Eiki Projector Lc X80 User Manual

							
41

AV SySTEM MENU (VIDEO OR S-VIDEO)
AV S ySTEM MENU (COMPONENT VIDEO)
Video System Selection
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
AV System Menu icon.
Use the Point ed buttons to move the red arrow pointer to 
the desired system and then press the SELECT button.
1
2
If the projector cannot reproduce proper video image, select a 
specific broadcast signal format from among PAL, SECAM, NTSC, 
NTSC 4.43, PAL-M, and PAL-N. PAL/SECAM/NTSC/NTSC4 .4/PAL-M/PAL-N
The projector automatically detects an incoming video signal, and 
adjusts itself to optimize its performance.
When the Video System is 1035i or 1080i, select the system 
manually.
If the projector cannot reproduce proper video image, select a 
specific component video signal format from among 480i, 575i, 
480p, 575p, 720p, 1035i, and 1080i.
Auto
COMPONENT VIDEO SIGNAL FORMAT
Video Jack or S-Video Jack
y, Pb/Cb, Pr/Cr Jacks
The projector automatically detects an incoming video system, and 
adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system manually.
Auto
AV System Menu iconThe selected system is displayed
Move the pointer to the desired system and press the SELECT button.
AV System Menu iconThe selected system is displayed.
Move the pointer to the desired system and press the SELECT button.
Video Input 
						

							
4

Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Image Select Menu icon.
1
2Use the Point ed buttons to move the red frame pointer to 
the desired image level and then press the SELECT button.
IMAGE SELECT MENU
Image Level Selection
Move the red frame pointer to the desired level and press the SELECT button.
Image Select Menu icon
Normal picture level preset on the projector.
Standard
Picture level adjusted with fine tone.
Cinema
User preset picture adjustment in the Image Adjust Menu. (p. 47)
IMAGE 1–10
Menu Operation
Video Input 
						

							
4

Screen Size Adjustment
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Screen Menu icon.
Use the Point ed buttons to move the red frame pointer to 
the desired function and then press the SELECT button.
1
2
✔Note:
	 •	 Wide	cannot	be	operated	when	“720p,”	“1035i,”	
or	 “1080i”	is	selected	on	 AV	System	Menu	(p.41).
SCREEN MENU
Provide the image at the wide screen ratio of 16:9.
Wide
Provide the image at the normal video aspect ratio of 4:3.
NormalMove the red frame pointer to the desired function and press the SELECT button.
Screen Menu icon
 Scale H/V  ..............  Adjust the Horizontal/Vertical screen scale.
  H&V  ......................  When set to “On,” the aspect ratio is fixed. 
The “Scale V” appears dimmed and becomes 
unavailable. Adjust “Scale H,” then the screen 
scale is automatically modified based on the 
aspect ratio. 
  Position H/V  ..........  Adjust the Horizontal/Vertical screen position.
  Common  ..............  Save the adjusted scale to all the inputs. 
Press the SELECT button at Common to 
display a confirmation box. To save the scale, 
press the SELECT button at “Yes.” When 
Custom is selected, the saved scale is used.
  Reset  ....................  Reset the all adjusted values. Press the 
SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT 
button at “Yes.”
Custom
✔Note:
	 •	 When	no	signal	is	detected,	 “Normal”	is	
set	automatically	and	the	 Aspect	dialog	box	
disappears.
	 •	 The	adjustable	range	for	Scale	H/V	and	Position	 H/V	is	limited	depending	on	the	input	signal.
Press the SELECT button at Common or Reset, to display a confirmation box.
Video Input
Adjust the screen scale and position manually with this function.
Press the SELECT button at Custom and the “Custom” is displayed 
on the screen for a few seconds. To display the Aspect dialog box, 
press the SELECT button at Custom again and then the Aspect 
dialog box appears. 
						

							
44

Keystone
This function is used to store or reset the keystone correction 
when the AC power cord is unplugged. Use the Point 7 8 buttons 
to switch between each option. 
 Store
. . .  Keep the keystone correction even when the AC power 
cord is unplugged.
  Reset
  . .  Release the keystone correction when the AC power 
cord is unplugged.
To correct keystone distortion, press the Select button. The 
Keystone dialog box appears. Use the Point ed7 8 buttons to 
correct keystone distortion. (p.29)
Ceiling 
Rear 
Ceiling
When this function is set to “On,” the picture is top/bottom and 
left/right reversed. This function is used to project the image from a 
ceiling-mounted projector.
Rear
When this function is set to “On,” the picture is left/right reversed. 
This function is used to project the image from the rear of the   
screen.
Reset
This function returns all adjusted values to the factory default 
settings. Press the SELECT button at Reset to display a 
confirmation box. To reset, press the SELECT button at “Yes.”
SCREEN MENU
Move the red frame pointer to a function and press the SELECT button.
Video Input
Exit the Screen Size Adjustment Menu.
Quit 
						

