Eiki Projector Lc X6 User Manual

							21
Installation
Terminals to connect AC power cord and other equipment are
located in the front part of the projector for easy setup.  The
terminal area is masked with the front cover to protect them from
dust and others, and hide messy cable connections.  
The projectors front terminal area has two replaceable Interface
board slots.  The projectors functions can be extended by
installing the optional interface boards into the terminal slots.  A
vacant slot (Input 5) is provided in your purchasing the projector.
Install or replace the optional interface boards as follows:
Remove 2 screws from an interface board installed in the
projector.
Pull out the interface board by holding its handles and remove it.
Then, insert another board along with the guides inside the slot to
fit the socket into the inside plug.  Tighten screws to secure the
board.
Screws
Socket
Terminal board
✔Notes On Ordering or Using Optional Interface Boards:
When ordering or using the Optional Interface Boards, contact your sales dealer and
tell the Model no. of your desired board (p75) and Option Control No. shown in the
Information menu. (p31and 61)
✔Note:
When installing or removing the interface board, disconnect the AC power cord from
the AC outlet before doing it.
Remove and replace the front cover following the procedure
below:
Pushing the button Aon right side of the front cover, pull the part
forward to remove the front cover.
To replace the front cover onto the projector, insert back the left
part of the cover into the projector and then push the entire cover
back the projector.  Make sure the front cover is locked with the
buttonAand  fit on the projector.
Pull this part forward
with pushing button A.
A
Interface Board Slots
Caution
Do not push hard or give a strong shock to the
cover.  It may cause damage to it.
Terminals
Front cover
Connection Terminals
Installation
Option Control No.
See Option Control No. in the Information menu
to order any optional interface board.   
						

							22
Installation
Connecting to Computer (Digital and Analog RGB)
Cables used for connection
qVGA Cable (HDB 15 pin) tAudio Cables (Mini Plug: stereo)✽
wDVI-D Cable  (✽= Not supplied with this projector.)
eBNC Cable 
✽
rSerial Cross Cable (RS-232C) ✽
q t✽ Monitor Output Audio Output
DIGITAL (DVI-D)AUDIO 2
(Stereo)
q
Monitor Input
SERIAL PORT IN
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet. 
w
Monitor Output
ANALOG OUTANALOG IN
SERIAL PORT OUT
R    G       B    H/V    VMonitor Output
e
Audio Output PC Serial Port
Other Projector
SERIAL PORT IN
r✽
r✽
AUDIO 1
(Stereo)
t✽ 
						

							23
Installation
Connecting to Digital PC/AV  Equipment (Warp & Blending)
Cables used for connection
qDVI-D Cable  
wSerial Cross Cables (RS-232C)
✽
(✽= Not supplied with this projector.)
Refer to the enclosed operation manual for details in operation of
the Warp & Blending feature.
PC Serial Port
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet. 
q
Digital Output
Other Projector
SERIAL PORT IN
SERIAL PORT INSERIAL PORT OUT
w✽
DIGITAL (DVI-D)
Installation
✔Note:
Connect digital PC/AV source to the DIGITAL (DVI-D) terminal with a DVI-D cable to
adjust projected images from the computer connected to the SERIAL PORT IN
terminal with Warp and Blending feature.
w✽ 
						

							24
Installation
Connecting to Video Equipment (Digital and Video)
INPUT 3
VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO R-AUDIO-L
(MONO)
Cables used for connection
qVideo Cable ✽
wS-Video Cable ✽
eDVI-D Cable
rAudio Cables (RCA x 2, Mini Plug: stereo) ✽
(✽= Not supplied with this projector.)
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet. r✽
VIDEO
w✽ q✽
S-Video Output Audio Output
AUDIO
e r✽
DIGITAL (DVI-D)
Digital Output
(HDCP compatible)Video Output
S–VIDEO
AUDIO 1
(Stereo)
Audio Output
(Stereo)(R)     (L)
(R)     (L) 
						

