Home > Eiki > Projector > Eiki Projector LC-XNS2600 User Manual

Eiki Projector LC-XNS2600 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Eiki Projector LC-XNS2600 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 422 Eiki manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							61
    Indicator and projector state
    Check the indicator to know about the state of projector.
    *  When the lamp reaches the end of its life, the WARNING indicator lights red.  
    In this case, replace the lamp with a new one promptly.
    ....Green....Red....Orange....Of f
    ....Green flashes....Red flashes....Orange flashes?
    ?
    Indicator
    State of projector
    POWER
    (Green/Red) WARNING
    (Red)
    The projector is off. (AC power cord not connected).
    The projector is operating normally.
    - In standby mode. Press POWER to power on the projector.
    - When the projector is cool enough, the temperature is restored   
      to the normal value, you can turn on the projector. And the 
      POWER indicator  stops flashing.
    Internal temperature too high and can’t be turned on. When 
    the projector is cool enough, the temperature is restored to the 
    normal value and the POWER indicator lights red, you can turn 
    on the projector .
    In power management mode.
    Ready for standby mode or the lamp is being cooled. Before you 
    turn on the projector, you should wait till the lamp is cool enough 
    and the POWER indicator flashes.
    Can’t be turned on because error is detected. You should unplug 
    the power cord. Then insert it again and power on the projector. 
    If the projector is powered off again, you should cut off the power 
    and contact the local distributor or repair center. In this case, 
    stop  operate  the  projector.  Other wise,  electric  shock  or  fire  may 
    o c c u r.
              ―The service life of the lamp is over. You should replace it with a 
    new one in time.*
    Appendix  
    						
    							62
    Compatible computer specifications
    This projector can receive the signals below:
    Appendix
    √  Note:
       The specification is subject to change without any prior notice. 
    Signal formatResolutionScanning frequencyDot Frequceny
    (Mhz)Signal horizontal 
    frequency (Khz) Field 
    Frequceny (Hz)RGB Component HDMIVideo/S-Video
    NTSC/NTSC443/PAL-M (720x487)15.73459.940 - o
    PAL/PAL-N/SECAM (720x576)15.62550.000 - o
    525i (480i) 720x480i
    15.73459.940 13.500 o
    720(1440)x480i 15.73459.940 27.000 o
    625i (576i) 720x576i
    15.62550.000 13.500 o
    720(1440)x576i 15.62550.000 27.000 o
    525p (480p) 720x48331.46959.940 27.000 oo
    625p (576p) 720x57631.25050.000 27.000 oo
    750 (720)/60p 1280x72045.000
    60.000 74.250 oo
    44.955 59.940 74.176
    750 (720)/50p 1280x72037.50050.000 74.250 oo
    1125 (1080)/60i  1920x1080i33.750
    60.000 74.250 oo
    33.716 59.940 74.176
    1125 (1080)/50i 1920x1080i28.12550.000 74.250 oo
    1125 (1080)/24p 1920x108027.000
    24.000 74.250 o
    26.973 23.976 74.176
    1125 (1080)/25p 1920x108028.12525.000 74.250
    1125 (1080)/30p 1920x108033.750
    30.000 74.250
    33.716 29.970 74.176
    1125 (1080)/60p 1920x108067.500
    60.000 148.500 o
    67.433 59.940 148.352
    1125 (1080)/50p 1920x108056.25050.000 148.500 o
    VGA 640x48031.469
    59.940 25.175 o o
    35.000 66.667 30.240 o o
    37.861 72.809 31.500 o o
    37.500 75.000 31.500 o o
    43.269 85.008 36.000 o o
    SVGA 800x60035.156
    56.250 36.000 o o
    37.879 60.317 40.000 o o
    48.077 72.188 50.000 o o
    46.875 75.000 49.500 o o
    53.674 85.061 56.250 o o
    MAC16 832x62449.72574.550 57.283 o o
    XGA 1024x76848.363
    60.004 65.000 o o
    56.476 70.069 75.000 o o
    60.023 75.029 78.750 o o
    68.678 84.997 94.500 o o
    MXGA 1152x86463.99570.020 94.200 o o
    1280x768 1280x76847.776
    59.870 79.500 o o
    60.290 74.890 102.250 o o
    68.630 84.840 117.500 o o
    1280x800 1280x80049.702
    59.810 83.500 o o
    62.795 74.934 106.500 o o
    71.554 84.880 122.500 o o
    MSXGA 1280x96060.00060.000 108.000 o o
    SXGA 1280x102463.981
    60.020 108.000 o o
    76.968 71.932 133.000 o o
    79.977 75.025 135.001 o o
    91.150 85.020 157.500 o o
    1366x768 1366x76847.72059.799 84.750 o o
    SXGA+ 1400x105065.31759.978 121.750 o o
    UXGA 1600x120075.00060.000 162.000 o o
    WSXGA+ 1680x105065.29059.954 146.250 o o
    WUXGA 1920x120074.03859.950 154.000 0 0  
    						