							
45

Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Image Adjust Menu icon.
1
2Use the Point ed buttons to move the red frame pointer to 
the desired item and then press the SELECT button to display 
the adjustment dialog box. Use the Point 7 8 buttons to 
adjust the setting value.
IMAGE ADJUST MENU
Press the Point 7 button to decrease contrast; press the Point 8 
button to increase the contrast (from 0 to 63).
Press the Point 7 button to decrease the brightness; press the 
Point 8 button to increase the brightness (from 0 to 63).
Contrast
Brightness
Press the Point 7 button to decrease the intensity of the color; 
press the Point 8 button to increase the intensity of the color (from 
0 to 63).
Press the Point 7 8 buttons to adjust the tint value to obtain 
proper color balance (from 0 to 63).
Color ✽
Tint ✽
Color Management
The Color Management function can be used to adjust the LEVEL, 
PHASE, and GAMMA of the selected display colors (except for 
black, white, and gray) on the screen and replace these colors with 
other colors if required.
You can store up to eight (8) color management data.
1Use the Point ed buttons to move the red frame pointer to 
Color Management, and then press the SELECT button. The 
projected image freezes, and the COLOR MANAGEMENT 
POINTER appears.
Use the Point ed7 8 buttons to move the pointer to the 
spot where you want to adjust the color and then press the 
SELECT button. The COLOR SELECTION window appears, 
and the color in the center of the pointer is selected and you 
can adjust the color.
2
Use the Point ed7 8 buttons to adjust the LEVEL and 
PHASE of the color, and then press the SELECT button to 
confirm the setting. Then use the Point ed buttons to adjust 
the GAMMA for the color and press the SELECT button to 
accept the setting. After adjusting, press the SELECT button 
to go to the COLOR MANAGEMENT LIST.
3
COLOR MANAGEMENT POINTER
POINTER MODE
Image Adjustment
Move the red frame pointer to the desired item and then press SELECT button.
Image Adjust Menu icon
Use the Point 7 8 buttons to adjust the setting value.
COLOR SELECTION MODE
Go to the COLOR MANAGEMENT LIST.
LIST
Picture Image
✔Note:
	 •				Displayed	only	in	 Video	Input.	 •	Tint	cannot	be	selected	when	the	video	system	
is	PAL,	SECAM,	PAL-M,	or	PAL-N	(p.41).
✽ 
						

							
46

Auto picture control
Use the Point 7 8 buttons to select the desired Auto picture 
control position (Off, L1 or L2).
 Off
  . . . .  Auto picture control OFF position.
  L1
. . . . .  Auto picture control LEVEL 1 position.
  L2
. . . . .  Auto picture control LEVEL 2 position.
Clear the check mark if you do not want to apply the adjusted 
color data; select the check mark and then press the SELECT 
button. The check mark disappears.
Return to the COLOR MANAGEMENT POINTER. (If you press 
the MENU button on the side control or the remote control, it 
returns to the COLOR MANAGEMENT POINTER and you will 
need to reselect and readjust the color.)
Return to the IMAGE ADJUST Menu. Any settings that 
have been changed will not be stored. To store the changed 
settings, be sure to select “LIST” and go to the COLOR 
MANAGEMENT LIST.
LIST MODE
Return to the COLOR SELECTION mode so that you can 
readjust the setting for the color in that line. (This option is 
not available if the check mark is cleared.)
Select the DEL box if you want to delete the adjusted data. 
Press the SELECT button and a confirmation box appears and 
then select [Yes] 
Delete all the data in the list. Press the SELECT button and a 
confirmation box appears and then select [Yes].
The same function as stated above.
Level and phase adjustment palette.Gamma adjustment palette.
Color temp .
Use the Point 7 8 buttons to select the desired Color temp. level 
(High, Mid, Low, or XLow). 
COLOR M .
MENU
COLOR PALETTE
DEL
ALL DEL
COLOR M .
LISTCOLOR M .MENU
COLOR PALETTE
DEL
ALL DELMENUCOLOR M .
COLOR SELECTION MODE
LIST MODE
COLOR SELECTION MODE (continued)
In the COLOR MANAGEMENT LIST, the adjusted color data 
are checkmarked. You can decide whether or not to apply the 
adjusted color data in the list to the projected image (see 
below).
4
MENU
The same function as stated above.
Picture Image 
						

