Electrolux Esl 46510 User Manual

							SETTING AND STARTING A WASHING PROGRAMME
Starting the washing programme
without delay start
1. Activate the appliance. Make sure that
the appliance is in setting mode.
2. Set the washing programme.
• The number related to the washing
programme flashes in the display.
3. If necessary, set the energy saver func-
tion.
4. Close the appliance door, the washing
programme starts automatically.
Starting the washing programme with
delay start
1. Activate the appliance.
2. Make sure that the appliance is in set-
ting mode.
3. Set the washing programme and, if nec-
essary, set the energy saver function .
4. Press the delay button again and again
until the display shows the time of the
delay start.
• The time of the delay start flashes in
the display.
• The delay indicator is on.
5. Close the appliance door, the count-
down starts automatically.
When the countdown is completed, the
washing programme starts automatically.
The opening of the appliance door in-
terrupts the countdown. When you
close the door, the countdown contin-
ues from the point of interruption.
Cancelling the delay start
If the appliance door is open, and the
countdown has not started
1. Press the delay button again and again
until the display shows the number of
the washing programme.
• The number flashes in the display.
2. Close the appliance door, the washing
programme starts automatically.
If the appliance door is closed, and the
countdown operates
1. Open the appliance door.
2. Press the delay button again and again
until the display shows the number of
the washing programme.• The number flashes for some sec-
onds and then the time of the wash-
ing programme shows in the display.
3. Close the appliance door, the washing
programme starts automatically.
Interruption of a washing programme
• Open the appliance door.
– The washing programme stops.
• Close the appliance door.
– The washing programme continues
from the point of interruption.
Cancelling the washing programme
If the washing programme has not started,
you can change the selection.
To change the selection while the washing
programme operates, it is necessary to
cancel the programme.
• Press the Reset button until the display
shows two horizontal status bars.
Make sure that there is detergent in the
detergent dispenser before you start a
new washing programme.
End of the washing programme
When the washing programme is comple-
ted, an intermittent acoustic signal sounds.
1. Open the appliance door.
• The end indicator is on
• The display shows a zero.
2. Deactivate the appliance.
3. For better drying results, keep the appli-
ance door ajar for some minutes.
Remove the items from the baskets
• Let the dishes become cold before you
remove them from the appliance. Hot
dishes can be easily damaged.
• First remove the items from the lower
basket, then from the upper basket.
• There can be water on the sides and on
the door of the appliance. Stainless steel
becomes cool more quickly than the
dishes.
electrolux 11
 
						

							WASHING PROGRAMMES
ProgrammeType of soilType of loadProgramme de-
scriptionEnergy
saver
function
1
 1)
AllCrockery, cutlery,
pots and pansPrewash
Wash 45 °C or 70 °C
Rinses
DryYes, with
effect
2Heavy soilCrockery, cutlery,
pots and pansPrewash
Wash 70 °C
Rinses
DryYes, with
effect
3
 2)
Fresh soilCrockery and cut-
leryWash 60 °C
RinseYes, with-
out effect
4
 3)
Normal soilCrockery and cut-
leryPrewash
Wash 50 °C
Rinses
DryYes, with
effect
5Normal or light soilDelicate crockery
and glasswareWash 45 °C
Rinses
DryYes, with
effect
1) The appliance senses the type of soil and the quantity of items in the baskets. It automatically adjusts the
temperature and quantity of the water, the energy consumption and the programme time.
2) With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
3) This is the standard programme for test institutes. With this programme you have the most efficient use of water
and energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test information.
Consumption values
ProgrammeProgramme time
(minute)Energy (kWh)Water (litre)
170 - 1300,7 - 1,38 - 16
2 
120 - 1301,1 - 1,212 - 13
3300,88
4160 - 1700,8 - 0,98 - 9
570 - 800,6 - 0,710 - 11
The water pressure and temperature,
the variations of the mains supply andthe quantity of dishes can change the
consumption values.
12 electrolux
 
						

							CARE AND CLEANING
To remove and clean the filters
Dirty filters decrease the washing results.
Although the maintenance is very low with
these filters, make a check at intervals and
if necessary, clean them.
1. Turn the filter (A) counterclockwise and
remove it out from filter (B).
A
B
2. Filter (A) has two parts. To disassemble
the filter, pull them apart.
3. Fully clean the parts with water.
4. Put the two parts of the filter (A) togeth-
er and push. Make sure that they en-
gage correctly in each other.
5. Remove the filter (B).
6. Fully clean the filter (B) with water.
7. Put the filter (B) to its initial position.
Make sure that it engages correctly in
the two guides (C).
C
8. Put the filter (A) into position in filter (B).
Turn the filter (A) clockwise until it locks.
To clean the spray arms
Do not remove the spray arms.
If the holes in the spray arms become clog-
ged, remove remaining parts of soil with a
thin pointed object.
To clean the external surfaces
Clean the external surfaces of the appliance
and control panel with a moist soft cloth.
Only use neutral detergents.
Do not use abrasive products, abrasive
cleaning pads or solvents (acetone).
WHAT TO DO IF…
The start of the appliance does not occur or
it stops during operation.
First try to find a solution to the problem (re-
fer to the table). If not, contact the service
centre.
With some malfunctions, the display
shows an alarm code:
•
 - The appliance does not fill with wa-
ter•
 - The appliance does not drain the
water
•
 - The anti-flood device is on.
Warning! Deactivate the appliance
before you do the checks.
electrolux 13
 
