Home > Electrolux > Washing Machine > Electrolux Ewn 14991 W User Manual

Electrolux Ewn 14991 W User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Electrolux Ewn 14991 W User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 208 Electrolux manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							installationelectrolux  41
    6. Open the porthole and remove the
    polystyrene block fitted on the door
    seal.
    7. Fill the smaller upper hole and the two
    large ones with the corresponding
    plastic plug caps supplied in the bag
    containing the instruction booklet.
    Positioning
    Install the machine on a flat hard floor.
    Make sure that air circulation around the
    machine is not impeded by carpets,
    rugs etc. 
    Check that the machine does not touch
    the wall or other kitchen units. Level the
    washing machine by raising or lowering
    the feet. The feet may be tight to adjust
    as they incorporate a self locking nut,
    but the machine MUST be level and
    stable.
    Any necessary adjustment can be made
    with a spanner. If necessary, check the
    setting with a spirit level. 
    
    
    Accurate levelling prevents vibration,
    noise and displacement of the machine
    during operation. Never place
    cardboard, wood or similar materials
    under the machine to compensate for
    any unevenness in the floor.
    Water inlet
    The appliance must be connected to a
    cold water supply. 
    Do not use the hose from your
    previous machine to connect to the
    water supply.
    Do not place the inlet hose
    downwards. Angle the hose to the
    left or right depending on the
    position of your water tap as
    shown in the picture below.
    Set the hose correctly by loosening the
    ring nut. After positioning the inlet hose,
    be sure to tighten the ring nut again to
    prevent leaks.
    
    
    
    132972252.qxd  27/10/2008  11.32  Pagina  41
     
    						
    							42electrolux 
    Connect the hose to a tap with a 3/4”
    thread. The inlet hose must not be
    lengthened. If it is too short and you do
    not wish to move the tap, you will have
    to purchase a new, longer hose
    specially designed for this type of use.
    Note !
    Installation should comply with
    local water authority and building
    regulations’ requirements.
    The appliance must be connected to a
    cold water supply. 
    A minimum water pressure of 0.05
    MPa (0.5 bar) is required for safe
    operation of the appliance.
    If you cannot make the cold water
    connection direct from the rising mains,
    you may be able to operate the
    appliance from your cold water storage
    system.
    There should be a minimum distance
    of 5.02m (16.5 ft) between the
    appliance’s inlet and the bottom of the
    water storage tank.
    
    Water drainage
    This appliance is designed to be
    permanently plumbed into your homes
    drainage system using one of the
    following methods.
    1.  Into a drainage standpipe.
    Firstly form a hook in the end of the
    drain hose using the «U» piece
    supplied. 
    Place the drain hose into your
    standpipe, which should have an
    internal diameter of approximately
    38mm thus ensuring there is an air
    break between the drain hose and
    standpipe.
    When discharging into a standpipe
    ensure that the top of the standpipe is
    no more than 90 cm (35.4) and no
    less than 60 cm (23.6) above floor
    level.
    The drain hose may be extended to a
    maximum of 4 metres. 
    
    
    
    
    
    
    
    
    
    
    132972252.qxd  27/10/2008  11.32  Pagina  42
     
    						
    							installationelectrolux  43
    An additional drain hose and joining
    piece is available from your local
    Service Force Centre. The joining piece
    must have an internal diameter of 18
    mm.
    If your drain hose looks like this (see
    below) you do not require the «U»
    piece. Just push the hose firmly into
    the standpipe.
    2. Onto a sink outlet spigot.
    If the outlet spigot has not been used
    before, remove any blanking plug that
    may be in place.
    
    
    
    
    
     
    
    
    
    Push the drain hose onto the spigot
    and secure with a clip if required,
    ensure a loop is formed in the drain
    hose (see diagram) to prevent waste
    from the sink entering the washing
    machine.
    Important!
    Before connecting the machine to new
    pipework or to pipework that has not
    been used for some time, run off a
    reasonable amount of water to flush
    out any debris that may have collected
    in the pipes.
    Special conditions
    If the floor is carpeted or covered with
    crumbly or soft material, insert a rigid
    support base under the feet to prevent
    noise, vibration or displacement. The
    base should protrude a few
    centimetres beyond the edges of the
    machine.
    Warning !
    The machine should NOT be placed on
    deep pile carpeting.
    
    
    132972252.qxd  27/10/2008  11.32  Pagina  43
     
    						
    							44electroluxinstallation
    Note
    Please ensure that when the appliance
    is installed it is easily accessible for the
    engineer in the event of a breakdown.
    In the interest of the environment
    Washing machines and dishwashers
    should be connected to the FOUL
    drainage system, the water will then be
    taken to a sewage works for treatment
    before being discharged safely into a
    river. 
    It is essential that these appliances are
    not connected to the surface water
    drainage system as this water is
    discharged directly into a river or stream
    and may cause pollution.
    If you require any further advice please
    contact your local water authority.
    
     
    
     
    !
    
