Electrolux Ewf 86110 W User Manual

							degree of hardness is soft, readjust the quan-
tity of the detergent.
Washing programmes
Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
COTTONS 95°-60°
Main wash - Rinses
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg - Red. load 3 kg
For white and fast coloured cottons (heavily and nor-
mally soiled items).
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
DAILY
SUPER QUICK
1)
EXTRA RINSE
 2)
COTTONS ECONOMY  60°
Main wash - Rinses
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg
For white and fast coloured cotton (normally soiled
items)
This programme can be selected for slightly or normally
soiled cotton items. The temperature will decrease and the
washing time will be extended. This allows to obtain a good
washing efficiency so saving energy.
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
EXTRA RINSE 2)
COTTONS ECONOMY  40°
Main wash - Rinses
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg
For coloured cotton (lightly soiled items).
This programme can be selected for slightly or normally
soiled cotton items. The temperature will decrease and the
washing time will be extended. This allows to obtain a good
washing efficiency so saving energy.
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
EXTRA RINSE 2)
COTTONS 40°- COLD
Main wash - Rinses
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg - Red. load 3 kg
For coloured cottons (lightly soiled items).
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
DAILY
SUPER QUICK 
1)
EXTRA RINSE
 2)
electrolux  11
 
						

							Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
SYNTHETICS 60°- COLD
Main wash - Rinses
Maximum spin speed 900 rpm or 800 rpm - depending on
a model
Max. load 3 kg - Red. load 1,5 kg
Synthetic or mixed fabrics: underwear, coloured gar-
ments, non-shrink shirts, blouses.
SPIN
NIGHT CYCLE
RINSE HOLD
PREWASH
DAILY
SUPER QUICK 
1)
EXTRA RINSE
 2)
DELICATES 40°-30°
Main wash - Rinses
Maximum spin speed 700 rpm
Max. load 3 kg- Red. load kg 1,5
Delicate fabrics: acrylics, viscose, polyester.
SPIN (only for model
EWF 86110W)
NIGHT CYCLE
RINSE HOLD
PREWASH
DAILY
SUPER QUICK 
1)
EXTRA RINSE
 2)
HANDWASH/WOOL   40° - COLD
Main wash - Rinses
Maximum spin speed 800/900/1000 rpm - depending on a
model)
Max. load 2 kg
Washing programme for machine washable wool as well as
for hand washable woollens and delicate fabrics with «hand
washing» care symbol. Note  : A single or bulky item may
cause imbalance. If the appliance doesn’t perform the final
spin phase, add more items, redistribute the load manually
and then select the spinning programme.
SPIN
NIGHT CYCLE
RINSE HOLD
RINSE
Rinses
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg
With this programme it is possible to rinse and spin cotton
garments which have been washed by hand. To intensify the
rinsing action, select the option EXTRA RINSE. The appli-
ance will add some additional rinses.
SPIN
NIGHT CYCLE
RINSE HOLD
EXTRA RINSE
DRAIN Draining of water
Max. load 6 kg
For emptying out the water of the last rinse in programmes
with the Night Cycle and Rinse Hold option selected.
  
12  electrolux
 
						

							Programme
Maximum and Minimum Temperature
Cycle Description
Maximum Spin Speed
Maximum Fabrics Load
Type of Laundry
OptionsDetergent
Compartment
SPIN Drain and long spin
Long spin at maximum spin speed (800/1000/1200 rpm
depending on a model)
Max. load 6 kg
Separate spin for hand washed garments and after pro-
grammes with the Rinse Hold and Night Cycle option se-
lected. You can choose the spin speed by pressing the rel-
evant button to adapt it to the fabrics to be spun.
SPIN 
MINI 30°
Main wash - Rinses - Short spin
Maximum spin speed 700 rpm
Max. load 3 kg
Ideal for laundry which is lightly soiled or which only needs
freshening up.
SPIN (only for model
EWF 86110W)
 = OFF
For cancelling the programme which is running or to switch the machine off .
1) If you select the Super Quick option by pressing button 3 , we recommend that you reduce the maximum load as
indicated. (Red. load = reduced load). Full loading is possible however with somewhat reduced cleaning results.
2) If using liquid detergent, a programme without PREWASH must be selected.
Care and cleaning
Warning! You must disconnect the
appliance from the electricity supply,
before you can carry out any cleaning or
maintenance work.
Descaling
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder manufac-
turers instructions. This will help to prevent
the formation of lime deposits.
After each wash
Leave the door open for a while. This helps
to prevent mould and stagnant smells form-
ing inside the appliance. Keeping the door
open after a wash will also help to preserve
the door seal.Maintenance wash
With the use of low temperature washes it is
possible to get a build up of residues inside
the drum.
We recommend that a maintenance wash be
performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash pro-
gramme.
• Use a normal measure of detergent, must
be a powder with biological properties.
External cleaning
Clean the exterior cabinet of the appliance
with soap and water only, and then dry thor-
oughly.
Important! Do not use methylated spirits,
solvents or similar products to clean the
cabinet.
electrolux  13
 
