Eiki Projector Lc X85 User Manual

81
Optional Parts
Lens Replacement
The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector 
for wide variety of uses.
For installation and replacement of the lens, always contact the sales dealer. The projector lens must be 
installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by 
yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause...

82
Configurations of Terminals
ANALOG/ MONITOR OUT (Mini D-sub 15 pin)
512341096781514131 112
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1
2
3
4
5
6
7
8
DIGITAL DVI-D (DVI 24 PIN)
1917
21018
31 119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5
2
4
3
6
7
8
T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot Plug...

83
Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or 
lost the number and unable to operate the projector, contact the service station. 
Factory default set No:  1 2 3 4*
Factory default set No:  4 3 2 1*
*  S h o u l d   t h e   fo u r- d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked with a PIN code. While the...

84
Dimensions
Appendix
3.94 (100)
14.57 (370)
5.75 (146)
17.32 (439.9) 13.58 (345)
4.13 (105)
5.20 (132) 4.33 (110)
4.33 (110)
7.36 (187)
6.5º MAX
  )8 +=   52+9  ,58    +/2/4 -   5; 4:
  )8 +=      
 +6 :.                
2.05 (52)
Unit: inch (mm) 

85
Serial Control Interface
Appendix
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to CONTROL 
PORT on the projector and serial port on the PC.
 (See p.22)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for...

86
The command is sent from PC to the projector with 
the format below;
     'C' [Command] 'CR'
        Command: two characters (refer to the 
command table below.
-The projector decodes the command and returns the 
'ACK' with the format below;
      'ACK'  'CR'
-When the projector can not decode the command, it 
returns with format below.
      ‘?’  ‘CR’ 
Format
Appendix
Functional Execution Command
Command
Function
C00 Turn the projector ON
C01 Turn the projector...

87
Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Character string' with the format below; Format
The tables on page 86 and 87 show the typical command lists for controlling the projector.  Please consult your 
local dealer for further information of other commands.
Command...

 
 
 
 
 
 
U.S.A. 
EIKI International, Inc. 
30251 Esperanza 
Rancho Santa Margarita 
CA 92688-2132 
U.S.A. 
Tel :   800-242-3454 (949)-457-0200 
Fax :   800-457-3454 (949)-457-7878 
E-Mail : [email protected] 
 
Deutschland & Österreich 
EIKI Deutschland GmbH 
Am Frauwald 12 
65510 Idstein 
Deutschland 
Tel :   06126-9371-0 
Fax :   06126-9371-14 
E-Mail : [email protected] 
 
 
 
China 
EIKI (Shanghai) Co., Ltd. 
1. Dapu Road, 
Golden Magnolia Plaza 
#2109 Shanghai, 
200023 China 
Tel :  86-21-5396-0088 
Fax :...