Eizo Flexscan Sx2262w Users Manual

							41Chapter 6  Reference
Dimensions Main unit566 mm (22.3 inch) × 456-538 mm (18.0 – 21.2 inch) × 230 mm  
(9.1 inch)
Main unit (without stand) 566 mm (22.3 inch) × 367 mm (14.4 inch) × 85 mm (3.4 inch)
Mass Main unit  Approx. 10.7 kg (23.6 lbs.)
Main unit (without stand)  Approx.7.1 kg (15.7 lbs.)
Movable range Tilt 40° Up, 0° Down
Swivel 35° Right, 35° Left
Adjustable height 82 mm (3.23 inch)
Rotation 90° (clockwise)
Environmental 
Conditions Temperature 
Operating temperature: 0 °C - 35 °C (32 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (- 4 °F - 140 °F)
Humidity Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
USB  Standard  USB Specification Revision 2.0
Port  Upstream port × 1, Downstream port × 2
Communication Speed  480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Supply current  Downstream: Max. 500mA /1 port
Main default settings (factory settings)
FineContrast User1
Power Save  On
Input Selection Manual
Screen Size Full
Auto EcoView On
Outline Enhancer 0
Menu Position Center
Eco Timer Off
Language  English
  
						

							42Chapter 6  Reference
Outside Dimensions
SX2262W
PIVOT
SWIVEL
355 (13.00)
36.2 (1.43)
172°
172°
53.8 (2.12)85 (3.35)
333 (13.01)
298.1 (11.07)
17.45 (0.69)
511 (20.01)17.6 (0.69)
521.5 (20.05)
17.45 (0.69)
φ220 (7.9)
90°
475.8 (18.07)
188.5 (7.04)
235.5 (9.03)
256 (10.01)
9.5 (0.37)
411.1 (16.02)
30°
324.1 (12.08)
181 (7.01)
240.5 (9.05)
347.5 (13.07)
235 (9.03)
100 (3.09)
100 (3.09)
205.5 (8.01) 205.5 (8.01)116.5 (4.06)
116.5 (4.06)
610.5 (24.00)
99.5 (3.92)
564.2 (22.02)
249 (9.08)
285 (11.02)
481.5 (18.00)
14.5 (0.57)
Unit: mm (inch)
SX2462W
90°
PIVOT
527(20.7)190(7.5)
35°315.8(12.4)
230(9.1)
399.5(15.7)35°
30.4(1.2)
15.5(0.61)
40°199.6(7.9)
281.4(11.1)
456～538\f(18
～21.2)
56.3
85
(2.22)
(3.35)
566(22.3)
520.4(20.5)
326(12.8) 367(14.4)
22.8(0.9)
22.8(0.9)
20.5(0.81)
20.5(0.81)
577.1(22.7)
287.5(11.3)
182.4(7.2)
8(0.31)
89(3.5)
272.5(10.7) 82
(3.23)
100(3.9)
133.5(5.3)
100(3.9) 233(9.2)
233(9.2)
133.5(5.3)
SWIVE\b
12～71.5\f(0.47
～2.81)
Unit: mm (inch)
  
						

							43Chapter 6  Reference
Connector Pin Assignment
• DVI-I connector
123
4
56
78
910 11 12
1314 15
16
19 20 21
17 18 22 23 24C1C2C3C4
C5
Pin 
No. Signal Pin 
No. Signal Pin 
No. Signal 
1 T.M.D.S. Data 2- 11 T.M.D.S. Data1/3 Shield  21 NC*
2 T.M.D.S. Data 2+  12 NC* 22 T.M.D.S. Clock shield
3 T.M.D.S. Data2/4 Shield  13 NC* 23 T.M.D.S. Clock+
4 NC* 14 +5V Power  24 T.M.D.S. Clock-
5 NC* 15 Ground (return for +5V, 
Hsync, and Vsync) C1 Analog Red
6 DDC Clock (SCL) 16 Hot Plug Detect C2 Analog Green
7 DDC Data (SDA)  17 T.M.D.S. Data0- C3 Analog Blue
8 Analog Vertical Sync  18 T.M.D.S. Data0+ C4 Analog Horizontal Sync
9 T.M.D.S. Data1-  19 T.M.D.S. Data0/5 Shield C5 Analog Ground(analog 
R,G,&B return)
10 T.M.D.S. Data1+ 20 NC*
 ( NC*: No Connection)
• DisplayPort connector
135791113151719
2468101214161820
Pin No.SignalPin No.SignalPin No.Signal
1 ML Lane3- 8 Ground15 AUX CH+
2 Ground 9 ML Lane1+16 Ground
3 ML Lane3+ 10 ML Lane0- 17 AUX CH-
4 ML Lane2- 11 Ground 18 Hot Plug Detect
5 Ground 12 ML Lane0+ 19 Return
6 ML Lane2+ 13 CONFIG1 20 DP PWR
7 ML Lane1- 14 CONFIG2
• USB port
Upstream
Series A connector
Series B connector Downstream
Contact No. 
Signal  Remarks
1 VCC Cable power
2 - Data Serial data
3 + Data Serial data
4 Ground Cable ground
  
						

							44Chapter 6  Reference
Accessories List
Cleaning Kit EIZO “ScreenCleaner”
Signal Cable PP200
Speaker Unit i•Sound L3
For the latest information about the accessories, refer to our web site. http://www.eizo.com
  
						

							45Chapter 6  Reference
6-6. Glossary
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the 
graphics system in use, when the analog input signal is converted to a digital signal for image display. 
This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the 
screen.
DDC/CI (Display Data Channel/Command Interface)
VESA provides the standardization for the interactive communication of the setting information, etc. 
between a PC and the monitor.
DisplayPort
VESA provides the digital interface standard for the digital display device. DisplayPort can transfer the 
video signal up to 16 bits for each channel of RGB, and the audio signal too. (This monitor supports the 
8-bit video signal only.)
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss. 
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. 
One is a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and 
analog signal inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and 
“Active Off (power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color 
by the light passing through the panel color filter. Red, green and blue are the three primary colors. All 
the colors on the screen are displayed by combining these three colors. The color tone can be changed by 
adjusting the light intensity (volume) passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma 
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value 
produces a highcontrast image.
  
