Eiki Projector Lc X7 User Manual

							
81

Dimensions
Unit: inch (mm)
Appendix
5.81(
147.5
)
20.87(530)
20.65(524.5)
108°
8.66(220)8.46(215)
1.18(30)
7.28(185)
23.62(600)
200.0234.0
26.77(680)
3.03(77)
9.25(235)9.25(235)
29.80(757.0)
5.00(127)
9.63(244.5)10.53(267.5)
1.14(29)
9.82(249.5)
10.43(265)
10.89(276.5)
4.72(120)
8.27(210)
6.89(175)
Screw Holes for Ceiling MountScrew: M8Depth: 0.393 (10.0) 
						

							
8

Serial Control Interface
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial 
port.
Connect a RS-232C serial cross cable to SERIAL 
PORT IN on the projector and serial port on the PC.
 (See p.11)
Launch a communication software provided with PC 
and setup the communication condition as follows:
1
2
3
Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit   : 1
Flow control  : none
Data bit   : 8
Type the command for controlling the projector and 
then enter the "Enter" key. 
Example
When you want to change the input to INPUT 2, 
Type 'C' '0' '6' 'Enter'. 
✔Note:
• The default of the baud rate is set to 19200 bps. If an 
error occurs in the communication, change the serial 
port and the communication speed (baud rate).
•Enter with ASCII 64-byte capital characters and one-
byte characters.
The command is sent from PC to the projector with 
the format below;
      'C' [Command] 'CR'
        Command: two characters (refer to the 
command table below.
-The projector decodes the command and returns the 
'ACK' with the format below;
     'ACK'  'CR'
-When the projector cannot decode the command, it 
returns with format below.
     ‘?’  ‘CR’ 
Format
Operation
Appendix
Functional Execution Command
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF 
(immediately OFF)
C05Select Input 1
C06Select Input 2
C07Select Input 3
C08Select Input 4 
C0DVideo mute ON
C0EVideo mute OFF
C0FAspect 4:3
C10Aspect 16:9
C1CMenu ON
C1DMenu OFF
C3APointer RIGHT
CommandFunction
C3BPointer LEFT
C3CPointer UP
C3DPointer DOWN
C3FEnter
C46Zoom DOWN
C47Zoom UP
C4AFocus DOWN
C4BFocus UP
C5DLens shift UP
C5ELens shift DOWN
C5FLens shift LEFT
C60Lens shift RIGHT
C89Auto PC Adj.
C8EKeystone UP
C8FKeystone DOWN
C90Keystone RIGHT
C91Keystone LEFT 
						

							
8

Status Read Command
Appendix
The command is sent from PC to the projector with 
the format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command 
table below.
The projector decodes the command and returns the 
'Character string' with the format below;
Format
CommandFunctionProjector 
ReturnProjector status
CR0Status Read
00Power On
80Stand-by mode
40Countdown
20Cooling down
10Power Malfunction
28Cooling down at the temperature anomaly
02Unable to receive the RC232C command.
24Cooling down at Power Management mode
04Power Management mode after Cooling down
21Cooling down after the projector is turned off when the lamps 
are out.
81Stand-by mode after Cooling down when the lamps are out.
88Stand-by mode after Cooling down at the temperature 
anomaly.
2CCooling down when the projector is turned off by the shutter 
management function.
8CStand-by mode after Cooling down by the shutter 
management function. 
CR6Temperature ReadS1 S2 S3
S1 = Temperature at Sensor 1 (˚C)
S2 = Temperature at Sensor 2 (˚C)
S3 = Temperature at Sensor 3 (˚C)
(ex.) S1 = 12.3˚C,  S2 = 23.4˚C, S3 = 34.5˚C
 --> The projector displays “12.3 23.4 34.5”
    ( For each sensor, two digit and the tenth place numbers are 
displayed with a space between each temperature.)
?Communication failure
The tables on page 82 and 83 show the typical command lists for controlling the projector.  Please consult your 
local dealer for further information of other commands. 
						

							
U .S  .A .
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel  : 800-242-3454 (949)-457-0200 
Fax  : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12, 65510 Idstein
Deutschland
Tel  : 06126-9371-0 
Fax  : 06126-9371-14
E-Mail : [email protected]
Canada
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada 
Tel  : 800-563-3454 (705)-527-4084
Fax  : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Eastern Europe
EIKI CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7 
Czech Republic
Tel  : +42 02 20570024
    +42 02 20571413 
Fax  : +42 02 20571411
E-Mail : [email protected]
ˆ
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka, 
530-0028 Japan
Tel  : +81-6-6311-9479 
Fax  : +81-6-6311-8486
WorldWide Website http://www  .eiki .com
KS3B© 2008 Eiki International, Inc.
China
EIKI (Shanghai) Co.,LTD
1. Dapu Road, Golden Magnolia 
Plaza #2109 Shanghai, 
200023 China 
Tel : 86-21-5396-0088 
Fax  : 86-21-5396-0318
E-Mail : [email protected]