Epson AcuLaser C1100D User Manual

							Troubleshooting201
8
8
8
8
8
8
8
8
8
8
8
8
Print quality or tone is uneven
Half-tone images print unevenly
Cause What to do
Your paper may be moist or 
damp.Do not store paper in a humid or damp 
environment.
The print head is dirty. See “Cleaning the print head” on page 
170 and clean the print head.
There may be no toner left in 
the toner cartridge.If the message on the LCD panel or in 
EPSON Status Monitor 3 indicates that 
the amount of toner left is low, replace 
the toner cartridge. See “Toner 
Cartridge” on page 161.
There may be a problem with 
the photoconductor unit.Replace the photoconductor unit. See 
“Photoconductor Unit” on page 165.
Cause What to do
Your paper may be moist or 
damp.Do not store paper in a humid or damp 
environment. Be sure to use paper that 
is newly unwrapped.
The gradation setting is too 
small when printing graphics.On the Basic Setting menu in the printer 
driver, click More Settings, adjust the 
gradation setting by sliding the 
Contrast slider bar.
There may be no toner left in 
the toner cartridge.If the message on the LCD panel or in 
EPSON Status Monitor 3 indicates that 
the amount of toner is low, replace the 
toner cartridge. See “Toner Cartridge” 
on page 161.
 
						

							202Troubleshooting
Toner smudges
There may be a problem with 
the photoconductor unit.Replace the photoconductor unit. See 
“Photoconductor Unit” on page 165.
The print head is dirty. See “Cleaning the print head” on page 
170 and clean the print head.
Cause What to do
Your paper may be moist or 
damp.Do not store your paper in a humid or 
damp environment.
You may not be using the 
correct type of paper for your 
printer.Epson special paper or smooth, 
high-quality copier paper is 
recommended for best results. See 
“Available paper types” on page 233 for 
information on choosing paper.
The paper path inside the 
printer may be dusty.Clean internal printer components by 
printing three pages with only one 
character per page.
There may be a problem with 
the photoconductor unit.Replace the photoconductor unit. See 
“Photoconductor Unit” on page 165.
Cause What to do
 
						

							Troubleshooting203
8
8
8
8
8
8
8
8
8
8
8
8
Areas are missing in the printed image
Completely blank pages are output
Cause What to do
Your paper may be moist or 
damp.This printer is sensitive to moisture 
absorbed by the paper. The higher the 
moisture content in the paper, the lighter 
the printout. Do not store paper in a 
humid or damp environment.
You may not be using the 
correct type of paper for your 
printer.If the surface of your paper is too rough, 
printed characters may appear distorted 
or broken. Epson special paper or 
smooth, high-quality copier paper is 
recommended for best results. See 
“Available paper types” on page 233 for 
information on choosing paper.
Cause What to do
The printer may have loaded 
more than one sheet at a time.Remove the paper stack and fan it. Tap 
it on a flat surface to even the edges, then 
reload the paper.
There may be no toner left in 
the toner cartridge.If the message on the LCD panel or in the 
Epson Status Monitor 3 indicates that 
the amount of toner is low, replace the 
toner cartridge. See “Toner Cartridge” 
on page 161.
The problem may be with your 
application, interface cable, or 
printer.Confirm the application setting and 
interface connection, and print out a 
status sheet. See “Printing a Status 
Sheet” on page 193. If a blank page is 
ejected, the problem may be with the 
printer. Turn off the printer and contact 
your dealer.
 
						

							204Troubleshooting
The printed image is light or faint
The non-printed side of the page is dirty
The Paper Size setting may be 
incorrect.Make sure the correct paper size is set in 
the Tray Menu on the control panel.
There may be a problem with 
the photoconductor unit.Replace the photoconductor unit. See 
“Photoconductor Unit” on page 165.
Cause What to do
Your paper may be moist or 
damp.Do not store your paper in a humid or 
damp environment.
The Toner Save mode may be 
on.Turn off the Toner Save mode using the 
printer driver.
There may be no toner left in 
the toner cartridge.If the message on the LCD panel or in 
EPSON Status Monitor 3 indicates that 
the amount of toner left is low, replace 
the toner cartridge. See “Toner 
Cartridge” on page 161.
There may be a problem with 
the photoconductor unit.Replace the photoconductor unit. See 
“Photoconductor Unit” on page 165.
The print head is dirty. See “Cleaning the print head” on page 
170 and clean the print head.
Cause What to do
Toner may have spilled onto 
the paper feed path.Clean internal printer components by 
printing three pages with only one 
character per page.
Cause What to do
 
						

							Troubleshooting205
8
8
8
8
8
8
8
8
8
8
8
8
Memory Problems
Print quality decreased
Insufficient memory for current task
Insufficient memory to print all copies
Cause What to do
The printer cannot print at the 
required quality level because 
of insufficient memory, and 
the printer lowers the quality 
automatically so that the 
printer can continue printing.Check to see if the printout is acceptable.
If not, add more memory for a 
permanent solution or lower print 
quality temporarily in the printer driver.
Cause What to do
The printer has insufficient 
memory for current task.Add more memory for a permanent 
solution or lower print quality 
temporarily in the printer driver.
Cause What to do
The printer does not have 
sufficient memory to collate 
print jobs.Only one set of copies will be printed. 
Reduce the contents of print jobs, or add 
more memory. For information on 
installing more memory, see 
“Memory 
Module” on page 155
.
 
