Eiki Projector LC-XNS2600 User Manual

51
Webpage operation
1. Input IP address in address bar.  Refer to page 50 for obtaining IP address.
2. Input ID and password, click OK to display the webpage.
    Default ID: admin
    Default password: admin
3. Set the items for projector in webpage.Projector/Standby
Projector/PCAdj This page displays the current power supply state of the projector.  
While connecting signal, you can use Auto PC Adjust function, adjust the value of Fine sync, 
Total dots, Horizontal and Vertical.
Network Control  

52
Projector/Display
Projector/ColorAdjProjector/Input
This page displays Screen size, Menu position and Background.
You can select Image Mode, adjust value of Contrast /Brightness/Red/Green/Blue/Sharpness
in this page.
You can select input source in this page.
Network Control
VGA IN 1
VGA IN 2  

53
Network Control
Projector/Setting
You can set Input Search/Auto PC adj/On start /Lamp control/Blank /Freeze in this page.  

54
Maintenance and cleaning
Caution
Do not leave the projector with the AC power cord connected under an abnormal condition. 
It may result in fire or electric shock.
POWER indicator
flashes orange.
POWER indicator
lights orange.
POWER indicator
POWER indicator
POWER indicator
The POWER indicator shows the state of the function which protects the p\
rojector. Check the state 
of the POWER indicator to take proper maintenance.
The projector is shut down and the POWER 
indicator is flashing orange.
When...

55
Filter counter reset
Cleaning the filterMaintenance and cleaning
The air filter prevents dust from accumulating on the surface of the optical elements inside 
the projector. Should the air filter become clogged with dust particles, it will redu\
ce cooling 
fans’ effectiveness and may result in a buildup of internal heat and adversely affects the life of 
the projector. If the Filter warning icon appears on the screen, the air filter should be cleaned 
immediately. Clean the air filter following the...

56
Clean the cabinet
Clean the project lens
Maintenance and cleaning
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning 
cloth that contains non-abrasive camera 
lens cleaner, or use a lens cleaning paper or 
commercially available air blower to clean the 
lens.
Avoid using an excessive amount of cleaner. 
Abrasive cleaners, solvents, or other harsh 
chemicals might scratch the surface of lens.
Unplug the AC power cord before cleaning.
Gently wipe the projector...

57
Replace the lamp
When the projection lamp of the projector 
reaches its end of life,the Lamp replacement 
icon appears on the screen, please replace the  
lamp immediately.
Lamp cover
Screw
Screw
Handle
Maintenance and cleaning
Lamp replacement icon
A
8‘	jLamp replace
As temperature inside the projector is high, 
you should cool the projector for at least 45 
minutes before you open the lamp cover.When the lamp isn’t illuminated, it may indicate that the lamp has been damaged.
When you replace the...

58
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.●   Lamp  life  may  differ  from  lamp  to  lamp  and  according  to  the  environment  of  use.  There  is  no 
guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter 
period of time than other similar lamps.
●    If the projector indicates that the lamp should be replaced, i.e., if the WARNING...

59
Troubleshooting
Problems– Solutions
No power - Plug the power cord of the projector into the AC power outlet.
- Check whether the POWER indicator lights red.
- Only when the POWER indicator lights red you can power on the   
   projector again.(Page 20)
- Check the WARNING indicator. If it lights red, the projector can not be  
   powered on.(Page 54)
- Check the projection lamp.(Page 57)
- Unlock the “Key lock” function.(Page 41)
No initial displaying - Make sure that Logo function is not set to...

60
No Sound- Check the audio cable connection from audio input source.
- Adjust the audio source.(Page 25)
- Press the VOLUME + button.(Page 25)
- Press the Mute button.
-   When the AUDIO OUT is plugged in, the projector’s built-in speaker is not 
available.
-    Is the image projected? The sound can only be heard when the image is 
projected.
The color is abnormal -   Check the input signal, color system, video system or computer system 
mode.
- Make sure that Blackboard is not selected in Image Mode...