						

							46Chapter 6  Reference
HDCP (High-bandwidth Digital Contents Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. 
This helps to transmit the digital contents safely by coding the digital contents sent via DVI terminal on 
the output side and decoding them on the input side. Any digital contents cannot be reproduced if both of 
the equipments on the output and input sides are not applicable to HDCP system.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment 
is made to adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted 
correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended 
that range adjustment be made before color adjustment.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This 
monitor consists of 1920 horizontal pixels and 1200 vertical pixels. At a resolution of 1920 x 1200, all 
pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for “color reproduction and color space” among peripheral devices (such as 
monitors, printers, digital cameras, scanners). sRGB allows Internet users to closely match colors as a 
simple color matching means for the Internet use.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. 
The screen becomes reddish at a low temperature, and bluish at a high temperature, like the flame 
temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management 
Signaling)
VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. 
DPMS defines the signal status between PC and monitor.
  
						

							47Chapter 6  Reference
6-7. Preset Timing
The following table shows factory preset video timing (for analog signal only).
Attention
• Display position may be deviated depending on the PC connected, which may require screen adjustment using Adjustment menu.
•
 
I
 f a signal other than those listed in the table is input, adjust the screen using the Adjustment menu. However, 
screen display may still be incorrect even after the adjustment.
•
 
W
 hen interlace signals are used, the screen cannot be displayed correctly even after screen adjustment using the 
Adjustment menu. 
Resolution Applicable 
signal Frequency
Polarity
Dot clock:  MHz Horizontal: 
kHz Vertical: 
Hz Horizontal Vertical
640 × 480 VGA
25.18 31.47 59.94 Negative Negative
720 × 400 VGA TEXT 28.32 31.47 70.09 Negative Positive
800 × 600 VESA 40.00 37.88 60.32 Positive Positive
1024 × 768 VESA 65.00 48.36 60.00 Negative Negative
1280 × 960 VESA 108.00 60.00 60.00 Positive Positive
1280 ×1024 VESA 108.00 63.98 60.02 Positive Positive
1600 ×1200 VESA 161.99 75.00 60.00 Positive Positive
1680 ×1050 VESA CVT 146.25 65.29 59.95 Negative Positive 1920 ×1200 VESA CVT RB 154.00 74.04 59.95 Positive Negative
  
						

							48 
Congratulations!
The display you have just purchased carries the TCO’03 Displays label. This 
means that your display is designed, manufactured and tested according to 
some of the strictest quality and environmental requirements in the world. 
This makes for a high performance product, designed with the user in focus 
that also minimizes the Impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
● Good visual er gonomics and image quality in order to improve the working environment for the user 
and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, 
reflectance, colour rendition and image stability.
Energy
● Energy-saving mode after a certain time - beneficial both for the user and environment
● Electrical safety
Emissions
● Electromagnetic fields
● Noise emissions
Ecology
● The products must be prepared  for recycling and the manufacturer must have a certified environmental 
management system such as EMAS or ISO 14000
● Restrictions on
● chlorinated and brominated flame retardants and polymers
● heavy metals such as cadmium, mercury and lead.
The requirements includes in this label have been developed by  TCO Development in co-operation with scientists, 
experts, users as well as manufacturers all over the world. Since the end of the 1980s  TCO has been involved in 
influencing the development of IT equipment in a more user-friendly direction. Our labeling system with displays 
in 1992 and is now requested by users and IT-manufacturers all over the world.
For more information, please visit www.tcodevelopment.com
TCO’03
Applicable	to	SX2262W	only.
  
						

							49 
For U.S.A. , Canada, etc. (rated 100-120 Vac) OnlyFCC Declaration of Conformity
We, the Responsible Party EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone:  (562) 431-5011
declare that the product Trade name:  EIZO
Model:  FlexScan SX2262W / SX2462W
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following 
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against 
harmful interference in a residential installation.  This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications.  However, there is no guarantee that interference will not occur in 
a particular installation. If this equipment does cause harmful interference to radio or television reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures.
*
 
R
 eorient or relocate the receiving antenna.
*
 
I
 ncrease the separation between the equipment and receiver.
*
 
C
 onnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
*
 
C
 onsult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the 
user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference 
within the limits of a Class B digital device.
-
 
A
 C Cord
-
 
S
 hielded Signal Cable (Enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
FCC Declaration of Conformity
  
						

							50 
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)
 
Der 
 Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät 
und  des  spezifizierten  Zubehörs  besitzen.  Das  Gewicht  des  Bildschirmgerätes  und  des  Zubehörs  sind  in  der 
zugehörenden Bedienungsanleitung angegeben.
b)
 
Die 
 Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher 
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)
 
Im 
 Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der 
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)
 
Der 
 Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach 
hinten ≥ 5°).
e)
 
Der 
 Standfuß  muß  die  Möglichkeit  zur  Drehung  des  Bildschirmgerätes  besitzen  (max.  ±180°).  Der  maximale 
Kraftaufwand dafür muß weniger als 100 N betragen.
f)
 
Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)

 
Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)

 
Der 
 Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position 
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1920 × 
1200, Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non interlaced.  Weiterhin wird aus 
ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte 
Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Hinweis zur Ergonomie