Eizo Coloredge Cg232w Users Manual

5. Reference
31
5-4. Specifications
LCD PanelSize57 cm (22.5 inch)
Surface 
treatment Hard Coating
Surface 
hardness 2H
Response Time Approx. 12 ms
Viewing Angle Horizontal : 176°, Vertical : 176°
(CR: 10 or more)
Dot Pitch 0.252 mm
Horizontal Scan 
Frequenc\f Analog
26 - 92kHz
Digital 26 - 78kHz
Vertical Scan 
Frequenc\f Analog
23.8 - 86Hz
Digital 23.8 - 61Hz (VGA TEXT : 69 - 71Hz)
Resolution 1920 dots x 1200 li\lnes
Dot Clock 
(Max.) Analog
162MHz
Digital 162MHz
Displa\f Colors 1073.74 million...

32
5. Reference
Environment 
ConditionsTemperature Operating: 
Transportation/Storage: 0°C ~ 35°C (32°F ~\l 95°F) 
-20°C ~ 60°C (-4°F\l ~ 140°F)
Humidit\f Operating:  Transportation/Storage: 30% to 80% R.H. Non-condensing 
30% to 80% R.H. Non-condensing
Pressure Operating:  Transportation/Storage: 700 to 1060 hPa. 
200 to 1060 hPa. 
USB standard USB Specification 
Revision 2.0
USB port Upstream port x 1 
Downstream port x 2
Communication 
Speed480 Mbps (high), 1\l2 Mbps (full), 1.5 M\lbps (low)
Power...

5. Reference
33
Dimensions
100(3.9)
172.5(6.8)
233.5(9.2)233.5(9.2)
100(3.9)
144.5(5.7)
144.5(5.7)
255(10)
TILT 40°
311(12.2)
113(4.4)  64
(2.52)486.5(19.2)
406(16)
567(22.3)
304.5(12)389(15.3)
286.5～404.5(11.3～15.9)
481～599(18.9～23.6)
92(3.62)
323(12.7)
500(19.7)
S\fIEVEL
35°35°
240(9.4)
unit: mm (inch)
  

34
5. Reference
Pin Assi\fnment
•DVI-D Connector
123
4
56
78
910 11 12
1314 15
16
19 20 21
17 18 22 23 24
Pin No.Si\fnalPin No.Si\fnalPin No.Si\fnal
1 T.M.D.S. Data 2- 9 T.M.D.S. Data1- 17 T.M.D.S. Data0-
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+
3 T.M.D.S. Data2/4 Shield 11 T.M.D.S. Data1/3 Shield 19 T.M.D.S. Data0/5 Shield
4 NC* 12 NC* 20 NC*
5 NC* 13 NC* 21 NC*
6 DDC Clock  (SCL) 14 +5V Power 22 T.M.D.S. Clock shield
7 DDC Data  (SDA) 15 Ground  (return for +5V, 
Hs\fnc, and Vs\fnc) 23...

5. Reference
35
5-5. Glossar\b
Clock
With  the  analog  input  signal  displa\f,  the  analog  signal  is  converted  to  a  digital  signal  b\f  the  LCD 
circuitr\f. To  convert  the  signal  correctl\f,  the  LCD  monitor  needs  to  produce  the  same  number  clock 
pulse as the dot clock of the graphics s\fstem. When the clock pulse is not correctl\f set, some verti-
cal bars of distortion are displa\fed on the screen.
DVI (Di\fital Visual Interface)
A  digital  flat  panel  interface.  DV\b  can...

36
5. Reference
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to form the screen 
image. The  displa\f  panel  of  this  monitor  consists  of  1920  horizontal  pixels  and  1200  vertical  pixels. 
At a resolution of \l1920 x 1200 , imag\les are displa\fed as a full screen\l(1:1).
SDI (Serial Di\fital \aInterface)
One of the interfaces standardized b\f the SMPTE and AR\bB. \bt transmits image signals, s\fnc signal, 
clock, and audio signa\lls all on one...

6. Preset Timing
37
6. Preset Timin\f
The following table shows factor\f preset video timi\lng (for analog signal on\ll\f).
Note
•
 Displa

\f position ma\f be deviated depending o\ln the PC connected\l, which ma\f require screen 
adjustment using A\ldjustment menu.
•
 \bf a signal other t\lhan those listed in\l the tab

le is input, adjust\l the screen using \lthe Adjustment men\lu. 
However, screen displa\f ma\f still be incorrect\l even after the adjus\ltment.
•
 When inter

lace signals are us\led,...

38
For U.S.A, Canada, etc.  (rated 100-120 Vac) Only
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of 
the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment.  This equipment generates, uses, and can radiate radio frequency 
energy and if not installed and used in accordance with the instruction manual, may cause harmful...

39
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)
 
Der 
 Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes...

4th Edition-March, 2012
03V22517D1(U.M-CG232W)Copyright © 2008-2012 EIZO NANAO CORPORATION All rights reserved.