							
47

Use the Point 7 8 buttons to adjust the gamma value to obtain a 
better balance of contrast (from 0 to 15).
Gamma
Press the Point 7 button to decrease the sharpness of the image; 
press the Point 8 button to increase the sharpness of the image 
(from 0 to 31).
Sharpness
An interlaced video signal can be displayed in progressive mode. 
Press the Point 7 8 buttons to change the progressive scan mode. 
  Off
  . . . .  Progressive scan mode is “Off.”
  On
  . . . .  Progressive scan mode is “On.”
  Film
  . . .  For watching a film. With this function, the projector 
reproduces pictures faithful to the original film quality.
Noise interference on the screen can be reduced. Press the Point 
7 8 buttons to change the noise reduction mode.
  Off
  . . . .  Noise reduction mode is “Off”
  On
  . . . .  Noise reduction mode is “On”
Noise reduction ✽
Progressive ✽
Store iconPress the SELECT button at this icon to store the adjustment.
Press the Point 7 button to lighten red/green/blue tone; press the 
Point 8 button to deepen red/green/blue tone (from 0 to 63).
White balance (Red/Green/Blue)
Press the Point 7 button to lighten red/green/blue tone of the black 
level of an image; press the Point 8 button to deepen red/green/
blue tone of the black level of an image (from 0 to 63).
Offset (Red/Green/Blue)
Exit the Image Adjust Menu.
To store the adjusted data, move the red frame pointer to the Store 
icon and press the SELECT button. The Image Level Menu appears. 
Move the red arrow pointer to any of the Image 1 to 10 in which 
you want to set and press the SELECT button. A confirmation box 
appears and then select [Yes].
To reset the adjusted data, select Reset and press the SELECT 
button. A confirmation box appears and then select [Yes]. All 
adjustments will return to their previous figures.
Reset
Store
Quit
Press the SELECT button at this icon to display other items.
Press the SELECT button at this icon to display the previous items.
Press the Point 7 8 buttons to adjust the setting value.
Picture Image
Image Level MenuMove the red frame pointer to an image item to be set and then press the SELECT button.
✔Note:
	 •	 			Displayed	only	in	 Video	Input.	 •	When	the	 White	balance	Red,	Green,	or	Blue	is	adjusted,	the	Color	
temp.	level	will	change	to	 “Adj.”
	 •	 The	Film	mode	in	the	Progressive	function	cannot	be	selected	 when	the	video	signal	format	is	1080i	or	1035i.
	 •	 Progressive	cannot	be	selected	when	 “480p,”	“575p,”	or	 “720p”	is	
selected	(p.41).
✽ 
						

							
48

Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Setting Menu icon.
1
2
Language
The language used in the On-Screen Menu is available in English, 
German, French, Italian, Spanish, Portuguese, Dutch, Swedish, 
Russian, Chinese, Korean, or Japanese.
Use the Point ed buttons to move the red frame pointer 
to the desired item and then press the SELECT button. The 
Setting dialog box appears.
Press the SELECT button at Language, then the Language Menu appears.
SETTING MENU (Language)
This projector has a Setting menu that allows you to set up other various functions.
Background
The selected background screen will be displayed when no input 
signal is detected.
 Blue
  . . .  Blue colored background.
  User
 . . .  The image you captured.
  Black
. . .  Black colored background.
Setting
Set the red frame pointer to the item and press the SELECT button.
Setting Menu icon
When this function is set to “On,” the value adjustment bar in the 
Picture Image Adjustment Menu appears on the screen.
Simple menu
Menu
This function is used to adjust the On-Screen Menu display 
position. Press the SELECT button and the adjustment screen 
appears (arrows appear). Use the Point ed7 8 buttons to adjust 
the position. After making the adjustment, press the SELECT 
button to return to the Menu screen.
Position
This function allows you to adjust the position of the On-Screen 
Display and the value adjustment bar in the Picture Image 
Adjustment Menu.
Display
This function decides whether to display On-Screen Displays.
  On
  . . . . . . . . . . . .  Shows all the On-Screen Displays. Use this 
function when you want to project images 
after the lamp becomes bright enough. The 
factory default setting is in this option.
  Countdown Off
. . .  Show the input image instead of the 
countdown when turning on the projector. 
Use this function when you want to project 
the image as early as possible even when the 
lamp is not bright enough. 
  Off
  . . . . . . . . . . . .  Hide the On-Screen Displays except:
      ● 
On-Screen Menu
     ● “Power off?” (p.24)
     ●  Color management operation screen 
(pp.45-46)
     ●  “No signal” for Power management (p.52)
     ●  P-TIMER (p.29)
     ●  ”Please wait....”
     ● Arrows for the True function in the Screen 
Menu (p.39)
Menu
Set the red frame pointer to the item and press the SELECT button.
✔Note:
	 •	 User		cannot	be	selected	when	the	image	is	not	captured.
Setting 
						

