Electrolux Esl 65070 User Manual

							Make sure that there is detergent
in the detergent dispenser before
you start a new programme.
At the end of the programme
When the programme is completed, an
intermittent acoustic signal operates and
the end indicator comes on.
1.Press the on/off button to deactivate
the appliance.
2.Close the water tap.
If you do not press the on/off but-
ton, the Auto Off function auto-
matically deactivates the appli-ance after some minutes. This
helps to decrease the energy con-
sumption.
Important
• Let the dishes become cold before you
remove them from the appliance. Hot
dishes can be easily damaged.
• First remove the items from the lower
basket, then from the upper basket.
• There can be water on the sides and on
the door of the appliance. Stainless
steel becomes cool more quickly than
the dishes.
8. HINTS AND TIPS
8.1 The water softener
Hard water contains a high quantity of
minerals that can cause damage to the
appliance and bad washing results. The
water softener neutralises these minerals.
The dishwasher salt keeps the water soft-
ener clean and in good conditions. It is
important to set the right level of the water
softener. This makes sure that the water
softener uses the correct quantity of dish-
washer salt and water.
8.2 Using salt, rinse aid and
detergent
• Only use salt, rinse aid and detergent
for dishwasher. Other products can
cause damage to the appliance.
• The rinse aid helps, during the last rins-
ing phase, to dry the dishes without
streaks and stains.
• Combi detergent tablets contain deter-
gent, rinse aid and other added agents.
Be sure that these tablets are applica-
ble to the water hardness in your area.
Refer to the instructions on the packag-
ing of the products.
• Detergent tablets do not fully dissolve
with short programmes. To prevent de-
tergent residues on the tableware, we
recommend that you use the tablets
with long programmes.
Do not use more than the correct
quantity of detergent. Refer to the
instructions on the detergent
packaging.
8.3 Loading the baskets
Refer to the supplied leaflet with
examples of the load of the bas-
kets.
• Only use the appliance to wash items
that are dishwasher-safe.
• Do not put in the appliance items made
of wood, horn, aluminium, pewter and
copper.
• Do not put in the appliance items that
can absorb water (sponges, household
cloths).
• Remove remaining food from the items.
• To remove easily remaining burned
food, soak pots and pans in water be-
fore you put them in the appliance.
• Put hollow items (cups, glasses and
pans) with the opening down.
• Make sure that cutlery and dishes do
not bond together. Mix spoons with
other cutlery.
• Make sure that glasses do not touch
other glasses.
• Put the small items in the cutlery bas-
ket.
• Put the light items in the upper basket.
Make sure that they do not move.
ENGLISH 11
 
						

							• Make sure that the spray arms can
move freely before you start a pro-
gramme.
8.4 Before starting a
programme
Make sure that:
• The filters are clean and correctly instal-
led.
• The spray arms are not clogged.• The position of the items in the baskets
is correct.
• The programme is applicable for the
type of load and for the degree of soil.
• The correct quantity of detergent is
used.
• There is dishwasher salt and rinse aid
(unless you use combi detergent tab-
lets).
• The cap of the salt container is tight.
9. CARE AND CLEANING
WARNING!
Before maintenance, deactivate
the appliance and disconnect the
mains plug from the mains socket.Dirty filters and clogged spray
arms decrease the washing re-
sults.
Make a check regularly and, if
necessary, clean them.
9.1 Cleaning the filters
A
B
C
C1.Turn the filter (A) counterclockwise
and remove it.
A1
A2
2.To disassemble the filter (A), pull
apart (A1) and (A2).
3.Remove the filter (B).
4.Wash the filters with water.
5.Put the filter (B) to its initial position.
Make sure that it assembles correctly
under the two guides (C).
12www.electrolux.com
 
						

							6.Assemble the filter (A) and put it into
position in filter (B). Turn it clockwise
until it locks.
An incorrect position of the filters
can cause bad washing results
and damage to the appliance.
9.2 Cleaning the spray arms
Do not remove the spray arms.
If the holes in the spray arms are clogged,
remove remaining parts of soil with a thin
pointed object.
9.3 External cleaning
Clean the appliance with a moist soft
cloth.Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads
or solvents.
10. TROUBLESHOOTING
The appliance does not start or it stops
during operation.
Before you contact the Service, refer to
the information that follows for a solution
to the problem.With some problems, different indica-
tors flash continuously or intermit-
tently at the same time to show an
alarm code.
Alarm codeProblem
• The indicator of the set programme
flashes continuously.
• The end indicator flashes 1 time in-
termittently.The appliance does not fill with water.
• The indicator of the set programme
flashes continuously.
• The end indicator flashes 2 times in-
termittently.The appliance does not drain the water.
• The indicator of the set programme
flashes continuously.
• The end indicator flashes 3 times in-
termittently.The anti-flood device is on.
WARNING!
Deactivate the appliance before
you do the checks.
ENGLISH 13
 
