Electrolux Ewc 1150 User Manual

							REMOVING STAINS
Stubborn stains may not be removed by
just water and detergent. It is therefore ad-
visable to treat them prior to washing.
Blood: treat fresh stains with cold water.
For dried stains, soak overnight in water
with a special detergent then rub in the
soap and water.
Oil based paint: moisten with benzine
stain remover, lay the garment on a soft
cloth and dab the stain; treat several times.
Dried grease stains: moisten with turpen-
tine, lay the garment on a soft surface and
dab the stain with the fingertips and a cot-
ton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since
the cellulose structure will already have
been damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone
1), lay the garment on a soft cloth
and dab the stain.
Lipstick: moisten with acetone as above,
then treat stains with methylated spirits.
Treat any residual marks with bleach.
Red wine: soak in water and detergent,
rinse and treat with acetic or citric acid,
then rinse. Treat any residual marks with
bleach.
Ink: depending on the type of ink, moisten
the fabric first with acetone
1), then with
acetic acid; treat any residual marks on
white fabrics with bleach and then rinse
thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
DETERGENTS AND ADDITIVES
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment.Although biodegradable, detergents contain
substances which, in large quantities, can
upset the delicate balance of nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine
detergents may be used in this appliance:
• powder detergents for all types of fabric
• powder detergents for delicate fabrics
(60°C max) and woollens
• liquid detergents, preferably for low tem-
perature wash programmes (60°C max)
for all types of fabric, or special for wool-
lens only.
The detergent and any additives must be
placed in the appropriate compartments of
the dispenser drawer before starting the
wash programme.
Prewash detergent is to be added
straight into the drum
If using liquid detergents, a programme
without prewash must be selected. Pour
the liquid detergent into the detergent com-
partment immediately before you start the
programme.
Your appliance incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Follow the product manufacturer’s recom-
mendations on quantities to use and do
not exceed the «MAX» mark in the de-
tergent dispenser drawer.
DEGREES OF WATER HARDNESS
Water hardness is classified in so-called
“degrees” of hardness. Information on hard-
ness of the water in your area can be ob-
tained from the relevant water supply com-
pany, or from your local authority. If the wa-
ter hardness degree is medium or high we
suggest you to add a water softener follow-
ing always the manufacturer’s instructions.
When the degree of hardness is soft, read-
just the quantity of the detergent.
1) do not use acetone on artificial silk
electrolux 11
 
						

							WASHING PROGRAMMES
Programme/ Tem-
peratureType of laundryOptionsDescription of the
programme
 WHITE COTTON
90°White cotton (heavily
and normally soiled
cotton items)SPIN REDUCTION/
RINSE HOLD - DELAY
START- PREWASH -
QUICK
1) - SUPER
RINSE
Main wash
Rinses
Long spin max. 1100
rpm
Max load 3 kg
Red. load 2 kg
 COTTON E 2)
60°
White cotton econo-
my
(This programme can
be selected for slightly
or normally soiled cot-
ton items. The temper-
ature will decrease and
the washing time will
be extended. This al-
lows to obtain a good
washing efficiency so
saving energy.)
SPIN REDUCTION/
RINSE HOLD - DELAY
START- PREWASH -
SUPER RINSEMain wash
Rinses
Long spin max. 1100
rpm
Max load 3 kg
 COLOURED COT-
TON
60° - 30°Coloured cotton
(heavily and normally
soiled cotton items)SPIN REDUCTION/
RINSE HOLD - DELAY
START- PREWASH -
QUICK 
1) - SUPER
RINSE
Main wash
Rinses
Long spin max. 1100
rpm
Max load 3 kg
Red. load 2 kg
 COTTON E 2)
40°
Coloured cotton
economy
(Cotton economy pro-
gram. See: Cotton 60°
E)SPIN REDUCTION/
RINSE HOLD - DELAY
START- PREWASH -
SUPER RINSEMain wash
Rinses
Long spin max. 1100
rpm
Max load 3 kg
 SYNTHETIC
40°-30°
Synthetic or mixed
fabrics: underwear,
coloured garments,
non-shrink shirts, blou-
ses.SPIN REDUCTION/
RINSE HOLD - DELAY
START- PREWASH -
QUICK 
1)- SUPER
RINSE
Main wash
Rinses
Short spin max. 900
rpm
Max Load 1,5 kg
 DELICATE
40°Delicate fabrics:
acrylics, viscose, poly-
ester.SPIN REDUCTION/
RINSE HOLD - DELAY
START - PREWASH -
SUPER RINSEMain wash
Rinses
Short spin max. 700
rpm
Max Load 1,5 kg
 HANDWASH
30°Special programme for
delicate fabrics with
«hand washing» care
symbol.SPIN REDUCTION/
RINSE HOLD - DELAY
STARTMain wash
Rinses
Short spin max. 900
rpm
Max Load 1 kg
 WOOL
40°-COLD
Washing programme
for machine washable
wool as well as for
hand washable wool-
lens and delicate fab-
rics.
SPIN REDUCTION/
RINSE HOLD - DELAY
STARTMain wash
Rinses
Short spin max. 900
rpm
Max Load 1 kg
12 electrolux
 
