Eiki Projector Lc X8 User Manual

51
Lamp control
Choose the running speed of cooling fans from the following 
options.
 Normal .......  Normal speed.
  Max ...........  Faster than the normal speed.
Fan control
This function allows you to change the brightness of the screen.
Auto  . . . . . 
 Brightness according to the input signal. 
Normal  . . .   Normal brightness. 
Eco  . . . . . .    Lower brightness.  Lower brightness reduces 
the lamp power consumption and extends the 
lamp life.
Setting
This Projector is equipped with 2...

52
Power management
Time left before the lamp is off
Press the SELECT button at Power 
management and the dialog box 
appears.  Use the Point 7 8 
buttons to choose one of the three 
options.
Press the Point d button to select 
the timer, and then use the Point 7 
8 buttons to set the timer
For reducing power consumption as well as maintaining 
the lamp life, the Power management function turns off the 
projection lamp when the projector is not used for a certain 
period.
If the input signal is...

53
Security
Key lockKey lock
Security
Select Key lock and 
this box appears. 
Choose one of the 
alternatives with the 
Point ed buttons 
and select [Yes] to 
activate it.
This function locks the side control and remote control buttons 
to prevent operation by unauthorized persons.. . . . .  Unlocked.
. . . . .   Lock the side control buttons.
  To unlock, use the remote control.
. . . . .   Lock the remote control buttons.  
To unlock, use the side control.
If the side control accidentally becomes...

54
Change the PIN Code 
Change the PIN code
CAUTION:
WHEN y OU HAVE CHANGED THE PIN CODE,  WRITE 
DOWN A NEW PIN CODE IN COLUMN OF  THE PIN CODE 
NO .  MEMO ON PAGE 80,  AND KEEP IT SECUREL y . IF 
y OU FORGET y OUR PIN CODE,  THE PROJECTOR CAN NO 
LONGER BE STARTED . The PIN code can be changed to your desired four-digit 
number. Press the Point d buttons to select “PIN code 
change” and press the SELECT button. The New PIN code 
input dialog box appears. Set a new PIN code.
Change the PIN Code Lock...

55
Setting
Shutter
Shutter function is available to block out light to the 
screen, so that the screen can be used for the other 
presenters.Prohibits the shutter operation from the remote control 
and the projector's side control.
Remote control     Selecting "On" prohibits the shutter 
operation from the remote control.  
Projector   . . .       Selecting "On" prohibits the shutter 
operation from the side control.
It is possible to prohibit the shutter operation from both of 
the...

56
Factory default
This function returns all setting values except for the user logo, 
PIN code lock, Logo PIN code lock, lamp counter, filter counter 
and filter timer to the factory default settings. Factory default
Quit
Exit the Setting Menu.
Select Factory default and this box 
appears. Select [Yes], and the next 
box appears. 
Test pattern
Various test pattern are available for use when setting up the 
projector.
Set the red frame pointer 
to the item and press the 
SELECT button.
Setting
Select...

57
Maintenance and Care
Filter Instructions
Filter prevents dust from accumulating on the optical elements inside the projector\
. Should the filter becomes 
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup 
and adversely affect the life of the projector. This projector has an electrically operated filter which helps you to 
replace the filter easily. The projector monitors the condition of the filter at all time and replac\
es a filter with...

58
Turn off the projector, press the Main On/Off Switch to 
Off and unplug the AC power cord from the AC outlet.
First, clean up the dust on the projector and around the 
air vents.
1
2
Slide and open the Filter cover.  (See the right figure.)3
Put the new one back into the position and close 
the filter cover. Make sure that the filter cartridge is 
properly and fully inserted.5
CAUTION
Make sure the filter cartridge is inserted in the 
projector. If the filter cartridge is not inserted, the 
projector...

59
Be sure to reset the Scroll counter after replacing the filter 
cartridge. 
Press the MENU button to display the On-Screen Menu. Use 
the Point 7 8 buttons to move the red frame pointer to the 
Setting Menu icon.
Use the Point ed buttons to move the red frame pointer to 
Filter counter and then press the SELECT button. A dialog 
box appears showing the Used time option and the Scrolls 
remaining option. Use the Point ed buttons to select  
Scroll(s) remaining.
1
2
Resetting the Scroll CounterScroll...

60
Lamp Management
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled \
by 
the Lamp Management Function.  The Lamp Management Function detects the status of lamps and shows the 
status on screen or on the LAMP 1/2 REPLACE indicators.  This function also automatically controls  the Lamp 
Mode when any of lamps is out for the end of life or malfunctions. Projection Lamp lights normally.
Lamp 1/2 Replace Indicators
The LAMP 1/2 REPLACE indicators...