    #$%%
    #%&
    &&
    #
     
    (%#&
    %#&
     
    !
    
    (
    
    
     
    Electrical connection
    Any electrical work required to install
    this appliance should be carried out by
    a qualified electrician or competent
    person.
    Important!
    This appliance must be earthed.
    The manufacturer declines any
    liability should this safety measure
    not be observed.
    Before switching on, make sure the
    electricity supply voltage is the same
    as that indicated on the appliance’s
    rating plate. 
    Important!
    Information on the electrical
    connection is given on the rating
    plate on the inner edge of the
    appliance door.
    The appliance is supplied with a
    13amp plug fitted. In the event of
    having to change the fuse in the plug
    supplied, a 13amp ASTA approved
    (BS1363/A) fuse must be used.
    Should the plug need to be replaced
    for any reason, proceed as described
    below.
    The wires in the mains lead are
    coloured in accordance with the
    following code:
    Green and Yellow ....................-Earth
    Blue ........................................-Neutral
    Brown......................................- Live
    132972252.qxd  27/10/2008  11.32  Pagina  44
     
    						
    							installationelectrolux  45
    The wire coloured green and yellow
    must be connected to the terminal
    marked with the letter «E» or by the
    earth symbol  or coloured green
    and yellow.
    The wire coloured blue must be
    connected to the terminal marked «N»
    or coloured black.
    The wire coloured brown must be
    connected to the terminal marked «L»
    or coloured red.
    Upon completion there must be no cut,
    or stray strands of wire present and the
    cord clamp must be secure over the
    outer sheath.
    Warning!
    A cut off plug inserted into a 13
    amp socket is a serious safety
    (shock) hazard.
    Ensure that the cut off plug is
    disposed of safely. Should the
    appliance power supply cable need
    to be replaced, this must be carried
    out by our Service Force Centre.
    The power supply cable must be easily
    accessible after installing the appliance.
    !##	$ %#&&(
    )(	
    *+*&, )&-#
     
    			
    
    
    Permanent connection
    In the case of permanent connection it
    is necessary that you install a double
    pole switch between the appliance and
    the electricity supply (mains), with a
    minimum gap of 3mm between the
    switch contacts and of a type suitable
    for the required load in compliance with
    the current electrical regulations.
    The switch must not break the yellow
    and green earth cable at any point.
    132972252.qxd  27/10/2008  11.32  Pagina  45
     
    						
    							46electroluxenvironment concerns 
    Environment concerns
    Packaging materials
    The materials marked with the symbol
    are recyclable.
    >PEPSPP
    						
    							guarantee/customer service electrolux47
    Standard guarantee conditions
    We, Electrolux, undertake that if within
    12 months of the date of the purchase
    this Electrolux appliance or any part
    thereof is proved to be defective by
    reason only of faulty workmanship or
    materials, we will, at our option repair
    or replace the same FREE OF
    CHARGE for labour, materials or
    carriage on condition that:
     The appliance has been correctly in-
    stalled and used only on the electri-
    city supply stated on the rating plate.
     The appliance has been used for
    normal domestic purposes only, and
    in accordance with the manufactu-
    rer’s instructions.
     The appliance has not been ser-
    viced, maintained, repaired, taken
    apart or tampered with by any per-
    son not authorised by us.
     Electrolux Service Force Centre must
    undertake all service work under this
    guarantee.
     Any appliance or defective part re-
    placed shall become the Company’s
    property.
     This guarantee is in addition to your
    statutory and other legal rights.
    Exclusions
     Damage or calls resulting from trans-
    portation, improper use or neglect,
    the replacement of any light bulbs or
    removable parts of glass or plastic.
     Costs incurred for calls to put right
    an appliance which is improperly in-
    stalled or calls to appliances outside
    the United Kingdom. Appliances found to be in use within
    a commercial environment, plus tho-
    se which are subject to rental agree-
    ments.
     Products of Electrolux manufacturer
    that are not marketed by Electrolux.
    Service and Spare Parts
    In the event of your appliance requiring
    service, or if you wish to purchase
    spare parts, please contact your local
    Service Force Centre by telephoning
    0870 5 929 929
    Your telephone call will be
    automatically routed to the Service
    Force Centre covering your postcode
    area.For the address of your local
    Service Force Centre and further
    information about Service Force,
    please visit the website at:
    www.serviceforce.co.uk
    Before calling out an engineer, please
    ensure you have read the details under
    the heading “Something not working”
    When you contact the Service Force
    Centre you will need to give the follo-
    wing details:
    1. Your name, address and postcode.
    2. Your telephone number.
    3. Clear concise details of the fault.
    4. The model and Serial number of the
    appliance (found on the rating plate).
    5. The purchase date.
    Please note a valid purchase receipt or
    guarantee documentation is required
    for in guarantee service calls.
    132972252.qxd  27/10/2008  11.32  Pagina  47
     