						

							ProblemPossible solution
You cannot activate the appli-
ance.Make sure that the mains plug is connected
to the mains socket.
 Make sure that there is not a damaged fuse in
the fuse box.
The programme does not start.Make sure that the appliance door is closed.
 If the delay start is set, cancel the setting or
wait for the end of the countdown.
The appliance does not fill with
water.Make sure that the water tap is open.
 Make sure that the pressure of the water sup-
ply is not too low. For this information, con-
tact your local water authority.
 Make sure that the water tap is not clogged.
 Make sure that the filter in the inlet hose is not
clogged.
 Make sure that the inlet hose has no kinks or
bends.
The appliance does not drain the
water.Make sure that the sink spigot is not clogged.
 Make sure that the drain hose has no kinks or
bends.
The anti-flood device is on.Close the water tap and contact the Service.
After the checks are completed, activate
the appliance. The programme continues
from the point of interruption.
If the problem occurs again, contact the
Service.
If other alarm codes appear, contact the
Service.
10.1 If the washing and drying
results are not satisfactory
Whitish streaks or bluish layers on
glasses and dishes
• The released quantity of rinse aid is too
much. Adjust the rinse aid selector to a
lower position.
• The quantity of detergent is too much.
Stains and dry water drops on
glasses and dishes
• The released quantity of rinse aid is not
sufficient. Adjust the rinse aid selector
to a higher position.
• The quality of the detergent can be the
cause.Dishes are wet
• The programme is without a drying
phase or with a low temperature drying
phase.
• The rinse aid dispenser is empty.
• The quality of the rinse aid can be the
cause.
• The quality of the combi detergent tab-
lets can be the cause. Try a different
brand or activate the rinse aid dispens-
er and use rinse aid together with the
combi detergent tablets.
Refer to ‘HINTS AND TIPS’ for
other possible causes.
10.2 How to activate the rinse
aid dispenser
The activation of the rinse aid dispenser
can occur only with the multitab option
activated.
1.
Press the on/off button to activate the
appliance. Make sure that the appli-
14www.electrolux.com
 
						

							ance is in setting mode, refer to ‘Set-
ting and starting a programme.
2.Press and hold function buttons (B)
and (C) at the same time until the indi-
cators of function buttons (A), (B) and
(C) start to flash.
3.
Press function button (B).
• The indicators of function buttons
(A) and (C) go off.
• The indicator of function button (B)
continues to flash.• The end indicator is off.
4.
Press function button (B).
• The end indicator comes on. The
rinse aid dispenser is active.
5.
Deactivate the appliance to confirm
the setting.
6.
Adjust the released quantity of rinse
aid.
7.
Fill the rinse aid dispenser.
11. TECHNICAL INFORMATION
DimensionsWidth / Height / Depth (mm)596 / 818 - 898 / 550
Electrical connectionRefer to the rating plate.
 Voltage220-240 V
 Frequency50 Hz
Water supply pressureMin. / max. (bar / MPa)(0.5 / 0.05 ) / (8 / 0.8 )
Water supply 1)Cold water or hot water2)max. 60 °C
CapacityPlace settings12
Power consumptionLeft-on mode0.10 W
Off-mode0.10 W
1) 
Connect the water inlet hose to a water tap with a 3/4 thread.
2) 
If the hot water comes from alternative sources of energy, (e.g. solar panels, aeolian
energy), use the hot water supply to decrease energy consumption.
12. ENVIRONMENT CONCERNS
Recycle the materials with the symbol 
. Put the packaging in applicable
containers to recycle it.
Help protect the environment and human
health and to recycle waste of electricaland electronic appliances. Do not dispose
appliances marked with the symbol with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
ENGLISH 15
 
						

							www.electrolux.com/shop
117933341-A-422012