Eizo Coloredge Cg222w Users Manual

							
3. Screen Adjustment and Settings
1

-. Power Indicator Setting
Light	off	the	power	indicator.	This	function	is	available	for	the	multiple	panels	settings.
[Procedure]
1.	Select		in	the	Adjustment	menu		menu.
2.	Select	"Disable".
-. Automatic brightness adjustment
The	sensor	on	the	front	side	of	the	monitor	detects	the	environmental	brightness	to	adjust	the	screen	
brightness	automatically	and	comfortably.
[Procedure]
1.	Select		in	the	Adjustment	menu		menu.
2.	Select	"Enable".
Note
•	This	function	is	not	available	in	the	EMU	and	CAL	modes.
Downloaded	from	ManualMonitor.com	Manuals 
						

							

3. Screen Adjustment and Settings

-. Displaying Lower Resolutions
The	lower	resolutions	are	enlarged	to	full	screen	automatically.	Using	the		function	in	the	
	menu	enables	to	change	the	screen	size.
1	 Enlarge	the	screen	size	when	displaying	a	low	resolution.
		Select	the	.	
Select	the		in	the		menu	and	select	the	screen	size	by	using	
	and	.
ModeFunction
FullDisplays the picture on the screen in full, irrespective of the picture's resolution. 
Since the verticalresolution and the horizontal resolution are enlarged at different 
rates, some images may appeardistorted.
EnlargedDisplays the picture on the screen in full, irrespective of the picture's resolution. 
Since the vertical resolution and horizontal resolution are enlarged at same rates, 
some horizontal or vertical image maydisappear.
NormalDisplays the picture at the actual Screen resolution.
	
Example:	Displaying	1280	x	1024
2	 Smooth	the	blurred	texts	of	the	enlarged	screen.
	Switch	the	< Smoothing>	setting.
When	a	low-resolution	image	is	displayed	in	the	
"Full" 	or	"Enlarged"	mode,	the	characters	or	
lines	of	the	displayed	image	may	be	blurred.
Select	the	suitable	level	from	1	-	5	(Soft	-	Sharp).
	
Select		in	the		menu	and	adjust	by	using	the	right	and	left	switches.
Note
• 	Smoothing	setting	may	not	be	required	depending	on	the	display	resolution.	(You	cannot	choose	
the	smoothing	icon.)
(1680 × 1050)(1312 × 1050)(1280 × 1024)
Full (Default Setting)EnlargedNormal
 
						

							
3. Screen Adjustment and Settings


3	 Set	the	brightness	of	the	black	area	surrounding	the	displayed	image.
	Set	the	.
In	the	"Enlarge"	mode	or	"Full	Screen"	mode,	the	outer	area	(border)	is	usually	black.	Select	
	in	the		menu	and	adjust	by	using	
.
-10. Setting the orientation of the Adjustment menu
The	orientation	of	the	Adjustment	menu	can	be	changed.
[Procedure]
1.	Select		in	the	Adjustment	menu		menu.
2.	Select		in	the		menu.
3.	Use	
	to	select	between	"Portrait"	and	"Landscape".
4.	Turn	the	monitor	screen	90°	in	clockwise	direction.
Tips
• 	If	you	use	the	monitor	with	"Portrait"	position,	the	setting	may	be	required	to	change	depending	on	
the	graphics	board	used	in	your	PC.	Refer	to	the	manual	of	the	graphics	board	for	details.
-11. EIZO Logo Appearing Function
When	switching	on	the	power	button	on	the	front	control	panel,	the	EIZO	logo	is	displayed	for	a	while.	
If	you	desire	to	display	or	undisplay	this	logo,	use	this	function.	(Default	is	logo	appearing.)
[To undisplay]
1.	Press		to	turn	off	the	unit.
2.	Press	
	again	while	pressing	.		
The	EIZO	logo	does	not	appear	on	the	screen.
[To display]
1.	Press		to	turn	off	the	unit.
2.	Press	
	again	while	pressing	.		
The	EIZO	logo	appear	on	the	screen.
Border
 
						

							

4. Troubleshooting

.Troubleshooting
If	a	problem	still	remains	after	applying	the	suggested	remedies,	contact	your	local	dealer.
•	No-picture	problems	:	See	No.1	-	No.2
•	Imaging	problems	:	See	No.3	-	No.14
•	Other	problems	:	See	No.15	-	No.18
•	USB	problems	:	See	No.19	
ProblemsPossible cause and remedy
1.  No picture
•
 Power indicator does not light.
•
 Check whether the power cord is connected correctly. If 
the problem persists, turn off the monitor, and then turn 
it on again a few minutes later.
•
 Press .
•
 Power indicator is lighting blue.•
 Set each RGB adjusting value in  to higher level. 
(page 18).
•
 Power indicator is lighting orange.•
 Switch the input signal with .
•
 Operate the mouse or keyboard.
•
 Turn on the PC. 
2.  The message below appears.
This message appears when the signal is not input 
correctly even when the monitor functions properly.
•
 This message appears when no signal is input. 
(This is displayed for about 40 seconds)
•
 The message shown left may appear, because some 
PCs do not output the signal soon after power-on.
•
 Check whether the PC is turned on.
•
 Check whether the signal cable is connected properly. 
•
 Switch the input signal with .
•
 The message below shows that the input signal is out of 
the specified frequency range. (Such signal frequency is 
displayed in red.)
	 Example:
•
 Check whether the signal setting of your PC matches 
the resolution and the vertical frequency settings for the 
monitor. (See “Compatible Resolutions/Frequencies” on 
the cover back of the Setup Manual.)
•
 Reboot the PC.
•
 Select an appropriate display mode using the graphics 
board’s utility. Refer to the manual of the graphics board 
for details.
fD:  Dot Clock 
 
