Electrolux Esl 43010 User Manual

							5. Close the lid of the detergent dispenser.
Press the lid until it locks into position.
Different brands of detergent dissolve in
different times. Some detergent tablets
do not have the best cleaning results
during short washing programmes. Use
long washing programmes when you
use detergent tablets to fully remove the
detergent.
Use of combi detergent tablets
These tablets contain agents such as deter-
gent, rinse aid and dishwasher salt. Some
types of tablets can contain other agentsWhen you use tablets, that contain special
salt and rinse aid, it is not necessary to fill the
salt and rinse aid containers. In this condition
the rinse aid indicator light stays on when the
appliance is switched on.
1. Do a check if these tablets are applicable
for the local water hardness. Refer to the
instructions from the manufacturer.
2. Select the lowest setting for the water
hardness and rinse aid dosage.
Do these steps if the drying results are not
satisfactory
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
To use normal detergent again
1. Fill the salt container and rinse aid dis-
penser.
2. Adjust the water hardness setting to the
highest level.
3. Do a washing programme without
dishes.
4. Adjust the water softener to the water
hardness in your area.
5. Adjust the rinse aid dosage.
Setting and starting a washing programme
Important! Set the half-load option before
the start of a washing programme. You
cannot set the option when a washing
programme operates. If it is necessary to set
the half-load option, cancel the washing
programme.
Set the washing programme with the
door ajar. The washing programme only
starts after you close the door. Until then
it is possible to modify the settings.
Do these steps to set and start a washing
programme:
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press the programme selection/cancel
button again and again to set the washing
programme. Refer to the chapter Wash-
ing programmes.– The programme indicator light comes
on.
4. Close the door.
– The washing programme starts auto-
matically.When the washing programme oper-
ates, you cannot change the pro-
gramme. Cancel the washing pro-
gramme.
Warning! Only interrupt or cancel a
washing programme if necessary.
Caution! Open the door carefully. Hot
steam can come free.
Cancelling a washing programme
1. Press and hold the programme selection/
cancel button until:
– the programme indicator light goes off.
electrolux  11
 
						

							– The end-of-programme indicator light
starts to flash.
2. Release the programme selection/cancel
button to cancel the washing pro-
gramme.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with detergent
before you set a new washing programme.
Interrupting a washing programme
Open the door.
• The programme stops.
Close the door.
• The programme continues from the point
of interruption.
End of the washing programme
Switch off the appliance in these conditions:
• The appliance stops automatically.
• The audible signal for the end of the pro-
gramme operates.1. Open the door.
– The end-of-programme indicator light
comes on.
– The programme indicator light stays
on.
2. Press the on/off button.
3. For better drying results, keep the door
ajar for some minutes before you remove
the dishes.
Let the dishes cool down before you remove
them from the appliance. Hot dishes are
easily damaged.
Removing the load
• First remove items from the lower basket,
then from the upper basket.
• There can be water on the sides and door
of the appliance. Stainless steel becomes
cool more quickly than the dishes.
Washing programmes
Washing programmes
ProgrammeDegree of soilType of loadProgramme description
IntensiveHeavy soilCrockery, cutlery,
pots and pansPrewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
NormalNormal soilCrockery and cut-
leryPrewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
Quick1)Normal or light soilCrockery and cut-
leryMain wash up to 60°C
Final rinse
Economy 2)Normal soilCrockery and cut-
leryPrewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
PrewashAnyPartial load (to be
completed later in
the day).1 cold rinse (to prevent food scraps
to bond).
Detergent is not necessary with
this programme.
1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only
want to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes. Please refer to separate leaflet supplied, for test data. 12  electrolux
 
						