							
49

This function allows you to customize the screen logo with Logo 
select, Capture, and Logo PIN code lock functions.Logo
✔Note:
	 •	 Before	capturing	an	image,	select	“Standard”	in	the	Image	
Select	Menu	to	capture	a	proper	image.	(pp.	38,	42)
	 •	 A	signal	from	a	computer	can	be	captured	up	to	XGA	(1024	X	
768).
	 •	 Certain	signals	may	not	be	captured	properly.
	 •	 When	capturing	the	image	that	has	been	adjusted	by	the	 Keystone	function,	the	adjusted	data	is	automatically	reset	and	
the	projector	captures	an	image	without	keystone	correction.	
	 •	 When	starting	to	capture	a	new	image,	the	previously	stored	 image	is	cleared	even	if	you	cancel	the	capturing.
	 •	 Once	you	exit	the	Logo	Menu	after	setting	the	Logo	lock	to	 "On,"	you	are	required	to	enter	the	PIN	code	every	attempting	to	
change	the	Logo	setting.
	 •	 User	cannot	be	selected	when	the	image	is	not	captured.
Select [Yes] to capture the projected image.
This function decides on the starting-up display from among the 
following options.
  User
 . . .  Show the image you captured.
  Default
  .  Show the factory-set logo.
  Off
  . . . .  Show the countdown display only.
Capture
Select [Yes] to stop capturing.
Logo select
Logo
✔Note:
	 •	 When	 “On”	is	selected	in	the	Logo	PIN	code	lock	function,	Logo	
select	and	Capture	functions	cannot	be	selected.
This function enables you to capture an image being projected to 
use it for a starting-up display or interval of presentations.
Select Capture and press the SELECT button.  
A confirmation box appears and select [Yes] to capture the 
projected image.
After capturing the projected image, go to the Logo select 
function and set it to “User”. Then the captured image will be 
displayed the next time you turn on the projector.
To cancel the Capture function, select [No].
Set the red frame pointer to the item and press the SELECT button.
Capture
Set the red frame pointer to the item and press the SELECT button.
Setting 
						

							
50

Change the Logo PIN code lock setting
After a correct Logo PIN code is entered, the following dialog box appears.
Use the Point 7 8 buttons to switch On/Off,
This function prevents an unauthorized person from changing the 
screen logo.
 Off
  . . . .  The screen logo can be changed freely from the Logo 
Menu.
  On
  . . . .  The screen logo cannot be changed without a Logo 
PIN code.
If you want to change the Logo PIN code lock setting, press the 
SELECT button and the Logo PIN code dialog box appears. Enter 
a Logo PIN code by following the steps below. The initial Logo PIN 
code is set to “4321” at the factory.
Logo PIN code lock
Enter a Logo PIN code
Change the Logo PIN code
Logo PIN code can be changed to your desired four-digit number. 
Press the Point d button to select “Logo PIN code change” and 
then press the SELECT button. The New Logo PIN code input 
dialog box appears. Set a new Logo PIN code.  
Be sure to note the new Logo PIN code and keep it at hand. If you 
lost the number, you could no longer change the Logo PIN code 
setting. For details on PIN code setting, refer to “PIN code lock” 
on pages 53–54. Logo PIN Code Lock
Enter a Logo PIN code
Use the Point 7 8 buttons to switch On/Off, and then press the 
Point d button to move the pointer to “Quit.” Press the SELECT 
button to close the dialog box.
Change the Logo PIN code lock setting
CAUTION:
WHEN y
OU HAVE CHANGED THE LOGO PIN 
CODE,  WRITE DOWN  THE NEW PIN CODE 
IN COLUMN OF  THE LOGO PIN CODE NO .  
MEMO ON PAGE 76,  AND KEEP IT SECUREL y . 
SHOULD  THE LOGO PIN CODE BE LOST OR 
FORGOTTEN,  THE LOGO PIN CODE SETTING 
CAN NO LONGER BE CHANGED .
Change the Logo PIN code
Use the Point ed buttons on the side control or Number buttons 
on the remote control to enter a number. 
When using side control
Use the Point ed buttons on the side control to select a number. 
Press the Point 8 button to fix the number and move the red 
frame pointer to the next box. The number changes to “✳.” 
Repeat this step to complete entering a four-digit number. After 
entering the four-digit number, move the pointer to “Set.” Press 
the SELECT button so that you can change the Logo PIN code 
lock setting.
When using remote control
Press the Number buttons on the remote control to enter a 
number (p.14). When you complete entering a four-digit number, 
the pointer moves to “Set.” Press the SELECT button so that you 
can change the Logo PIN code lock setting.
 If you fixed an incorrect number, use the Point 7 button to move 
the pointer to the number you want to correct, and then enter the 
correct number.
If you entered an incorrect PIN code, “Logo PIN code” and the 
number (✳✳✳✳) will turn red for a moment. Enter the correct PIN 
code all over again.
Setting