(Displayed only when the digital signal inputs)
fH:  Horizontal Frequency
fV:  Vertical Frequency
3.  Display position is incorrect.
•
 Adjust image position so that it is displayed properly 
within the display area using the  adjustment 
(page 15).
•
 If the problem persists, use the graphics board’s utility if 
available to change the display position.
4.  Screen image displayed is smaller or larger than the 
actual screen image.
•
 Adjust the resolution using  so that the 
input signal resolution equals the resolution in the 
resolution adjustment menu (page 15).
 
						

							
4. Troubleshooting


ProblemsPossible cause and remedy
5. Vertical bars appear on the screen or a part of the image 
is flickering.
•
 Adjust using  (page 14).
6.  The characters and images have several vertical bars on 
their right side.
•
 Adjust the characters and images using the  
.
7.  Whole screen is flickering or blurring.
•
 Adjust using  (page 14).
8.  Characters are blurred.
•
 Adjust using  (page 22).
9.  Upper part of the screen is distorted as shown below. 
•
 This is caused when both composite sync (X-OR) 
signal and separate vertical sync signal are input 
simultaneously. Select either composite signal or 
separate signal
10.The screen is too bright or too dark.•
 Adjust . (The LCD monitor backlight has a 
fixed life span. When the screen becomes dark or begins 
to flicker, contact your local dealer.)
11.Afterimages appear.•
 Use a screen saver or off timer function for a long-time 
image display.
•
 Afterimages are particular to LCD monitors. Avoid 
displaying the same image for a long time.
12.Green/red/blue/white dots or defective dots remain on 
the screen.
•
 This is due to LCD panel characteristics and is not a 
failure.
13.Interference patterns or fingerprints remain on the 
screen.
•
 Leave the monitor with a white screen or a black screen. 
The symptom may disappear.
14.Noise appears on the screen.•
 When entering the signals of analog input, select 1 to 
4 in  from the  menu to change 
the mode.
•
 When entering the signals of HDCP system, the normal 
images may not be displayed immediately.
15.The  icon on the Adjustment menu 
 cannot be selected.
•
 Smoothing setting may not be required depending 
on the display resolution. (You cannot choose the 
smoothing icon.)
•
  is disabled when the screen is displayed 
in the following resolutions.
•
 1680 × 1050 
•
 Select [Normal] during .
16.The Main menu of Adjustment menu does not start.•
 Check for Adjustment Lock function (page 20).
17.The FineContrast mode is not displayed.•
 Check for Adjustment Lock function (page 20).
 
						

							

4. Troubleshooting

ProblemsPossible cause and remedy
18.	does not function.•  (Auto Adjustment function) does not function when 
digital signal is input. 
• Check for Adjustment Lock function (page 20).
•
 This function does not work correctly with some graphics 
boards.
19.The monitor connected with the USB cable is not 
detected. / USB devices connected to the monitor does 
not work.
•
 Check that the USB cable is correctly connected.
•
 Check the downstream ports by connecting the 
peripherals to other downstream ports. If the problem is 
solved by doing this, contact an EIZO dealer. (For details, 
refer to the manual of the PC.)
•
 Try executing the following method.
•Restarting the PC
•Connecting the PC and peripherals directly
If the problem is solved by doing this, contact an EIZO 
dealer.
•
 Check that the USB cable is correctly connected.
•
 Check that the PC and OS are USB compliant. (For 
verification of USB support, consult the manufacturer of 
each system.)
•
 Check the PC's BIOS setting for USB when using 
windows. (For details, refer to the manual of the PC.)
 
						

							
5. Reference


. Reference
-1. Attaching an arm
The	LCD	monitor	can	be	used	with	an	arm	by	removing	the	tilt	stand	and	attaching	the	arm	stand	to	the	
LCD	monitor.
Note
•	If	you	will	use	the	arm	or	stand	of	other	manufacturers,	confirm	the	followings	to	the	manufacturers	
before	selecting.
- 	Hole	spacing	on	the	arm	mounting	
100	mm	x	100	mm	(VESA	compliant)	
- 	Supportable	Weight:	Total	weight	of	the	monitor	(without	stand)	and	attaching	equipment	such	
as	a	cable
- 	TÜV/GS	approved	arm	or	stand
• 	Please	connect	cables	after	attaching	an	arm	stand.
Setup Procedure
1	 Lay	the	LCD	monitor	down.	Do	not	scratch	the	panel.
2	 Remove	the	tilt	stand	by	loosening	the	screws.
Unscrew	the	four	screws	securing	the	unit	and	the	satand	with	the	screwdriver.
3	 Attach	an	arm	stand	to	the	LCD	monitor	securely.
Secure	the	monitor	to	the	arm	or	stand	using	the	screws	specified	in	the	user's	manual	of	the	arm	
or	stand.
Downloaded	from	ManualMonitor.com	Manuals 
						

