Eiki Projector Lc Xb27n User Manual

51
Setting
On start
When this function is “On”, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
✔Note:
Be sure to turn the projector off properly (see “Turning Off the
Projector” on page 22).  If the projector is turned off in the incorrect
sequence, the On start function does not operate properly.
Lamp control
Remote control
This function allows you to change brightness of the
screen.
Normal ....normal brightness 
Auto  ........brightness according...

52
Setting
Key lock
If the top control accidentally becomes locked and you
do not have the remote control nearby, disconnect the
AC power cord from the AC outlet, and then with
pressing the SELECT button, reinsert the AC power
cord.  This will cancel the top control lock.Key lock
Select Key lock.  Choose one
of the alternatives with the
Point edbuttons and select
[Yes] to activate it.
Security (Key lock and PIN code lock settings)
This function allows you to use Key lock and PIN code
lock function to set...

53
Setting
The PIN code can be changed to your desired four-digit
number.
Select PIN code change with the Point 
dbutton, and
press the SELECT button to display the New PIN code
input dialog box.  
Select a number with the Point
7 8buttons and fix the
number with the SELECT button. Repeat it to complete
entering a four-digit number.  When the four-digit
number is fixed, the pointer will automatically move to
Set.  Then press the SELECT button.  
To Change the PIN code 
Change the PIN code
Select PIN code...

54
This function is used to reset the lamp replacement
counter.  When replacing the projection lamp, reset the
lamp replacement counter by using this function.  See page
59 for operation.Lamp counter 
Factory default
This function returns all setting values except for the user
logo,  PIN code lock, Logo PIN code lock and the lamp
counter to the factory default settings.
Select Factory default and
this box will appear.
Select [Yes] , and the next
box will appear. 
Factory default
Select [Yes] to
activate...

55
The WARNING indicator shows the state of the function which protects the projector.  Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance. 
Top Control
Wa rn ing Indicator
The projector is shut down and the WARNING
indicator is blinking red.
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down
to protect the inside of the projector.  The POWER indicator
is blinking while the projector is being cooled...

56
Maintenance and Cleaning
Turn off the projector, and disconnect the AC power
cord from the AC outlet.
Turn over the projector and remove the air filters by
pulling the latches upward.
1
2
Air filters prevent dust from accumulating on the optical elements inside the projector.  Should the air filters
become clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat
build up and adversely affect the life of the projector.  Clean the air filters following the...

57
Maintenance and Cleaning
Disconnect the AC power cord before cleaning.
When the projector is not in use, replace the lens
cover.
1
3
2
Follow these steps to clean the projection lens.
Cleaning the Projector Cabinet
Disconnect the AC power cord before cleaning.1
Softly wipe the projector body with a soft, dry cleaning
cloth.  When it is heavily soiled, use a small amount of
mild detergent and finish with a soft, dry cleaning
cloth.  Avoid using an excessive amount of cleaner.
Abrasive cleaners,...

58
Maintenance and Cleaning
When the life of the projection lamp of this projector draws
to an end, the LAMP REPLACE indicator emits a yellow
light.  If this indicator lights yellow, replace the lamp with a
new one promptly.
Follow these steps to replace the lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give the following
information to the dealer.
●
Model No. of your projector :  LC-XB27
●Replacement Lamp Type No. :  POA-LMP90...

59
Maintenance and Cleaning
Be sure to reset the Lamp replacement counter after the lamp is replaced.  When the Lamp replacement
counter is reset, the LAMP REPLACE indicator stops lighting.
Turn the projector on, press the MENU button to
display the On-Screen Menu.  Press the Point
7 8
buttons to move the red framed pointer to the Setting
Menu icon.
Press the Point edbuttons to move the red framed
pointer to the Lamp counter function and then press
the SELECT button.  The first dialog box appears and...

60
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described on page18-20. 
–Make sure all equipment is connected to AC outlet and the power is turned on.
–When you operate the projector with a computer and it does not project an image, restart the computer.  
Appendix
Problem:–Solutions
No power–Plug the power cord of the projector into the AC outlet.
–See if the...