Eiki Projector Lc Xb33 User Manual

51

Setting
This  function  is  used  to  reset  the  lamp  replacement counter.  When replacing the projection lamp, reset the lamp  replacement  counter  by  using  this  function.    See page 56 for operation.
Lamp counter 
Factory default
This  function  returns  all  setting  values  except  for  the user  logo,  PIN  code  lock,  Logo  PIN  code  lock,  and  the lamp counter to the factory default settings.
This  function  provides  the  following  alternatives  in  the cooling  fans'...

52

Maintenance and Cleaning
The WARNING TEMP. indicator shows the state of the function which protects the projector.  Check the state of the WARNING TEMP. indicator and the POWER indicator to take proper maintenance.
Warning Temp. Indicator
T h e  p r o j e c t o r  i s  s h u t  d o w n  a n d  t h e  WA R N I N G TEMP.  indicator is blinking red.
When  the  temperature  inside  the  projector  reaches  a certain  level,  the  projector  is  automatically  shut  down to  protect  the  inside  of  the...

53

Maintenance and Cleaning
Turn off the projector, and disconnect the AC power cord from the AC outlet.
Turn over the projector and remove the air filters by pulling the latches upward.
Air filters prevent dust from accumulating on the optical elements inside the projector.  Should the air filters become clogged with dust particles, it will reduce cooling fans' effectiveness and may result in internal heat build up and adversely affect the life of the projector.  Clean the air filters following...

54

Maintenance and Cleaning
Cleaning the Projector Cabinet
S o f t l y  w i p e  t h e  p r o j e c t o r  b o d y  w i t h  a  s o f t ,  d r y cleaning  cloth.    When  it  is  heavily  soiled,  use  a small  amount  of  mild  detergent  and  finish  with  a soft,  dry  cleaning  cloth.   Avoid  using  an  excessive amount  of  cleaner.   Abrasive  cleaners,  solvents,  or other harsh chemicals might scratch the surface.
Follow these steps to clean the projector cabinet.
When  the  projector  is  not...

55

Maintenance and Cleaning
When  the  life  of  the  projection  lamp  of  this  projector draws  to  an  end,  the  LAMP  REPLACE  indicator  emits a yellow light.  If this indicator lights yellow, replace the lamp with a new one promptly.
Lamp Replacement
WARNING:
TURN  OFF   THE   UV  LAMP   BEFORE
 
OPENING   THE   LAMP   COVER
Top Control
This  indicator  is  yellow  when the  life  of  the  projection  lamp draws to an end.
For continued safety, replace with a lamp of the same type.  Do not drop...

56

Maintenance and Cleaning
Be  sure  to  reset  the  Lamp  replacement  counter  after  the  lamp  is  replaced.    When  the  Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting.
Turn  the  projector  on,  press  the  MENU  button  to display  the  On-Screen  Menu.    Press  the  Point 7 8  buttons  to  move  the  red  framed  pointer  to  the Setting Menu icon.
P r e s s  t h e  P o i n t e d  b u t t o n s  t o  m o v e  t h e  r e d framed  pointer  to  the  Lamp  counter...

57

Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the i\
tems below once again.
– Make  sure  you  have  properly  connected  the  projector  to  peripheral  equipment  as  described  on 
pages15-17.
–  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When  you  operate  the  projector  with  a  computer  and  it  does  not  project  an  image,  restart  the 
computer.
– Solutions Problem 
 No power –  Plug the power cord of...

58

Appendix
WARNING:
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If  problems  still  persist  after  following  all  operating  instructions,  contact  the  dealer  where  you purchased  the  projector  or  the  service  center.    Give  the  model  number  and  explain  about  the problem.  We will advise you how to obtain service.
T h i s  s y m b o l  o n  t h e  n a m e p l a t e  m e a n s t h e  p r o d u c t  i s  L i s t e d  b y  U n d e r w r i t e...

59

Appendix
Menu Tree　
System (1)Mode 1Mode SVGA 1- - - -
Computer Input
✽ Systems  displayed  in  the  System  Menu  vary depending the input signal.
Computer Input/Video Input
Sound
On/OffSound0 - 63
InputComputer 1 
✽ N/A - - - not applicable
RGB Go to System (1)
N/A
Quit
RGB (Scart)
ComponentGo to System ()
AutoVideo
Video
S-Video
Quit
Go to System (3)
Go to System (3)
Go to System (3)
VolumeMuteQuit
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClamp
Display area - H...

60

Appendix
Dynamic
CinemaBlackboard (Green)Image 1Image Image 3
Image Select
Image 4
Standard
Video Input
Auto1080i1035i70p575p480p575i480i
System (2)
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
System (3)
Image AdjustContrastBrightness
Color temp.
RedGreenBlue
Gamma
Store
Quit
0 - 630 - 63
High
0 - 630 - 630 - 63
0 - 15
Image 1Image Image 3Image 4Quit
Mid
ResetYes/No
LowXLowAdj.
Sharpness0 - 15
Color0 - 63Tint0 - 63
Noise reductionOffL1LProgressiveOffL1LFilm
NormalWideScreen
Setting...