							25
Installation
Connecting to Video Equipment (Component and RGB Scart)
INPUT 3
VIDEO/Y   Cb/Pb     Cr/Pr
R-AUDIO-L
(MONO)
Cables used for connection
qBNC Cable ✽ 
wScart-VGA Cable ✽ 
eComponent Cable ✽  
rAudio Cables (Mini Plug (stereo) + RCA x 2, or RCA x 1) ✽
(
✽= Not supplied with this projector.)
Note:
When connecting the cable, the power cords of both the projector and
the external equipment should be disconnected from AC outlet. 
r✽
RGB Scart
21-pin OutputAudio Output
w✽r✽ r✽q✽
Component Video Output
(Y, Pb/Cb, Pr/Cr)Audio OutputComponent 
Video Output
(Y, Pb/Cb, Pr/Cr)Audio Output
ANALOG INAUDIO 2
(Stereo)
AUDIO 1
(Stereo)
Y    Cb/Pb   Cr/PrY   Cb/Pb  Cr/PrAUDIO
e✽
(R)     (L)(R)    (L)
Installation
(R)     (L)
(R)     (L) 
						

							26
Operating the Projector
You can operate the projector with the projectors top control, the remote control or a USB mouse (not provided).  The
remote control is available as wireless and wired.
Operational range of the wireless remote control is within about 32.8 (10m) from the projector.  Operational range differs
depending on environments where the projector is used.  Any obstruction to air signal between the projector and the
remote control may prevent the remote control from working properly.
The wireless remote control does not work
when the remote control cable is
connected to either the projector or the
remote control.  Remove the remote
control cable from both of the projector and
the remote control when using it as
wireless.
Wireless Remote Control Operation
Projector Top Control Operation
Mouse Operation
Connect the R/C JACK on the projector and the remote
control with the remote control cable when operating
the remote control as wired.
Connect the USB terminal on the projector and a USB
mouse when operating the projectors menu with the
USB  mouse.  A mouse cursor will appear on the
screen with the mouse connected.  
Mouse operation offers the On-Screen Menu control
only.  Other operations are unavailable with the USB
mouse.  For details of the mouse operation, refer to
page 34~35. 
Wired Remote Control Operation
R/C jack
Remote control
cable
USB terminal
Basic Operation 
						

							27
Basic Operation
Basic Operation and Reference Buttons
Operations & Buttons
Ref. Pages
On-Off28, 29
Lens Shift➔ ➔ 30
Zoom➔ ( e
ed
d)   30
Focus➔ ( e
ed
d)     30
Shutter30, 55
Auto PC Adjust31, 41
Input Selection (Input 1–5) 31, 37~38
Information31, 61
Keystone –➔ 32, 49
Screen Selection – 32, 48
Freeze – 32
P-Timer – 32
D. Zoom –➔ 33, 49
Remote CH and ID – 16, 17
Volume –➔ 33
Mute – 33
Menu34~36
Select
Cancel
Pad
Pad
Pad
Pad
Pad
PadPad
For detail operations other than those on this page, follow the respective menu operations described later.
Remote ControlTop Control
Basic Operation
These buttons are used on the
menu operations.These buttons are used on the
menu operations. 
						

							28
Basic Operation
Turn on the MAIN On/Off switch of the projector.  The
LAMP indicator lights red, and the READY indicator lights
green.
Press the POWER ON-OFF button on the top control or the
remote control.  The LAMP indicator dims, and the cooling
fans start to operate.  The preparation display appears on the
screen and count-down starts.  The input and source
selected last appears after 20 seconds count-down.
2
3
1Complete peripheral connections (with Computer, VCR, etc.)
before turning on the projector. (Refer to page 22~25 for
connection.)
Turning On the Projector
What is PIN code?
PIN code is a security code using Personal Identification Number that
allows the person who knows it to operate the projector.  Setting PIN code
prevents the projector from being operated by an unauthorized person.
A PIN code consists of a four-digit number.  Refer to Security in Setting on
page 57 for locking operation of the projector with your PIN code.
Pointer(yellow frame)
After the OK icon
disappears, you can
operate the projector.  
PJ PIN code Input Dialog Box
Enter a PJ PIN code
Select a number by softly tapping the control pad and fix the number with
the SELECT button.  The number will change to ✳.  If you fixed a wrong
number, move the yellow frame pointer to C or Ent once, then enter the
correct number again.
Repeat this step to complete entering a four-digit number. 
When the four-digit number is fixed, move the yellow frame pointer to
Ent.  Press the SELECT button so that you can start to operate the
projector.
If you entered a wrong PIN code, the entered number (✳✳✳✳) will turn red
and disappear.  Enter a correct PIN code all over again.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started.  Set a new PIN code with special
care, write it down in column on page 81 of this
manual, and keep it at hand.  Should the PIN code be
missing or forgotten, consult your sales dealer or the
service station.
16
The preparation display disappears after 20 seconds.
(See page 37~38 for Input)
Selected Input and Source
If the projector is locked with a PJ PIN code, PJ PIN code
Input Dialog Box will appear.  Enter the PIN code as
instructed below.   
						