							Consumption values
ProgrammeDuration (in minutes)Energy (in kWh)Water (in litres)
Intensive110 - 1201,5 - 1,718 - 20
Normal100 - 1101,4 - 1,518 - 20
Quick300,88
Eco120 - 1300,8 - 0,912 - 13
Prewash110,15
The pressure and temperature of the
water, the variations of power supplyand the quantity of dishes can change
these values.
Care and cleaning
Warning! Switch the appliance off
before you clean the filters.
Cleaning the filters
Caution! Do not use the appliance
without the filters. Make sure that the
installation of the filters is correct.
Incorrect installation will cause
unsatisfactory washing results and
damage to the appliance.
If necessary, clean the filters. Dirty filters de-
crease the washing results.
The dishwasher has three filters:
1. coarse filter (A)
2. microfilter (B)
3. flat filter (C)
A
B
C
Do these steps to clean the filters:1. Open the door.
2. Remove the lower basket.
3. To unlock the filter system, turn the han-
dle on the microfilter (B) approximately
1/4 anticlockwise.
4. Remove the filter system.
5. Hold the coarse filter (A) by the handle
with the hole.
6. Remove the coarse filter (A) from the mi-
crofilter (B).
7. Remove the flat filter (C) from the bottom
of the appliance.
electrolux  13
 
						

							8. Clean the filters below running water.
9. Put the flat filter (C) in the bottom of the
appliance.
10. Put the coarse filter (A) in the microfilter
(B) and push the filters together.
11. Put the filter system in position.
12. To lock the filter system, turn the handle
on the microfilter (B) clockwise until it
lock in position.
13. Install the lower basket.
14. Close the door.
Do not remove the spray arms.
If the holes in the spray arms become clog-
ged, remove remaining parts of soil with a
cocktail stick.
External cleaning
Clean the external surfaces of the appliance
and control panel with a damp soft cloth.
Only use neutral detergents. Do not use
abrasive products, scouring pads or solvents
(acetone, trichloroethylene etc...).
Frost precautions
Caution! Do not install the appliance
where the temperature is below 0 °C.
The manufacturer is not responsible for
damage because of frost.
If not possible, empty the appliance and
close the door. Disconnect the water inlet
hose and remove water from the water inlet
hose.
What to do if…
The appliance does not start or stops during
operation.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a sol-
ution to the problem yourself, contact the
Service Force Centre.Caution! Switch off the appliance
before you do the below suggested
corrective actions.
Fault code and malfunctionPossible cause and solution
• continuous flash of the light of the
running programme
• intermittent audible signal
• 1 flash of the end-of-programme
indicator light
The dishwasher does not fill with wa-
ter• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the light of the
running programme
• intermittent audible signal
• 2 flashes of the end-of-pro-
gramme indicator light
The dishwasher will not drain• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The
hose can be kinked or squashed.
Make sure that the connection is correct.
The programme does not start• The appliance door is not closed.
Close the door.
• Mains plug is not connected in.
Put in the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
14  electrolux
 
						

							After the check, switch on the appliance. The
programme continues from the point of in-
terruption. If the malfunction shows again,
contact your Service Force Centre.
For other fault codes, not described in the
chart, contact your Service Force Centre.
These data are necessary to help you quickly
and correctly:• Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean• The selected washing programme is not applicable for the type of
load and soil.
• The baskets are loaded incorrectly so that water cannot reach all
surfaces.
• Spray arms do not turn freely because of incorrect arrangement of
the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
Limescales particles on the
dishes• The salt container is empty.
• The water softener is adjusted on a wrong level.
• The salt container cap is not closed correctly.
The dishes are wet and dull• No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky spots
or a bluish coating on glasses
and dishes• Decrease the rinse aid dosage.
Dry water drop signs on
glasses and dishes• Increase rinse aid dosage.
• The detergent can be the cause.
Technical data
DimensionsWidth cm59,6
 Height cm81,8 - 87,8
 Depth cm55
Electrical connection - Voltage -
Overall power - FuseInformation on the electrical connection is given on the rating plate
on the inner edge of the dishwasher door.
Water supply pressureMinimum0,5 bar (0,05 MPa)
 Maximum8 bar (0,8 MPa)
CapacityPlace settings9
Installation
Warning! Make sure that mains plug is
disconnected from the mains socket
during installation.
Important! Obey the instructions in the
enclosed template to:
• Build-in the appliance.
• Install the furniture panel.
• Connect to the water supply and drain.Install the appliance under a counter (kitchen
worktop or sink).
If a repair is necessary, the appliance must
be easily accessible for the engineer.
Put the appliance adjacent to a water tap and
a drain.
For the venting of the dishwasher only water
fill, water drain and power supply cable open-
ings are necessary.
electrolux  15
 
