. Replace the imaging cartridge with a 
new one. See “Imaging Cartridge” on page 202 for instructions.
When the error light is blinking, you can...

AcuLaser C2800 Series Users Guide
Using the Control Panel180
Reset to Save
A control panel menu setting was changed while the printer was printing. Press the NStart/Stop 
button to clear this message. The setting will become effective after printing has finished.
Alternatively you can clear this message by performing Reset or Reset All on the control panel. 
However, the print data will be deleted.
ROM CHECK
The printer is checking the ROM.
Self Test
The printer is currently performing a self test and...