Eiki Projector Lc X6 User Manual

11
Preparation
Top Control
LENS
SHIFTMENU
CANCEL
SELECTZOOM
FOCUSSHUTTERINPUT
INFO.  AUTO
PC ADJ.POWER P
qwerty
oi
u
uINPUT button
Switches input sources.  (p31)
yAUTO PC ADJ. button
Operates the Auto PC adjustment function.  (p31)
eCANCEL button
Cancels the selection and returns to the previous menu.  
t
INFO. button
Displays Information.  (p31) 
wMENU button
Opens or closes the On-Screen Menu.  (p34, 35 )
oPOWER ON-OFF button
Turns the projector on or off. (p28, 29)
iSHUTTER button
Closes and opens up...

12
Preparation
  ANALOG OUTINPUT 3
INPUT 1
INPUT 2  ANALOG IN
DIGITAL (DVI-D)
AUDIO 1
AUDIO 2
VIDEO/Y    Cb/Pb          Cr/PrG                B               R            H/V               V
VIDEO/Y   Cb/Pb     Cr/PrS-VIDEO R-AUDIO-L
(MONO)
Te r minals
q
w
e
r
eINPUT 3 terminals
AUDIO (R-L)
Connect the audio output from video equipment
connected to VIDEO/Y Cb/Pb Cr/Pr jacks or S-VIDEO
jack to these jacks.  (When the audio output is
monaural, connect it to L(MONO) jack.  (p24, 25)
VIDEO/Y, Cb/Pb, and...

13
Preparation
A built-in micro processor which controls this unit may occasionally
malfunction and need to be reset. This can be done by pressing the RESET 
button with a pen, which will shut down and restart the unit.  Do not use the
RESET function excessively.
q
ertyu
uSERIAL PORT IN
When controling the projector from a computer, connect
the computer to this terminal with a serial cross cable
(commercially supplied).
tUSB (Series B)
This port is used for the projector maintenance.
ySERIAL PORT OUT...

14
Preparation
Remote Control 
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTEVOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
KEYSTONE
SHUTTER D.ZOOM
ZOOMFOCUS ON-OFF
MENU
CANCEL
INFOAUTO PC
SCREEN
FREEZE
P-TIMER SOUND
REMOTE
VOL.
MUTE
CH
ID
LENS SHIFTKEYSTONE
SHUTTER D.ZOOM
ZOOM FOCUSON-OFF
q
w
u
i
e
r
y
!0
o
oZOOM buttons
Adjust zoom of the image. (p30)
rCONTROL PAD (semiconductive touchpad)
Selects an item or adjusts value in the On-Screen Menu.
This is also used to pan the image in the Digital zoom +...

15
Preparation
!1SCREEN button
Selects screen sizes.  (p32)
!2
INPUT 1-3 buttons
Selects input source (INPUT 1 - INPUT 3).  (p31)
!0AUTO PC button
Operates the Auto PC adjustment.  (p31)
qMENU button
Opens or closes the On-Screen Menu.  (p34, 35)
wFREEZE button
Freezes the projected picture.  (p32)
!4REMOTE RESET/ON/ALL-OFF switch
When using the remote control, set this switch to “ON.”
Set it to “ALL OFF” for power saving when it is not
used.  Slide this switch to RESET with holding down
the CH and ID...

16
Preparation
This wireless remote control uses radio frequency signal.  You can switch four frequency channels prepared and select a
remote control ID from eight IDs.  The Remote Control Channel selection prevents radio frequency interference from the
other equipment and the Remote Control ID selection allows you to operate several projectors with their respective remote
controls without mutual interference among those projectors.
Wired Remote Control Transmitter
The remote control can be used as a...

17
Preparation
Remote Control Battery Installation
To insure safe operation, please observe the following precautions :
●Use (2) AA, UM3 or LR6 type alkaline batteries.
●Replace two batteries at the same time.
●Do not use a new battery with a used battery.
●Avoid contact with water or liquid.
●Do not expose the remote control to moisture, or heat.
●Do not drop the remote control.
●If a battery has leaked on remote control, carefully wipe case clean and install new batteries.
●Risk of explosion if battery...

18
Install the projector in a safe place.  Before installation, read Safety
Instructions thoroughly and check the installation place.  Install the
projector in a place with sufficient strength to support the
projectors weight.  Installation on an unstable stand, cart, or
ceiling may cause serious injury or accidents.  
Do not place the projector where is extremely hot and humid.  Do
not place the projector where is dusty and smoky.   When installing
the projector in dusty and smoky places or in a place...

19
Installation
Adjustable feet Lens shift feature is provided to move the position of the projected image vertically by 50% and horizontally by 10%
respectively without any image distortion.
✽Lens shift range varies depending on lens and projectors.  The range in this manual is the case of LNS-W04.
Level Adjustable Feet
This projector has four level adjustable feet.  The projection angle
can be adjusted by rotating each foot.  Adjust the four feet to
obtain best position of the projected image and make...

20
Installation
Connecting AC Power Cord
This projector uses nominal input voltages of 120 V or 200-240 V
AC.  This projector automatically selects correct input voltage.  It is
designed to work with single-phase power systems having a
grounded neutral conductor.  To reduce risk of electrical shock, do
not plug into any other type of power system.
Consult your authorized dealer or service station if you are not sure
of type of the power being supplied.
Connect a projector with peripheral equipment before...