						

							The dishwasher has adjustable feet to allow
the adjustment of the height.
Make sure that the water inlet hose, the drain
hose and the supply cable are not kinked or
squashed, when you insert the machine.
Attaching the appliance to the adjacent
units
Make sure that the counter below which you
attach the appliance is a safe structure (ad-
jacent kitchen units, cabinets, wall).Adjusting the level of the appliance
Make sure that the appliance is level to close
and seal the door correctly. If the level of the
appliance is correct, the door does not catch
on the sides of the cabinet. If the door does
not close correctly, loosen or tighten the ad-
justable feet until the appliance is level.
Water connection
Water inlet hose
Connected the appliance to a hot (max. 60°)
or cold water supply.
If the hot water comes from alternative sour-
ces of energy that are more environmentally
friendly (e.g. solar or photovoltaic panels and
aeolian), use a hot water supply to decrease
energy consumption.
Connect the inlet hose to a water tap with an
external thread of 3/4”.
Caution! Do not use connection hoses
from an old appliance.
The water pressure must be in the limits (refer
to the chapter Technical data). Make sure
that the local water authority gives you the
average mains pressure in your area.
Make sure that there are no kinks in the water
inlet hose and that the water inlet hose is not
squashed or entangled.
Turn the inlet hose to the left or the right to
suit the installation. Fit the locknut correctly
to prevent water leaks.
Caution! Do not connect the appliance
to new pipes or pipes that are not used
for a long time. Let the water run for
some minutes, then connect the inlet
hose.
Water drain hose
1. Connect the water drain hose to the sink
spigot and attach it under the work sur-
face. This prevents that the waste water
from the sink goes back into the appli-
ance.
2. Connect the water drain hose to a stand
pipe with vent-hole (minimum internal di-
ameter 4 cm).
max 85 cm
min 40 cm
max 400 cm
Make sure that the drain hose is not bent or
squashed to prevent that the water drains
does not drain correctly.
Remove the sink plug when the appliance
drains the water to prevent that the water
goes back into the appliance.
A drain hose extension must not be longer
than 2 m. The internal diameter must not be
smaller than the diameter of the hose.
If you connect the water drain hose to a trap
spigot under the sink, remove the plastic
membrane (A). If you do not remove the
membrane, remaining food can cause a
blockage in the drain hose spigot
The appliance has a security feature to
prevent that dirty water goes back into
the appliance. If, the spigot of the sink
has a non-return valve, this valve can
cause the appliance to drain incorrectly.
Remove the non-return valve.
16  electrolux
 
						

							Caution! Make sure that the water
couplings are tight to prevent water
leakage.
Electrical connection
Warning! The manufacturer is not
responsible if you do not follow these
safety precautions.
Ground the appliance according to safe-
ty precautions.
Make sure that the rated voltage and
type of power on the rating plate agree
with the voltage and the power of the lo-
cal power supply.
Always use a correctly installed shock-
proof socket.
Do not use multi-way plugs, connectors
and extension cables. There is a risk of
fire.Do not replace the mains cable yourself.
Contact the Service Force Centre.
Make sure that the mains plug is acces-
sible after installation.
Do not pull the mains cable to discon-
nect the appliance. Always pull the
mains plug.
Warning! The appliance is supplied with
a 13 amp plug attached. Use a 13 amp
ASTA approved (BS 1362) fuse if it is
necessary to change the fuse in the plug
supplied.
Environment concerns
The symbol    on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
The packaging materials are environmentally
friendly and can be recycled. The plasticcomponents are identified by markings, e.g.
>PEPS
						

							18  electrolux
 
						

							electrolux  19
 
						

							117989531-01-062009
www.electrolux.com
To buy accessories, consumables and spare parts at our online shop please visit:
www.electrolux.co.uk
www.electrolux.ie