							29
Basic Operation
Press the POWER ON-OFF button on the top control or the
remote control, and a message Power off? appears on the
screen.  1
2
3
Press the POWER ON-OFF button again to turn off the
projector. The LAMP indicator brightly lights red and the
READY indicator goes out.  After approximate 90 seconds,
the READY indicator will light green again and then the
projector can be turned on by pressing the POWER ON-OFF
button.
The Cooling fans operate for approximate 2 minutes after the
projector is turned off; keep operating more 30 seconds after
the READY indicator lights green. To power down the
projector completely, turn off the MAIN On/Off switch and
disconnect the AC Power Cord.
Turning Off the Projector
The message disappears after 4 seconds.
TO MAINTAIN THE LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
DO NOT DISCONNECT AC POWER CORD  WHILE
COOLING FANS ARE RUNNING OR BEFORE POWER
INDICATOR LIGHTS RED.  OTHERWISE IT WILL
RESULT IN SHORTENING LAMP LIFE.
✔Note:
• The projector cannot be turned on for about 90 seconds after turned off.  You can
turn it on again after the READY indicator lights green.
• When the On start function is on, this projector is turned on automatically by
connecting the AC power cord to an AC outlet.  (See page 54 for the On start
function.) 
• Do not operate the projector continuously without rest.  Continuous use may result
in shortening the lamp life.  Turn off the projector and give it a rest about an hour in
every 24 hours.   
• This projector monitors internal temperature and automatically controls the running
speed of the cooling fans. 
• If the WARNING TEMP indicator blinks red or all the indicators except the LAMP
indicator are blinking, see “Warning Temp Indicator” on page 62.
• When “Power management” mode is Ready or Shut down, projector detects signal
interruption and turns off the Projection Lamp automatically after the set time has
passed.  Refer to “Power management” on page 54.
Basic Operation 
						

							30
Basic Operation
Press the ZOOM/FOCUS button and adjust with the Control pad.
Press the LENS SHIFT button and adjust with the Control pad.
Shutter Function
Shutter function allows you to completely block out light to the
screen.  Press the SHUTTER button to close the shutter inside the
projector.  To open up the shutter, press the SHUTTER button
again.  Refer to p55~56 for detail of  setting for the Shutter
function. 
✔Note:
• The SHUTTER buttons on the top control and the remote control can not be
effective when Shutter Protection is On in the Setting menu.  (p55)
• The SHUTTER indicator on the projectors top lights blue when the shutter is closed.
(p10)
•When the Shutter level is High contrast in the Setting menu, the shutter opens up
80%.  (p55)
•The projector will shut down automatically when the set time on Shutter
management has passed.  (p56)
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER  SHUTTER D.ZOOM
D.ZOOM
ZOOM ZOOMFOCUS
FOCUS ON-OFF ON-OFFSHUTTER button
SHUTTERINPUT
INFO.  AUTO
PC ADJ.
POWER P
Remote Control
Top Control Remote Control Top Control
Press the ZOOM/FOCUS ed button to adjust Zoom and Focus.
SHUTTER button
Zoom and Focus Adjustment Lens Shift Adjustment
•When the lens position comes right in center
vertically, the vertical arrows turn red. 
•When the lens position comes right in center
horizontally, the horizontal arrows turn red.