						

							Programme/ Tem-
peratureType of laundryOptionsDescription of the
programme
MINI
30°For lightly soiled laun-
dry or for laundry
which needs freshen-
ing up.SPIN REDUCTION/
RINSE HOLD - DELAY
STARTMain wash
Rinses
Short spin max. 700
rpm
Max Load 1,5 kg
 RINSES
With this programme it
is possible to rinse and
spin cotton garments
which have been
washed by hand. The
machine performs 3
rinses, followed by a fi-
nal long spin. The spin
speed can be re-
duced.
SPIN REDUCTION/
RINSE HOLD - SUPER
RINSERinses
Spin max. 1100 rpm
Max Load 3 kg
 DRAIN
For emptying out the
water of the last rinse
in programmes with
the Rinse Hold or No
Spin option selected.
 Draining of water
Max Load 3 kg
 SPIN
Separate spin for hand
washed garments and
after programmes with
the Rinse Hold option
selected. You can
choose the spin speed
by turning the spin
speed selector to
adapt it to the fabrics
to be spun.
SPIN REDUCTION
Drain and long spin
Max. spin speed 1100
rpm
Max Load 3 kg
 /OFFFor resetting the pro-
gramme or switching
the machine off  
1) If you select this option, we recommend that you reduce the maximum load as indicated. (Red. load= reduced
load). Full loading is possible however with somewhat reduced cleaning results.
2) Standard programmes for the Energy Label consumption values
According to regulation 1061/2010, the “COTTON E 60 °C” and “COTTON E 40 °C” are respectively the
“standard 60 °C cotton programme” and the “standard 40 °C cotton programme”. They are the most efficient
programmes in terms of combined energy and water consumptions for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected pro-
gramme.
CARE AND CLEANING
Important! You must DISCONNECT the
appliance from the electricity supply, before
you can carry out any cleaning or
maintenance work.
DESCALING
The water we use normally contains lime. It
is a good idea to periodically use a water
softening powder in the machine. Do thisseparately from any laundry washing, and
according to the softening powder manu-
facturers instructions. This will help to pre-
vent the formation of lime deposits.
MAINTENANCE WASH
With the use of low temperature washes it
is possible to get a build up of residues in-
side the drum.
electrolux 13
 
						