						

							Cleaning the dispenser drawer
The detergent dispenser drawer should be
cleaned regularly.
1. Remove the detergent dispenser drawer
by pulling it firmly. Remove any traces of
accumulated powder. To aid cleaning,
the top part of the additive compartment
should be removed.
2. Remove the conditioner insert from the
appropriate compartment.
3. Clean all parts with water.
4. Put the conditioner insert in as far as it will
go, so that it is firmly in place
5. Clean all parts of the machine, especially
the nozzles in the top of the washing-in
chamber, with a brush.
6. Insert the detergent dispenser drawer in
the guide rails and push it in.
Washing drum
Rust deposits in the drum may occur due to
rusting foreign bodies in the washing or tap
water containing iron.
Important! Do not clean the drum with
acidic descaling agents, scouring agents
containing chlorine or iron or steel wool.
1. Remove any rust deposits on the drum
with a cleaning agent for stainless steel.
2. Run a washing cycle without any washing
to clean off any cleaning agent residues.
Programme: Short Cotton Programme at
maximum temperature and add approx.
1/4 measuring cup of detergent.
Door seal
Check from time to time the door seal and
eliminate eventual possible objects that
could be trapped in the fold.
14  electrolux
 
						

							Drain pump
The pump should be inspected regularly and
particularly if:
• the machine does not empty and/or spin
• the machine makes an unusual noise dur-
ing draining due to objects such as safety
pins, coins etc. blocking the pump.
Proceed as follows:
1. Disconnect the appliance.
2. If necessary wait until the water has
cooled down.
3. Open the pump door.
4. Place a container close to the pump to
collect any spillage.
5. Release the emergency emptying hose,
place it in the container and remove its
cap cover.
6. When no more water comes out, un-
screw the pump and remove it. Alwayskeep a rag nearby to dry up spillage of
water when removing the pump.
7. Remove any objects from the pump im-
peller by rotating it.
8. Refit the cap on the emergency empty-
ing hose and place the latter back in its
seat.
9. Screw the pump fully in.
10. Close the pump door.
Warning!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump. Never remove the pump
cover during a wash cycle, always wait until
the appliance has finished the cycle, and is
empty. When replacing the cover, ensure it
is securely retightened so as to stop leaks
and young children being able to remove it.
electrolux  15
 
						

							Cleaning the water inlet filters
If you notice that the machine is taking longer
to fill, check that the filter in the water inlet
hose is not blocked.
1. Turn off the water tap.
2. Unscrew the water inlet hose.
3. Clean the filter in the hose using a hard
bristle brush.
4. Screw the hose back onto the tap.
5. Unscrew the hose from the machine.
Keep a rug nearby because some water
may flow.
6. Clean the filter in the valve with a stiff
brush or with the piece of cloth.
7. Screw the hose back to the machine and
make sure the connection is tight.
8. Turn on the water tap.Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
1. pull out the plug from the power socket;
2. close the water tap;
3. if necessary, wait until the water has
cooled down;
4. open the pump door;
5. place a bowl on the floor and place the
end of the emergency emptying hose into
the bowl. Remove its cap. The water
should drain by gravity into the bowl.
When the bowl is full, put the cap back
on the hose. Empty the bowl. Repeat the
procedure until water stops flowing out;
6. clean the pump if necessary as previously
described;
7. replace the emergency emptying hose in
its seat after having plugged it;
8. screw the pump again and close the
door.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, proceed
as follows:
1. close the water tap and unscrew the wa-
ter inlet hose from the tap;
2. place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain
out;
3. screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
By doing this, any water remaining in the ma-
chine is removed, avoiding ice forming and
consequently damage to the appliance.
When you use the machine again, make sure
that the ambient temperature is above 0°C.
Important! Every time you drain the water
through the emergency emptying hose you
must pour 2 litres of water into the main wash
compartment of the detergent drawer and
then run the drain programme. This will
activate the ECO Valve device avoiding that
part of the detergent remains unused at next
washing.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
16  electrolux
 