    							63
    Technical Specifications
                      Model
    ParameterLC-XNS2600
    LC-XNS3100LC-WNS3200
    Adjustbale foot 10˚
    LCD system 0.63" TFT , active matrix, 3-panel 0.59" TFT , active matrix, 3-panel
    Resolution XGA (1024x768)WXGA (1280x800)
    Contrast 2400:1
    Lens F=2.1-2.25, f=19.109-22.936,
    1.2 optical zooming,1/4-16 digital zooming F=1.58-1.75,f=18.85-22.63,
    1.2 optical zooming,1/4-16 digital zooming
    Project distance 0.88m~10.83m (4:3)  0.96m~11.80m (16:9) 0.94m~11.48m(16:10)
    Image size 
    (diagonal lines)30"~300"
    Aspect ratio 4:3 (Standard)
    16:9 (Compatible) 16:10 (Standard)
     
     4:3 (Compatible)
    Lamp comsuption 230w
    InputVGAx2;
    YCbCrx1;
    Videox1(Complex with YCbCr); S-videox1;
    Audio in(3.5mm)x1; HDMIx1;
    RCAx2(L/R)
    Output VGAx1(Complex with VGA in2);
    Audio out(3.5mm)x1
    Control port RS232 in;RJ45;
    Horizontal 
    scanning frequecy 15~100KHz 
    Verticalscanning 
    frequecy 48~85Hz
    Compatible 
    Computer signal VGA, SVGA, XGA, SXGA,WXGA,
    UXGA,Mac
    Compatible Video 
    signal PAL,SECAM,NTSC 4.43,PAL-M, PAL-N, 480i,480p,576i,576p,720p,1035i,1080i
    Power supply 100~240V, 50/60Hz
    Operation 
    temperature 5
    ℃ ~40
    ℃(35
    ℃  to eco mode)
    Storage 
    temperature -10
    ℃~60
    ℃
    High land at most 2000m high
    Speaker 7Wx1
    Dimensions (W×H×D ) 340.0mmx86.8mmx242.0mm  (not including the adjustable foot)
    Net Weight 3.05Kg
    Appendix
    ● The aforesaid specification is subject to change without prior notice.
    ● Liquid cr ystal panel is made on the basis of high standard, where 99.99% of the pixels are effective. 
       Due to the nature of the liquid cr ystal panel, a fraction of the pixels (0.01% or less) may be ineffective.  
    						
