Eiki Projector Lc Xb21b User Manual

Maintenance and Cleaning
51
The  WARNING  indicator  shows  the  state  of  the  function  which  protects  the  projector.    Check  the 
state of the WARNING indicator and the POWER indicator to take proper maintenance.
Warning Indicator
T h e  p r o j e c t o r  i s  s h u t  d o w n  a n d  t h e  WA R N I N G 
indicator is blinking red .
When  the  temperature  inside  the  projector  reaches  a 
certain  level,  the  projector  is  automatically  shut  down 
to  protect  the  inside  of  the...

Maintenance and Cleaning
5
Turn off the projector, and disconnect the AC power 
cord from the AC outlet.
Turn over the projector and remove the air filters by 
pulling the latches upward.
Air filters prevent dust from accumulating on the optical elements inside the projector.  Should the air 
filters become clogged with dust particles, it will reduce cooling fans' effectiveness and may result in 
internal heat build up and adversely affect the life of the projector.  Clean the air filters...

Maintenance and Cleaning
53
Cleaning the Projector Cabinet
Gently wipe the projector body with a soft, dry cleaning 
cloth.    When  it  is  heavily  soiled,  use  a  small  amount  of 
mild detergent and finish with a soft, dry cleaning cloth.  
Avoid  using  an  excessive  amount  of  cleaner.   Abrasive 
cleaners,  solvents,  or  other  harsh  chemicals  might 
scratch the surface.
When  the  projector  is  not  in  use,  put  the  projector  in 
an appropriate carrying case to protect it from dust...

Maintenance and Cleaning
54
When  the  life  of  the  projection  lamp  of  this  projector 
draws  to  an  end,  the  LAMP  REPLACE  indicator  emits 
a yellow light.  If this indicator lights yellow, replace the 
lamp with a new one promptly.
Lamp Replacement
WARNING:
TURN OFF THE  UV  LAMP  BEFORE
 OPENING  THE LAMP COVER
Top Control
For continued safety, replace with a lamp of 
the same type.  Do not drop a lamp or touch 
a  glass  bulb!    The  glass  can  shatter  and 
may cause injury.Allow  a...

Maintenance and Cleaning
55
Be  sure  to  reset  the  Lamp  replacement  counter  after  the  lamp  is  replaced.    When  the  Lamp 
replacement counter is reset, the LAMP REPLACE indicator stops lighting.
Turn  the  projector  on,  press  the  MENU  button  to 
display  the  On-Screen  Menu.    Press  the  Point ◄
►  buttons  to  move  the  red  framed  pointer  to  the 
Setting Menu icon.
Press  the  Point ▲▼  buttons  to  move  the  red 
framed  pointer  to  the  Lamp  counter  function  and 
t h e n...

Appendix
56
Troubleshooting
Before calling your dealer or service center for assistance, check the i\
tems below once again.
– Make  sure  you  have  properly  connected  the  projector  to  peripheral  equipment  as  described  on 
pages15-17.
–

  Make sure all equipment is connected to AC outlet and the power is turned on.
–  When  you  operate  the  projector  with  a  computer  and  it  does  not  project  an  image,  restart  the 
computer.
– Solutions Problem 
 No power –  Plug the power cord of...

Appendix
57
 Image is Left/Right reversed
  Image is Top/Bottom reversed–  Check the Ceiling/Rear function. (See page 45.)
–  Check the Ceiling function. (See page 45.)
 No sound–  Check audio cable connections from the audio input source.
–  Adjust the audio source.
–  Press the VOLUME + button. (See page 3.)
–  Press the MUTE button. (See page 3.)
–  Is the image projected? You will hear the sound only when the 
image is projected.
 The color is strange .–  C h e c k  t h e  I n p u t  s i g...

Appendix
58
WARNING:
High voltages are used to operate this projector . Do not attempt to open the cabinet .
If  problems  still  persist  after  following  all  operating  instructions,  contact  the  dealer  where  you 
purchased  the  projector  or  the  service  center.    Specify  the  model  number  and  explain  about  the 
problem.  We will advise you how to obtain service.
T h i s  s y m b o l  o n  t h e  n a m e p l a t e  m e a n s 
t h e  p r o d u c t  i s  L i s t e d  b y  U n d e r w r i...

Menu Tree
System (1)Mode 1Mode SVGA 1- - - -
Computer Input
 Systems  displayed  in  the  System  Menu  vary 
depending on the input signal.
Computer Input/Video Input
Sound
On/OffSound0 - 63
InputComputer 1RGB Go to System (1)
Quit
RGB (Scart)
ComponentGo to System (3)
VolumeMuteQuit
Auto PC Adj.Fine sync.Total dotsHorizontalVerticalCurrent modeClamp
Display area - H
ResetMode free
0 - 31PC Adjust
Mode 3Mode 4Mode 5Quit
Yes/No
H-sync freq.V-sync freq.Quit
Mode 1Mode 
Display area - V
Store...

Appendix
60
Dynamic
CinemaBlackboard (Green)Image 1Image Image 3
Image Select
Image 4
Standard
Video Input
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Auto1080i1035i70p575p480p575i480i
System (2)
System (3)
Image AdjustContrastBrightness
Color temp.
RedGreenBlue
Gamma
Store
Quit
0 - 630 - 63
High
0 - 630 - 630 - 63
0 - 15
Image 1Image Image 3Image 4Quit
Mid
ResetYes/No
LowXLowAdj.
Sharpness0 - 15
Color0 - 63Tint0 - 63
Noise reductionOffL1LProgressiveOffL1LFilm
NormalWideScreen
Setting...