							We recommend that a maintenance wash
be performed on a regular basis.
To run a maintenance wash:
• The drum should be empty of laundry.
• Select the hottest cotton wash pro-
gramme.
• Use a normal measure of detergent,
must be a powder with biological proper-
ties.
EXTERNAL CLEANING
Clean the exterior cabinet of the appliance
with soap and water only, and then dry
thoroughly.
CLEANING THE DISPENSER DRAWER
The washing powder and additive dispens-
er drawer should be cleaned regularly.
1. If necessary, the whole detergent draw-
er can be taken out of the machine for
cleaning. You need to pull it firmly out-
wards, so that it comes free of retaining
stop.2. To remove the siphon at the inside
edge of the drawer for cleaning, you
need to press it inwards and pull it up-
wards at the same time. Flush it out un-
der a tap, to remove any traces of ac-
cumulated powder. When you put it
back, press it downwards until you
hear a distinct click.
CLEANING THE DRAWER RECESS
Having removed the drawer, use a small
brush to clean the recess, ensuring that all
washing powder residue is removed from
the upper and lower part of the recess.
Replace the drawer and run the rinse pro-
gramme without any clothes in the drum.
CLEANING THE WATER INLET FILTER
If your water is very hard or contains traces
of lime deposit, the water inlet filter may be-
come clogged. It is therefore a good idea to
clean it from time to time.
Turn off the water tap. Unscrew the water
inlet hose. Clean the filter using a hard bris-
tle brush. Tighten up the inlet hose.
14 electrolux
 
						

							THE DANGERS OF FREEZING
If the machine is exposed to temperatures
below 0°C, certain precautions should be
taken.
• Turn off the water supply.
• Unscrew the inlet hose from the supply
tap.
• Select a wash programme, start the ma-
chine and let the programme run for a
short time.• Interrupt the programme by turning the
programme selector to 
 position.
• Place the end of inlet and drain hoses
down low, into the waste gully (floor
drain) set into the floor. Make sure that
the end of the hose does not go below
the water level in the gullys (drains) wa-
ter tap.
• Select the programme Drain and let it
run until it is finished.
•
Turn the programme selector to 
 posi-
tion. When you intend to start the ma-
chine up again, make sure that the room
temperature is above 0 °C.
The appliance is only to be used and stored
indoors at normal room temperature. The
manufacturer is not responsible for any
frost damage.
WHAT TO DO IF…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engi-
neer. Before contacting your local Service
Centre, please carry out the checks listed
below.
During machine operation it is possible that
the End pilot light blinks to indicate that the
machine is not working:•1 flash: problem with the water supply.
•2 flashes: problem with the water drain-
ing.
•4 flashes: door open.
Once the problem has been eliminated,
press the button START to restart the pro-
gramme. If after all checks, the problem
persists, contact your local Service Centre.
ProblemPossible cause/Solution
The machine does not start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button Start
has not been pressed.
• Please turn the selector dial and press the button Start again.
The delay start has been selected.
• If the laundry are to be washed immediately, cancel the delay
start.
electrolux 15
 
						

							ProblemPossible cause/Solution
The machine does not fill:
The water tap is closed.
• Open the water tap.
The inlet hose is squashed or kinked.
• Check the inlet hose connection.
The filter in the inlet hose is blocked.
• Clean the water inlet hose filter.
The door is not properly closed.
• Close the door firmly.
The machine fills then emp-
ties immediately:The end of the drain hose is too low.
• Refer to relevant paragraph in «Installation» chapter.
The machine does not
empty and/or does not
spin:
The drain hose is squashed or kinked.
• Check the drain hose connection.
An option or a programme that ends with the water still in the tub
or that eliminates all the spinning phases has been selected.
• Select the draining or spinning programme.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
There is water on the floor:
Too much detergent or unsuitable detergent (creates too much
foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the inlet hose fit-
tings. It is not always easy to see this as the water runs down the
hose; check to see if it is damp.
• Check the water inlet hose connection.
The drain or inlet hose is damaged.
• Change it with a new one.
Unsatisfactory washing re-
sults:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait until the indicator light for door locked has gone out.
There is water in the drum.
• Select drain or spin programme to empty out the water.
The machine vibrates is
noisy:
The transit bolts and packing have not been removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted
• Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
16 electrolux
 
						