						

							MalfunctionPossible causePossible solution
The appliance does not fill with
water.The water tap is blocked or
there is limescale on it.Clean the water tap.
 The water pressure is too low.Contact your local water au-
thority.
 The water tap is closed.Open the water tap.
 The filter in the water inlet hose
is blocked.Clean the filter.
 The connection of the water in-
let hose is not correct.Make sure that the connection
is correct.
 The water inlet hose is dam-
aged.Make sure that the water inlet
hose has no damages.
The appliance does not drain
the water.There is a blockage in the sink
spigot.Clean the sink spigot.
 The connection of the water
drain hose is not correct.Make sure that the connection
is correct.
 The water drain hose is dam-
aged.Make sure that the water drain
hose has no damages.
The anti-flood device is on. Close the water tap and con-
tact the service centre.
The start of the washing pro-
gramme does not occur.The appliance door is open.Close the appliance door.
 The mains plug is not connec-
ted in the mains socket.Connect the mains plug.
 The fuse in the fuse box is
damaged.Replace the fuse.
 The delay start is set.• Cancel the delay start.
• When the countdown is
completed, the washing pro-
gramme starts automatically.
After the check, activate the appliance. The
programme continues from the point of in-
terruption.
If the malfunction occurs again, contact the
service centre.
If the display shows other alarm codes,
contact the service centre.
The necessary information for the service
centre is on the rating plate.Record this information:
–Model
(MOD.) ....................................................
....
– Product number
(PNC) ..........................................
– Serial number
(S.N.) ..............................................
The washing results and drying results are not satisfactory
ProblemPossible causePossible solution
The dishes are not clean.The washing programme was
not applicable for the type of
load and soil.Make sure that the washing
programme is applicable for the
type of load and soil.
 You did not put the items cor-
rectly in the baskets, water did
not touch all surfaces.Put the items correctly in the
baskets.
14 electrolux
 
						

							ProblemPossible causePossible solution
 The spray arms could not turn
freely. Incorrect position of the
items in the baskets.Make sure that an incorrect po-
sition of the items do not cause
the blockage of the spray arms.
 The filters are dirty or not as-
sembled and installed correctly.Make sure that the filters are
clean and correctly assembled
and installed.
 The quantity of detergent was
not sufficient or missing.Make sure that the quantity of
detergent is sufficient.
Limescale particles on the
dishes.The salt container is empty.Fill the salt container with dish-
washer salt.
 Incorrect level of the water soft-
ener adjustment.Adjust the water softener with
the correct level.
 The salt container cap is not
closed correctly.Make sure that the salt contain-
er cap is closed correctly.
There are streaks, whitish
stains, or a bluish layer on
glasses and dishes.The rinse aid quantity is too
high.Decrease the rinse aid quantity.
Dry water drop stains on
glasses and dishes.The rinse aid quantity is too
low.Increase the rinse aid quantity.
 The detergent can be the
cause.Use a different brand of deter-
gent.
The dishes are wet.The washing programme was
without a drying phase or with
a decreased drying phase.For better drying results, keep
the door ajar for some minutes.
The dishes are wet and matt.The rinse aid dispenser is emp-
ty.Fill the rinse aid dispenser with
rinse aid.
 The multitab function is on (this
function automatically deacti-
vates the rinse aid dispenser).Activate the rinse aid dispenser.
Activating the rinse aid dispenser
1. Activate the appliance.
2. Make sure that the appliance is in set-
ting mode.
3. Press and hold buttons (4) and (5) at the
same time until the indicators of buttons
(3), (4) and (5) flash.
4. Release buttons (4) and (5).
5. Press button (4).
• The indicators of buttons (3) and (5)
go off• The indicator of button (4) continues
to flash
• The display shows the setting of the
rinse aid dispenser.
Rinse aid dispenser
is off.
Rinse aid dispenser
is on.
6. Press button (4) to change the setting.
7. Deactivate the appliance to confirm.
TECHNICAL DATA
DimensionsWidth446 mm
 Height818 - 898 mm
 Depth550 mm
Water supply pressureMinimum0.5 bar (0.05 MPa)
 Maximum8 bar (0.8 MPa)
electrolux 15
 
						

							Water supply 1)Cold water or hot watermaximum 60 °C
CapacityPlace settings9
1) Connect the water inlet hose to a water tap with a 3/4 thread.
The rating plate on the inner edge of
the appliance door shows the electrical
connection data.
If the hot water comes from alternative
sources of energy, (e.g. solar panels,photovoltaic panels and aeolian), use a
hot water supply to decrease energy
consumption.
ENVIRONMENT CONCERNS
The symbol  on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will
help prevent potential negative
consequences for the environment and
human health, which could otherwise becaused by inappropriate waste handling of
this product. For more detailed information
about recycling of this product, please
contact your local council, your household
waste disposal service or the shop where
you purchased the product.
Recycle the materials with the symbol 
 .
Put the packaging in applicable containers
to recycle it.
16 electrolux
 
						

							electrolux 17
 
						

							18 electrolux
 
						

							electrolux 19
 
						

							117932350-A-102011
 www.electrolux.com/shop