Eiki Projector Lc Xb27n User Manual

21
Connect the projectors AC power cord into an AC
outlet.  The POWER indicator will be red.
Press the POWER ON-OFF button on the top control
or on the remote control.  The POWER indicator will
become green and the cooling fans will start to
operate.  The preparation display will appear on the
screen and the count down will start. 
2
3
1
16
The preparation display will disappear 
after 30 seconds.
4After the countdown, the input source that was
selected last and the Lamp mode status icon (see
page 51)...

22
Basic Operation
Press the POWER ON-OFF button on the top control
or on the remote control, and a message Power off?
will appear on the screen.  
Press the POWER ON-OFF button again to turn off the
projector. The POWER indicator will start to blink red,
and the cooling fans will keep operating.  (You can
select the level of fun quietness and rotation speed.
See page 54.)  At this time you can disconnect the AC
power cord even if the fans are still running.
1
2
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU...

23
Basic Operation
ON - OFF
POWERAUTO SET U
P
INPUTWARNINGLAMP REPLAMENU
- VOLUME+ VOLUME
SELECT
Top Control
Menu barPointer
(red framed ) Menu icon
Item data
Press the Point 7 8
buttons to adjust the
value.
SELECT
button
Pointer (red framed )
Press the Point edbuttons
to move the pointer.
Item
How to Operate the On-Screen Menu
MENU button
SELECT buttonPOINT buttons
On-Screen Menu
Quit  
Exit this menu.
The projector can be adjusted or set via the On-Screen
Menu. Refer to the following pages regarding...

24
Basic Operation
Menu Bar
PC System Menu
Used to select
computer
system.  (p31)
Image Adjust Menu
Used to adjust computer
image. 
[Contrast / Brightness /
Color temp. / White balance
(R/G/B) / Sharpness /
Gamma]  (p36, 37)
Setting Menu
Used to set the
projectors operating
configurations.
(p46-54)
Used to adjust
the volume or
mute the sound.
(p26)
Image Select Menu
Used to select an image
level among Dynamic,
Standard, Real,
Blackboard(Green), and
Image 1 ~ 4.  (p35)
For computer source
AV  System Menu...

25
Basic Operation
Basic Operation
•The arrows are white when there is no correction.
•The direction of the arrow being corrected turns red.
•The arrows disappear at the maximum correction.
•If you press the KEYSTONE button on the remote
control once more while the keystone dialog box is
being displayed, the keystone adjustment will be
canceled.
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control or the
AUTO SET button on the remote control,...

26
Basic Operation
1
2
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Sound Menu icon. 
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume.  The volume dialog
box will appear on the screen for a few seconds.
Press the MUTE button on the remote control to cut off the
sound.  To restore the sound to its previous level, press the
MUTE button again or press the VOLUME+/– buttons.
Mute function is...

27
Basic Operation
Remote Control
Remote Control Operation
For some frequently used operations, using the remote control is advisable.
Just pressing one of the buttons enables you to make the operation, and no need for calling up the On-Screen
Menu.
COMPUTER/VIDEO
/NETWORK button 
✔Note:
See the next page for the other buttons.
Press the FREEZE button on the remote control to freeze
the picture on the screen.  To cancel the Freeze function,
press the FREEZE button again or press any other button....

28
Basic Operation
black out ➜the captured image ➜normal ➜ • • • • •
Press the NO SHOW button on the remote control to black
out the image.  To restore to normal, press the NO SHOW
button again or press any other button.  When a projected
image is captured and set as “User” in the Logo selection
(p48), the screen changes each time you press the NO
SHOW button as follows.
The message will disappear after 4 seconds.
NO SHOW button
Press the P-TIMER button on the remote control.  The timer
display “00 : 00”...

29
Choose either Computer 1(Analog) or Computer 2 by
pressing the INPUT button on the top control or press the
COMPUTER button on the remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Input Menu icon.1
Input Menu
Press the Point edbuttons to move the red arrow
pointer to either Computer 1(Analog) or Computer 2,...

30
Computer Input
Choose Computer 1(Digital) by pressing the INPUT button
on the top control or press the COMPUTER button on the
remote control.
Before using these buttons, correct input source should be
selected through Menu operation as described below.
Press the MENU button to display the On-Screen
Menu.  Press the Point
7 8buttons to move the red
framed pointer to the Input Menu icon.1Input Menu
Press the Point edbuttons to move the red arrow
pointer to Computer 1(Digital), and then press the
SELECT...