							ProblemPossible cause/Solution
Spinning starts late or the
machine does not spin:
The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is redis-
tributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not evenly distrib-
uted in the drum, the machine will not spin. In this case ,redistrib-
ute the load manually and select the spin programme.
• Redistribute the laundry.
The load is too small.
• Add more items, redistribute the load manually and then select
the spinning programme.
No water is visible in the
drum:Machines based on modern technology operate very economically
using very little water without affecting performance.
If you are unable to identify or solve the
problem, contact our service centre. Before
telephoning, make a note of the model, se-
rial number and purchase date of your ma-
chine: the Service Centre will require this in-
formation.
Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
TECHNICAL DATA
DimensionsWidth
Height
Depth50 cm
67 cm
55 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating
plate, on the inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton3 kg
Spin SpeedMaximum1100 rpm
CONSUMPTION VALUES
The data of this table are approximate. Different causes can change the data: the
quantity and type of laundry, the water and ambient temperature.
electrolux 17
 
						

							ProgrammesLoad
(kg)Energy con-
sumption
(kWh)Water con-
sumption (li-
tre)Approximate
programme
duration (mi-
nutes)Remaining
moisture
(%)
1)
Cottons 60 °C30.94512053
Cottons 40 °C30.454511053
Synthetics 40 °C1,50.5508035
Delicates 40 °C1,50.5527035
Wool/Hand wash
30 °C10.3607530
Standard cotton programmes 
Standard 60 °C
cotton30.590000035
Standard 60 °C
cotton1,50.540000035
Standard 40 °C
cotton1,50.490000035
1) At the end of spin phase.
Off Mode (W)Left On Mode (W)
0.101.10
INSTALLATION
LIFTING THE MACHINE
Be careful when lifting the machine. Incor-
rect methods of lifting can cause physical
injuries and also increase the risk of dam-
age to the machine. Open the door and
take hold of the top inside of the door
opening. You can also lift the machine by
gripping the rear overhang of the top.
Warning! Never lift the machine by
gripping it’s control panel, door, or
detergent dispenser.UNPACKING
When supplied the washing machine is
packed using a number of locking devices/
packing pieces to prevent drum and motor
from damage in transit All transit bolts and
packing must be removed before using the
appliance.
You are advised to keep all transit devices
so that they can be refitted if the machine
ever has to be transported again.
18 electrolux
 
						

							1. Spread some of the polystyrene pack-
aging materials on the floor behind the
machine and then lay the machine
carefully rear side down on them. Make
sure that no hoses are crushed in the
process. Remove the polystyrene base
from the bottom of the appliance.
2. Return machine to its upright position
and remove the power supply cable
and the draining and inlet hose from the
hose holders on the rear of the appli-
ance.
3. With a suitable spanner unscrew and
remove the three screws and their
spacers on machines rear.
4. The three holes must then be plugged
with the plastic plug caps supplied in
the bag containing the instruction
booklet, which can be found inside the
drum.
POSITIONING
Install the machine on a flat hard floor.
Make sure that air circulation around the
machine is not impeded by carpets, rugs
etc. Check that the machine does not
touch the wall or furniture. Level the wash-
ing machine by raising or lowering the two
front feet. If necessary, check the setting
with a spirit level. Any necessary adjustment
can be made with a spanner. Accurate lev-
elling prevents vibration, noise and dis-
placement of the machine during operation.
electrolux 19
 
						

							Caution! Never place cardboard,
wood or similar materials under the
machine to compensate for any
unevenness in the floor.
WATER INLET
Warning! This appliance must be
connected to a cold water supply.1. Connect the water inlet hose supplied
with the machine to a tap with a 3/4
thread. Always use the hose supplied
with the appliance.
If necessary, use the suitable or sup-
plied restrictor (1/2”).
Important! Do not use the hose from
your previous machine to connect to
the water supply.
2. The machine end of the inlet hose can
be turned in any direction. Set the hose
correctly by loosening the ring nut. Af-
ter positioning the inlet hose, be sure to
tighten the ring nut again to prevent
leaks.
20 electrolux