Eiki Projector Lc Xb21a User Manual

Setting
41
Video Input
Blue back
Press  the  Point ◄►  buttons  to  switch  On/Off.    When this  function  is  "On",  a  blue  image  is  displayed  while the input signal is not detected. 
Keystone
Press  the  MENU  button  to  display  the  On-Screen Menu.    Press  the  Point ◄►  buttons  to  move  the red framed pointer to the Setting Menu icon.
Language
T h e   l a n g u a g e   u s e d   i n   t h e   O n - S c r e e n   M e n u   i s available  in  English,  German,  French,  Italian,...

SettingSetting
4
Display
Press  the  Point ◄►  buttons  to  switch  On/Off.  This function decides to display On-Screen Displays.On. . . . . . . . . . . . . Show  all  the  On-Screen  Displays. Use  this  function  when  you  want to  project  images  after  the  lamp becomes  bright  enough.    Factory default setting is this mode.Countdown off  . . .  Show  the  input  image  instead  of the  countdown  when  turning  on the  projector.    Use  this  function w h e n  y o u  w a n t  t o  p r o j...

Setting
43
Setting
Capture
This  function  enables  you  to  capture  the  image being  projected  and  use  it  for  a  start-up  display  or interval of presentations.A f t e r  c a p t u r i n g  t h e  p r o j e c t e d  i m a g e ,  g o  t o  t h e Logo  select  function  and  set  it  to  "User".    Then the  captured  image  is  displayed  when  turning  on the  projector  next  time  or  pressing  the  NO  SHOW 
button. (p.4) 
To  capture  the  image,  select  [Yes].    To  cancel...

SettingSetting
44
To Enter the Logo PIN code
Select a number by pressing the Point ▲▼ buttons. And then press the Point ► button to fix the number and move the pointer.  The number changes to "".  If  you  fixed  an  incorrect  number,  move  the  pointer to  the  number  you  want  to  correct  by  pressing  the Point ◄  button,  and  then  select  the  correct  number by pressing the Point ▲▼ buttons.
Repeat  this  step  to  complete  entering  a  four-digit number.
A f t e r  e n t e r i n g...

Setting
45
Setting
Ceiling
When  this  function  is  "On",  the  picture  is  top/bottom and  left/right  reversed.   This  function  is  used  to  project the image from a ceiling mounting the projector.
Rear
When  this  function  is  "On",  the  picture  is  left/right reversed.   This  function  is  used  to  project  the  image  to a rear projection screen.
Ceiling 
Rear 
Input search
This  function  detects  the  input  signal  automatically. When  finding  a  signal,  the  search...

SettingSetting
46
Power management
F o r   r e d u c i n g   p o w e r   c o n s u m p t i o n   a s   w e l l   a s maintaining  the  lamp  life,  the  Power  management f u n c t i o n  t u r n s  o f f  t h e  p r o j e c t i o n  l a m p  w h e n  t h e projector is not used for a certain period.When  the  input  signal  is  interrupted  and  no  button  is pressed  for  more  than  30  seconds,  the  timer  display with "No signal" appears.  The countdown starts to turn off the lamp.
Select...

Setting
47
Setting
Remote control
This  projector  provides  two  different  remote  control codes:  the  factory-set  initial  code  (Code  1)  and  the  
secondary  code  (Code ).    This  switching  function 
prevents  remote  control  interference  when  operating several  projectors  or  video  equipment  at  the  same time.
When  operating  the  projector  in  "Code  ",  both  the 
projector  and  the  remote  control  must  be  switched  to 
"Code ".
To change the...

SettingSetting
48
Key lock
Security (Key lock and PIN code lock settings)
T h i s  f u n c t i o n  a l l o w s  y o u  t o  u s e  K e y  l o c k  a n d  P I N code  lock  function  to  set  the  security  for  the  projector operation.
This  function  locks  operation  of  the  top  control  or the remote control.It  is  useful  to  prevent  operation  by  an  unauthorized person.
. . . . . . not locked.
. . . . . .  lock  the  operation  of  the  top c o n t r o l .  To  u n l o c k ,  u s e  t h e...

Setting
49
Setting
To Enter the PIN code
Select a number by pressing the Point ▲▼ buttons. And then press the Point ► button to fix the number and move the pointer.  The number changes to "".  If  you  fixed  an  incorrect  number,  move  the  pointer to  the  number  you  want  to  correct  by  pressing  the Point ◄  button,  and  then  select  the  correct  number by pressing the Point ▲▼ buttons.
Repeat  this  step  to  complete  entering  a  four-digit number. 
A f t e r  e n t e r i n g  t...

Maintenance and CleaningSetting
50
This  function  is  used  to  reset  the  lamp  replacement counter.  When replacing the projection lamp, reset the lamp  replacement  counter  by  using  this  function.    See page 55 for operation.
Lamp counter 
Factory default
This  function  returns  all  setting  values  except  for  the user  logo,  PIN  code  lock,  Logo  PIN  code  lock,  and  the lamp counter to the factory default settings.
This  function  provides  the  following  alternatives  in  the...