Eiki Projector Lc Xb100 User Manual

61

Information
The	WARNING	indicator	shows	the	state	of	the	function	which	protects	the	projector.	Check	the	state	of	the	
WARNING	indicator	and	the	POWER	indicator	to	take	proper	maintenance.	
wARNING	indicator
The	projector	is	shut	down	and	the	w ARNING	
indicator	is	blinking	red .
When	the	temperature	inside	the	projector	reaches	a	
certain	level,	the	projector	will	be	automatically	shut	down	to	
protect	the	inside	of	the	projector.	The	POWER	indicator	is	
blinking	while	the	projector	is	being...

6

Maintenance	and	Cleaning
Turn	off	 the	projector,	 and	unplug 	the 	AC 	power 	cord	
from	the	 AC	outlet.
Turn	the	projector	over	and	remove	the	filters	.
1

Filter	prevents	dust	from	accumulating	on	the	optical	elements	inside	the	projector.	Should	the	filters	become	
clogged	with	dust	particles,	it	will	reduce	cooling	fans’ 	effectiveness	and	may	result	in	internal	heat	buildup	
and	adversely	affect	the	life	of	the	projector.	If	a	“Filter	warning”	icon	appears	on	the	screen,	clean	the...

6

Maintenance	and	Cleaning
Cleaning	the	Projector	Cabinet
Cleaning	the	Projection	Lens
Unplug	the	AC	power	cord	before	cleaning.
Gently	wipe	the	projection	 lens	with	a	cleaning	 cloth	that	
c o n t a i n s 	a 	s m a l l 	a m o u n t 	o f 	n o n - a b r a s i v e 	c a m e r a 	l e n s	
c l e a n e r, 	o r 	u s e 	a 	l e n s 	c l e a n i n g 	p a p e r 	o r 	c o m m e r c i a l l y	
available	air	blower	to	clean	the	lens.	
Avoid 	using 	an 	excessive 	amount 	of 	cleaner. 	Abrasive	
cleaners,...

64

Maintenance	and	Cleaning
When	the	projection	lamp	of	the	projector	reaches	its	end	
of	life,	the	Lamp	replacement	icon	appears	on	the	screen	
and	LAMP	REPLACE	indicator	lights	yellow.	Replace	the	
lamp	with	a	new	one	promptly.	 The	timing	when	the	LAMP	
REPLACE	indicator	should	light	is	depending	on	the	lamp	
mode.
Follow	these	steps	to	replace	the	lamp.
For	continued	safety,	replace	with	a	lamp	of	the	
same	type.	Do	not	drop	a	lamp	or	touch	a	glass	
bulb!	The	glass	can	shatter	and	may	cause...

65

Maintenance	and	Cleaning
This	projector	uses	a	high-pressure	lamp	which	must	be	handled	carefully	and	properly.		
Improper	handling	may	result	in	accidents,	injury,	or	create	a	fire	hazard.
●	Lamp	 life	may	 differ	 from	lamp	 to	lamp	 and	according	 to	the	 environment	 of	use.	 There	 is	no	 guarantee	
of	the	 same	 life	for	each	 lamp.	 Some	 lamps	 may	fail	or	terminate	 their	life	in	a	shorter	 period	of	time	
than	other	similar	lamps.
●	If	 the	 projector	 indicates	 that	the	lamp	 should	 be...

66

	 Problem:	–	Solutions
	 No	power	–	Plug	the	power	cord	of	the	projector	into	the	AC	outlet.	
	 	 –	See	if	the	POWER	indicator	lights	red.	
	 	–		
Wait	until	the	POWER	indicator	stops	blinking	to	turn	on	the	projector	
again.	 The	projector	can	be	turned	on	after	the	POWER	indicator	
turns	red.	See	page	20.
	 	 –	Check	the	WARNING	indicator.	If	the	WARNING	indicator	lights	red,																	
																																																																					projector	cannot	be	turned	on.	See...

67

Appendix
	No	image	–	Check	the	connection	between	your	computer	or	video	equipment		
	 	 	 and	the	projector.	See	pages	16-18.	
	 	–	See	if	the	input	signal	is	correctly	output	from	your	computer.	Some		
	 		 laptop	computers	may	need	to	change	the	setting	for	monitor	output		
	 				when	connecting	to	a	projector.	See	your	computer’s	instruction		
	 		 manual	for	the	setting.		
	 	–	It	takes	about	30	seconds	to	display	an	image	after	turning	on	the		
	 		 projector.	See	page	20.
	 	–		
Check	the...

68

Appendix
	 The	image	is	distorted	or	runs	off .	–	Check	PC	adjustment	menu	or	Screen	and	adjust	them.		 	
	 				See	pages	33-34,	37-38.
	 PIN	code	dialog	box	appears	 –	PIN	code	lock	is	being	set.	Enter	a	PIN	code	(the	“1234”	or	numbers	
	at	start-up .		 you	have	set).	See	pages	21,	56-57.
	Page	Up/Down	function	does	not		–	Make	sure	the	USB	infrared	receiver	is	connected	to	the	USB	port	of		
	work .	 	your	computer.	See	page	14.			 		 	 	
	 	 –	Check	cable	connection	between	the	projector		and	your...

69

wARNING	:
High	voltages	are	used	to	operate	this	projector  .	Do	not	attempt	to	open	the	cabinet .
If	problems	still	persist	after	following	all	operating	instructions,	contact	the	dealer	where	you	purchased	the	
projector	or	the	service	center.	Specify	the	model	number	and	explain	about	the	problem.	We	will	advise	you	
how	to	obtain	service.
This	symbol	 on	the	 nameplate	
m e a n s 	t h e 	p r o d u c t 	i s 	L i s t e d	
by	 Underwriters	 Laboratories	
I n c .	 	I t	i s 	d e s i g n e d 	a n d	
m...

70

Appendix
Menu	Tree
SVGA	1Mode	1Mode	2	-	-	-	-
Total	dotsHorizontalVertical
Display	area	HDisplay	area	VReset
Dynamic
RealBlackboard	(Green)
Image	1Image	2Image	3
Image	 AdjustContrastBrightnessColor	temp.
Red
Gamma
Store
NormalTrue
Digital	zoom	–
Full	
0–630–63
Computer	Input
PC	adjust
Mode	1Mode	2Mode	3Mode	4Mode	5
Image	select
0–63
0–15
Image	1Image	2Image	3Image	4
Screen
Yes/No
	*	Systems	displayed	in	the	System	Menu	vary	depending	on	an	input	signal.
ResetYes/No
Sharpness0–15
Computer...