						

							solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that
the red pilot light of button 5 blinks to indi-
cate that the machine is not working.Once the problem has been eliminated,
press the button 5 to restart the programme.
If after all checks, the problem persists, con-
tact your local Service Centre.
ProblemPossible cause/Solution
The washing machine does
not start:
The door has not been closed (the button 5 red light blinks).
•Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The programme selector dial is not correctly positioned and the but-
ton 5 has not been pressed.
• Please turn the selector dial and press the button 5 again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay start.
The machine does not fill:
The water tap is closed (the button 5 red light blinks).
•Open the water tap.
The inlet hose is squashed or kinked(the button 5 red light blinks).
• Check the inlet hose connection.
The filter in the inlet hose or the inlet valve filter are blocked (the
button 5 red light blinks).
• Clean the water inlet filters (See Cleaning the water inlet filters
for more details).
The door is not properly closed (the button 5 red light blinks).
•Close the door firmly.
The machine fills then emp-
ties immediately:The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage» section.
The machine does not emp-
ty and/or does not spin:
The drain hose is squashed or kinked (the button 5 red light blinks).
• Check the drain hose connection.
The drain filter is clogged (the button 5 red light blinks).
• Clean the drain filter.
An option or a programme that ends with the water still in the tub or
a that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fittings.
It is not always easy to see this as the water runs down the hose;
check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Replace it with a new one.
The cap on the emergency emptying hose has not been replaced
or the filter has not been properly screwed in after cleaning action.
• Refit the cap on the emergency emptying hose or screw the filter
fully in.
electrolux  17
 
						

							ProblemPossible cause/Solution
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the light 7.2 has gone out.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can re-
sume. If, after 10 minutes, the laundry is still not evenly distributed
in the drum, the machine will not spin. In this case, redistribute the
load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
The machine makes an un-
usual noise:The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor en-
sures a softer start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of the machine.
No water is visible in the
drum:Machines based on modern technology operate very economically
using very little water without affecting performance.
18  electrolux
 
						

							If you are unable to identify or solve the prob-
lem, contact our service centre. Before tele-
phoning, make a note of the model, serial
number and purchase date of your machine:
the Service Centre will require this informa-
tion.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Mod. ..
. ... ...
Prod. No.
 ..
. ... ..
         
      
         
 Ser.  N
o. ... ...
 ...
Technical data
DimensionsWidth
Height
Depth
Depth (Overall dimensions)60 cm
85 cm
60 cm
63 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating plate,
on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton6 kg
Spin SpeedMaximum800 rpm (EWF 86110W)
1000 rpm (EWF106110W)
1200 rpm (EWF 126110W)
Consumption values
ProgrammeEnergy consumption
(KWh)Water consumption
(litres)Programme duration
(Minutes)
White Cottons 95°261135
Cottons 60°1.358125
Cotton ECO 60° 1)1.0246150
Cottons 40°0.758120
Synthetics 40°0.55080
Delicates 40°0.556065
Wool/ Handwash 30°0.255355
1) «Cottons Eco» at 60°C with a load of 6 kg is the reference programme for the data entered in the energy label, in
compliance with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it
may vary depending on the quantity and type of laundry, on the inlet water temperature
and on the ambient temperature.
electrolux  19
 
						

							Installation
Unpacking
All transit bolts and packing must be re-
moved before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining and inlet hose from the hose
holders on the rear of the appliance.
3. Unscrew the three bolts.4. Slide out the relevant plastic spacers.
5. Fill the smaller upper hole and the two
large ones with the corresponding plastic
plug caps supplied in the bag containing
the instruction booklet.
20  electrolux