    							64
    Content of hazardous substances and elements
    Configurations of terminals
    COMPUTER IN 1/SCART, COMPUTER IN 2/MONITIOR OUTTerminal: Analog  RGB (D-sub 15 pin)
    512341096781514131112
    1 Red (Input/output) 9-----
    2 Green (Input/output) 10Grounding (field synchronizing)
    3 Blue (Input/output) 11Grounding
    4 ----- 12DDC data
    5 Grounding (line synchronizing) 13Horizontal synchronizing 
    (compound sync.) input/output
    6 Grounding (red) 14Vertical synchronizing input/
    output
    7 Grounding (green) 15DDC Clock
    8 Grounding (blue)
    1TMDS Data2+ 11TMDS Clock Shield 
    2 TMDS Data2 Shield  12TMDS Clock– 
    3 TMDS Data2–  13CEC 
    4 TMDS Data1+  14Reser ved (N.C. on device) 
    5 TMDS Data1 Shield  15SCL 
    6 TMDS Data1–  16SDA 
    7 TMDS Data0+  17DDC/CEC Ground 
    8 TMDS Data0 Shield  18+5V Power 
    9 TMDS Data0 –  19Hot Plug Detect 
    10 TMDS Clock+ 
    1-----
    2 RXD
    3 TXD
    4 -----
    5 GND
    6 -----
    7 -----
    8 -----
    9 -----1TX + 5-----
    2 TX - 6-----
    3 ----- 7R X +
    4 ----- 8R X -
    CONTROL terminal (D-SUB-9 pin)
    HDMI terminal (HDMI Type A 19 pin) LAN terminal
    1
    2
    4
    6
    8
    9
    75 3
    10
    12
    14
    16
    18
    19
    17 1513 11
    87 65 432 1
    Appendix
    Name of parts Hazardous substances and elements
    Pb Hg CdCr6+ PBBPBDE
    Optical parts
    *1 ○ ○ ○ ○ ○
    Electric parts*2
    ○ ○ ○ ○ ○
    Cabinet, mechanical parts
    ○ ○ ○ ○ ○
    Lamp unit
    ○ ○ ○ ○
    Batteries○○ ○ ○ ○ ○Others(Remote control, 
    cable and other parts)
    ○ ○ ○ ○ ○
    ○: It means that contents of hazardous substances in all homogeneous materials in this part don’t
        exceed “Required Limitations” specified in SJ/ T11363 -2006.
    ×: It means that contents of hazardous substances in at least one homogeneous material in this part
        exceed “Required Limitations” specified in SJ/ T11363 -2006.
    Note:
    *1 :Optical parts includes optical lens, monitor, reflection lens ect.*2 :Electric parts includes PCB, internal wires, fans, power supply, sensors etc.  
    						
    							65
    Appendix
    Unit: mm
    Screw Holes for Ceiling Mount
    Screw: M4
    Depth: 10.0
    Dimensions  
    						
    							66
    PIN code memorandum
    Appendix
    Write down the PIN code in the blank below and keep it, please contact the repair center.
    PIN code lock
    Locking startup-animation PIN code Factory default PIN code 111*
    Factory default PIN code 111*
    *If this 3 -digit number is changed,
    the factory default number will be ineffective.  
    						
    							U.S.A.
    EIKI International, Inc.
    30251 Esperanza
    Rancho Santa Margarita
    CA  92688-2132
    U.S.A.
    T el: 800-242-3454 (949)-457-0200
    Fax: 800-457-3454 (949)-457-7878
    E-Mail: [email protected]
    Canada
    EIKI CANAD A - Eiki International, Inc.
    P .O. Box 156, 310 First St. - Unit 2,
    Midland, ON, L4R 4K8, Canada
    T el: 800-563-3454 (705)-527-4084
    Fax: 800-567-4069 (705)-527-4087
    E-Mail: [email protected]
    Deutschland & Österr eich
    EIKI Deutschland GmbH
    Am Frauwald 12
    65510 Idstein
    Deutschland
    Tel: +49-6126-9371-0
    Fax: +49-6126-9371-14
    E-Mail: [email protected]
    Eastern Eur ope
    EIKI CZECH SPOL. s.r .o.
    Nad Cementárnou  1163/4a
    Praha 4, Podolí
    147 00
    Czech Republic
    T el: +420 241 410 928
           +420 241 403 095
    Fax: +420 241 409 435
    E-Mail: [email protected]
    China
    EIKI (Shanghai) Co., Ltd.
    LAKESIDE OASIS MIDDLE RING 
    BUSINESS CENTRE
    Block 1, Room 606,
    1628, Jin Sha Jiang Road
    Shanghai, 200333
    CHINA
    T el:                      86-21-3251-3993
    Service Hot line: 86-21-3251-3995
    Fax:                     86-21-3251-3997
    E-mail: [email protected]
    South East  Asia
    EIKI Industrial (M) Sdn Bhd
    No. 1 1, Nouvelle Industrial Park,
    Lorong  Teknologi  B, Taman  Sains  Selangor 
    1, Kota Damansara PJU5,
    47810 Petaling Jaya, Selangor Darul Ehsan,
    Malaysia
    T el: +603-6157-9330
    Fax: +603-6157-1320
    E-Mail: [email protected]
    Japan &  Worldwide
    EIKI Industrial Company Limited.
    6-23  Teramoto, Itami-shi, Hyogo,
    664-0026 JAP AN
    T el: +81-72-782-7492
    Fax: +81-72-781-5435
    W orldW ide Website  http://www .eiki.com 
    						
    All Eiki manuals Comments (0)

    Related Manuals for Eiki Projector LC-XNS2600 User Manual