						

							206Troubleshooting
Paper Handling Problems
Paper does not feed properly
Cause What to do
The paper guides are not set 
correctly.Make sure that the paper guides in all 
the paper cassettes are set in the correct 
paper size positions.
The paper source setting may 
not be correct.Make sure that you have selected the 
correct paper source in your application.
There may be no paper in the 
cassettes.Load paper into the selected paper 
source.
The size of loaded paper 
differs from the control panel 
setting.Make sure that the correct paper size is 
set in the control panel’s Paper Source 
and MP Tray Size settings.
Too many sheets may be 
loaded in the MP tray or paper 
cassettes.Make sure that you have not tried to load 
too many sheets of paper. For the 
maximum paper capacity for each paper 
source, see “MP tray” on page 23.
The paper that is loaded is 
curled.Straighten the paper.
If paper does not feed from the 
optional paper cassette unit, 
the unit may not be installed 
properly.For instructions on installing the unit, 
see “Optional Paper Cassette Unit” on 
page 146.
 
						

							Troubleshooting207
8
8
8
8
8
8
8
8
8
8
8
8
Problems Using Options
To confirm your options are installed correctly, print a status 
sheet. See “Printing a Status Sheet” on page 193 for details.
Paper does not feed from the optional paper 
cassette
Cause What to do
The optional paper cassette 
may not be installed properly.See “Optional Paper Cassette Unit” on 
page 146 for instructions on installing an 
optional paper cassette unit.
The paper source setting may 
not be correct.Make sure you have selected the proper 
paper source in your application.
There may be no paper in the 
paper cassette.Load paper into the selected paper 
source.
Too many sheets may be 
loaded in the paper cassette.Make sure that you have not tried to load 
too many sheets of paper into the 
cassette. The cassette can hold a 
maximum of 500 sheets of 64 to 105 g/m² 
paper.
The paper size is not set 
correctly.Make sure that the correct paper size is 
selected in the Tray Menu on the control 
panel.
 
						

							208Troubleshooting
Feed jam when using the optional paper 
cassette
An installed option cannot be used
Cause What to do
The paper is jammed at the 
optional paper cassette.See “Clearing Jammed Paper” on page 
176 to clear jammed paper.
Cause What to do
The installed option is not 
defined in the printer driver.For Windows users:
See “Making Optional Settings” on page 
62 to make settings in the printer driver.
For Macintosh users:
When you have attached or removed 
printer options, you need to delete the 
printer using Print Setup Utility (for Mac 
OS X 10.3), Print Center (for Mac OS X 
10.2 or below), or Chooser (for Mac 
OS 9), and then re-register the printer.
 
						

							Troubleshooting209
8
8
8
8
8
8
8
8
8
8
8
8
Correcting USB Problems
If you are having difficulty using the printer with a USB 
connection, see if your problem is listed below, and take any 
recommended actions.
USB connections
USB cables or connections can sometimes be the source of USB 
problems. Try one or both of these solution.
❏For best results, you should connect the printer directly to the 
computer’s USB port. If you must use multiple USB hubs, we 
recommend that you connect the printer to the first-tier hub.
Windows operating system
Your computer must be a model pre-installed with Windows XP, 
Me, 98, 2000, or Server 2003, a model that was pre-installed with 
Windows 98 and upgraded to Windows Me, or a model that was 
pre-installed with Windows Me, 98, 2000, or Server 2003, and 
upgraded to Windows XP. You may not be able to install or run 
the USB printer driver on a computer that does not meet these 
specifications or that is not equipped with a built-in USB port.
For details about your computer, contact your dealer.
Printer software installation
Incorrect or incomplete software installation can lead to USB 
problems. Take note of the following and perform the 
recommended checks to ensure proper installation.
 
						

							210Troubleshooting
Checking printer software installation for Windows 2000, XP, 
or Server 2003
When using Windows XP, 2000, or Server 2003, you must follow 
the steps in the Setup Guide packed with the printer to install the 
printer software. Otherwise, Microsoft’s Universal driver may be 
installed instead. To check if the Universal driver has been 
installed follow the steps below.
1. Open the Printers folder, then right-click the icon of your 
printer.
2. Click Printing Preferences on the shortcut menu that 
appears, then right-click anywhere in the driver.
If About is displayed in the shortcut menu that appears, click 
it. If a message box with the words “Unidrv Printer Driver” 
appears, you must reinstall the printer software as described 
in the Setup Guide. If About is not displayed, the printer 
software has been installed correctly.
Note:
For Windows 2000, if the Digital Signature Not Found dialog box 
appears during the installation process, click Yes. If you click No, you 
will have to install the printer software again.
For Windows XP or Server 2003, if the Software Installation dialog box 
appears during the installation process, click Continue Anyway. If 
you click STOP Installation, you will have to install the printer software 
again.