							

5. Reference

-. Specifications
LCD Panel56 cm (22.0 inch), TFT color LCD panel  Surface treatment : Hard Coating Surface hardness : 3H Response Time : 16ms
Viewing AngleHorizontal : 178°, Vertical : 178°(CR: 10 or more)
Dot Pitch0.282mm
Horizontal Scan 
Frequency
Analog24~82 kHz (Automatic)
Digital31~65 kHz
Vertical Scan 
Frequency
Analog47.5~86Hz (Automatic)   (1280x1024 : 47.5 ~ 76Hz)                                         (1680x1050 : 47.5 ~ 61Hz)
Digital47.5 ~ 61 Hz (VGA TEXT: 69 ~ 71 Hz)
Resolution1680 dots x 1050 lines
Dot Clock 
(Max.)
Analog150 MHz
Digital120 MHz
Display Colors16.77 million colors (max.)
Recommended Brightness80cd/m2 or less  (with color temperature of between 5000K to 6500K)
Display Area473.8 mm (H) × 296.1 mm (V) (18.7" (H) x 11.7" (V))
Power Supply100-120/200-240 VAC±10%, 50/60 Hz, 0.75 A/0.4 A 
Power ConsumptionMax.: Min. (Normal): Power Saving Mode: Power Button off:
75 W (with USB load) 65 W (without USB load) 2W or less (for single signal input without USB load) 1W or less (without USB load)
Input Signal ConnectorDVI-I connector (Applicable to HDCP)×2
Analog Input Signal (Sync)Separate, TTL, Positive/Negative
Composite, TTL, Positive/Negative
Analog Input Signal (Video)0.7 Vp-p / 75 ohms, Positive
Input Signal (Digital)TMDS (Single Link)
Signal 
registration
Analog45 (Factory preset: 24)
Digital10 (Factory preset: 0)
Plug & PlayVESA DDC 2B / EDID structure 1.3
Dimensionswith stand507 mm (W) x 439 ~ 521 mm (H) x 230 mm (D) (20"(W) x 17.3" ~ 20.5" (H) x 9.1"(D))
without stand507 mm (W) x 333 mm (H) x 74 mm (D) (20"(W) x 13.1" (H) x 2.9"(D))
with hood513 mm (W) x 445 ~ 527 mm (H) x 340 mm (D) (20.2"(W) x 17.5" ~ 20.7" (H) x 13.4"(D))
Weightwith stand11.2 kg (24.7 lbs.)
without stand7.7 kg (17 lbs.)
with hood12 kg (26.5 lbs.)
Environment 
Conditions
TemperatureOperating: Storage:0°C ~ 35°C (32°F ~ 95°F) -20°C ~ 60°C (-4°F ~ 140°F)
HumidityOperating: Storage:30% to 80% R.H. Non-condensing 30% to 80% R.H. Non-condensing
PressureOperating: Storage:700 to 1060 hPa. 200 to 1060 hPa. 
USBstandardUSB Specification Revision 2.0
USB portUpstream port x 1 Downstream port x 2
Communication 
Speed
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Power SupplyDownstream: 500 mA for each (max.)
 
						

							
5. Reference


Default settings
Brightness33%
Smoothing3
Temperature5000K
FineContrast ModeCustom
PowerManager Analog input : VESA DPMS 
Digital input:DVI DMPM
Screen SizeFull
Input Priority1
Off TimerDisable
Menu SettingsMenu SizeNormal
Menu Off Timer45 sec
BrightRegulatorDisable
BeepOn
LanguageEnglish
Beeper settings
Short beepAdjustment menu item selsected. Adjustment menu parameter adjusted to minimum or maximum limit. 
 pressed 
When locked or unlocked with 
Long beep pressed Adjustment menu data-save executed.
4 short beepsMonitor not connected correctly.
PC turned off.
Monitor received unsupported signal frequency.
2 short beeps every 15 sec.Monitor is in the advance notice mode of the Off Timer.
The power will be off within fifteen minutes.
 
						

							
0
5. Reference

Dimensions
333(13.1)298.1(11.7)
475.8(18.7)507(20.0)
35°35°
203.5(8.0)100(3.9)203.5(8.0)
222.5
100
116.5
43.974(2.91)
106(4.2)
TILT 40°253.5(10.0)
190(7.5)
230(9.1)398.5(15.7)
521439～
20.5)
(17.3～
10119～4.0)
(0.75～
(1.73)
4*(/-4*(/-
SWIVEL
513(20.2)229(9)340(13.4)
445(17.5)
339(13.3)
3(0.12)
355(14)
16(0.63)
172.5(6.8)
45.6(1.8)
151(5.9)
uinit: mm (inch)