    						
    							48electroluxguarantee/customer service 
    Customer Care
    For general enquiries concerning your
    Electrolux appliance, or for further infor-
    mation on Electrolux products please
    contact our Customer Care
    Department by letter or telephone at
    the address below or visit our website
    at:
    www.electrolux.co.uk
    Customer Care Department Electrolux
    Major Appliances
    Addington Way 
    Luton
    Bedfordshire, LU4 9QQ
    Tel: 08705 950 950 (*)
    (*)Calls may be recorded for training
    purposesEuropean Guarantee
    This appliance is guaranteed by
    Electrolux in each of the countries
    listed at the back of this user manual,
    for the period specified in the appliance
    guarantee or otherwise by law.  
    If you move from one of these
    countries to another of the countries
    listed below the appliance guarantee
    will move with you subject to the
    following qualifications:
     The appliance guarantee starts from
    the date you first purchased the
    appliance which will be evidenced by
    production of a valid purchase
    document issued by the seller of the
    appliance. 
     The appliance guarantee is for the
    same period and to the same extent
    for labour and parts as exists in your
    new country of residence for this
    particular model or range of
    appliances. 
     The appliance guarantee is personal
    to the original purchaser of the
    appliance and cannot be transferred
    to another user. 
     The appliance is installed and used in
    ac-cordance with instructions issued
    by Electrolux and is only used within
    the home, i.e. is not used for
    commercial purposes. 
     The appliance is installed in
    accordance with all relevant
    regulations in force within your new
    country of residence. 
    The provisions of this European
    Guarantee do not affect any of the
    rights granted to you by law. 
    132972252.qxd  27/10/2008  11.32  Pagina  48
     
    						
    							Customer Service Centres
    Should you need further assistance please contact your local Customer Service
    Centre
    www.electrolux.com
    à
    Albania+35 5 4 261 450Rr. Pjeter Bogdani Nr. 7 Tirane
    Belgique/België/Belgien+32 2 363 04 44Bergensesteenweg 719, 1502 Lembeek
    Česká republika+420 2 61 12 61 12Budějovická 3, Praha 4, 140 21
    Danmark+45 70 11 74 00Sjællandsgade 2, 7000 Fredericia
    Deutschland+49 180 32 26 622Muggenhofer Str. 135, 90429 Nürnberg
    Eesti+37 2 66 50 030Mustamäe tee 24, 10621 Tallinn 
    España+34 902 11 63 88Carretera M-300, Km. 29,900 Alcalá de Henares  Madrid
    Francewww.electrolux.fr
    Great Britain+44 8705 929 929Addington Way, Luton, Bedfordshire LU4 9QQ
    Hellas+30 23 10 56 19 704, Limnou Str., 54627 Thessaloniki
    Hrvatska+38 51 63 23 338Slavonska avenija 3, 10000 Zagreb
    Ireland+353 1 40 90 753Longmile Road Dublin 12
    Italia+39 (0) 434 558500C.so Lino Zanussi, 26 - 33080 Porcia (PN)
    Latvija+37 17 84 59 34Kr. Barona iela 130/2, LV-1012, Riga
    Lituania+370 5 27 80 609Verkiu, 2 9, 09108 Vilnius, Lithuania
    Luxembourg+35 2 42 43 13 01Rue de Bitbourg, 7, L-1273 Hamm
    Magyarország+36 1 252 1773H-1142 Budapest XIV, Erzsébet királyné útja 87
    Nederland+31 17 24 68 300Vennootsweg 1, 2404 CG - Alphen aan den Rijn
    Norge+47 81 5 30 222Risløkkvn. 2 , 0508 Oslo
    Österreich +43 18 66 400Herziggasse 9, 1230 Wien
    Polska+48 22 43 47 300ul. Kolejowa 5/7, Warsaw
    Portugal+35 12 14 40 39 39Quinta da Fonte - Edificio Gonçalves Zarco - Q35 -2774-518 Paço de Arcos
    Romania+40 21 451 20 30Str. Garii Progresului 2, S4, 040671 RO
    Schweiz-Suisse-Svizzera+41 62 88 99 111Industriestrasse 10, CH-5506 Mägenwil
    Slovenija+38 61 24 25 731Tr aška 132, 1000 Ljubljana
    Slovensko+421 2 43 33 43 22Electrolux Slovakia s.r.o., Electrolux Domáce spotrebiče SK, Seberíniho 1, 821 03 Bratislava
    Suomiwww.electrolux.fi
    Sverige+46 (0)771 76 76 76Electrolux Service, S:t Göransgatan 143, S-105 45 Stockholm
    Türkiye+90 21 22 93 10 25Tarlabașicaddesi no : 35 Taksim Istanbul
    Россия+7 095 937 7837129090Москва, Олимпийский проспект, 16, БЦ “Олимпик”
    electrolux  49
    132972252.qxd  27/10/2008  11.32  Pagina  49
     
    						
    							50electrolux
    132972252.qxd  27/10/2008  11.32  Pagina  50
     
    						
    All Electrolux manuals Comments (0)

    Related Manuals for Electrolux Ewn 14991 W User Manual