Eizo Flexscan P1700 Users Manual

English
1. INTRODUCTION11
Rear
(8) Power Connector
(9) D-Sub mini 15 pin Input Connector
(10) 4 Holes for Mounting an Arm-Stand*
4
(11) Security Lock Slot*5
(12) Stand
*4 The LCD monitor can be used with an optional arm stand by removing the stand, see 
page 22.
*5 Allows for connection of a security cable. This lock supports Kensington’s MicroSaver 
security system. 
For further information, please consult:
Kensington Technology Group 
2855 Campus Drive, San Mateo, CA 94403 USA
Tel: 800-650-4242, x3348...

English
122. CABLE CONNECTION
2. CABLE CONNECTION
2-1. Before Connecting
Before connecting your monitor to the PC, change the display screen settings 
(resolution (p. 30) and frequency) in accordance with the charts below.
NOTE
zWhen your computer and display support VESA DDC, the suitable resolution and 
the refresh rate are set by just plugging your display into the computer without 
any manual settings.
ResolutionFrequencyDot ClockRemarks
640×480 ~ 75 Hz
135 MHz (Max.)VGA, VESA
640×480 67 Hz Apple...

English
2. CABLE CONNECTION13
2-2. Connecting the Signal Cable
NOTE
zBe sure that the power switches of both the PC and the monitor are OFF.
1.Plug the signal cable into the connector at the rear of the monitor 
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Signal CableConnector of the PCPC
Signal Cable (enclosed) Video Output Connector / 
D-Sub mini 15 pinzStandard graphics card
zPower Macintosh G3 
(Blue & White)...

English
142. CABLE CONNECTION
2.Plug the power cord into the power connector on the rear of the 
monitor. Then, plug the other end of the cord into a power outlet. 
WARNING
Use the enclosed power cord and connect to the 
standard power outlet of your country.
Be sure to remain within the rated voltage of the power 
cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main 
outlet.
Not doing so may result in fire or electric shock. 
3.Turn on the monitor’s...

English
3. SCREENMANAGER15
3. SCREENMANAGER
3-1. How to use the ScreenManager
1.Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2.Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control buttons and press the 
Enter button. The sub menu appears.
(2) Use the Control buttons to select  the desired setting icon and  press the 
Enter button. The setting menu appears.
(3) Use the Control buttons to make a ll required...

English
163. SCREENMANAGER
3-2. ScreenManager Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
*1 Due to the inspection on the factory, the  usage time may not “0 hour” at shipping.
Main menuSub menuReference
Auto 
Adjustment 
Screen Screen 4-1. Auto Screen Adjustment (p. 19)
Range
Screen Clock Adjust the Clock  (p. 31). Phase Adjust the Phase  (p. 30).
Hor. Position Adjust the Horizontal Position. 
Ver. Position Adjust the Vertical Position.
Color...

English
3. SCREENMANAGER17
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
[To lock]
(1) Switch off the monitor’s Power by the power button.
(2) Press on the Enter button while switching on the monitor’s power.
[To unlock] 
(1) Switch off the monitor’s Power by the power button.
(2) Hold down the Enter button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state 
after...

English
184. ADJUSTMENT
4. ADJUSTMENT
4-1. Auto Screen Adjustment
Screen flickering is suppressed and the proper position is adjusted automatically in the 
following cases.
zWhen the monitor is input the input signal from the computer that has never been 
connected the monitor.
zChanging the monitor’s resolution or refresh rate
When the screen is flicking or the position is not proper.
[Procedure]
(1) Select   in the ScreenManager .
(2) Select  in the sub menu and press the Enter button. The message...

English
4. ADJUSTMENT19
4-3. Brightness Adjustment
BrightRegulator Function
BrightRegulator function adjusts the brightness of the screen automatically depending 
on the surrounding brightness. The brightness of backlight is adjusted as the sensor 
on the lower side of the monitor detects the surrounding brightness (Default: this 
function is set “Enable”.)
[To deactivate this function]
(1) Select  in the ScreenManager  menu.
(2) Select “Disable”.
NOTE
zDo not block the sensor  (p. 10) when using this...

English
204. ADJUSTMENT
4-4. Color Adjustment
The  menu in the ScreenManager enables to change the color of the screen.  
By using the , the adjustment mode can be selected from  (to adjust the color settings according to your preference) and   (p. 31) 
mode.
NOTE
zAllow the LCD monitor to stabilize for at least 20 minutes before making image 
adjustments. (Allow the monitor to warm up for at least 20 minutes before making 
adjustments.)
Adjustment Contents“ √ ”: Settable/Adjustable   “ – ”: Fixed at the...